The SBL configuration no longer differs in any detail (except its name)
from the "standard" UpSquared configuration, so it is removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This needs to be pushed down to the SoC level, as it's an Apollo Lake
feature, not a feature of the UpSquared. Remove the Apollo Lake
references to the PCI devices because these will not be used when I2C
support is restored.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This option is no longer used in the dts_fixup.h file since there
are no SBL-specific fixups.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The ACRN board configuration is not suitable for production use,
but many people are mistakenly using it as a starting point for
real-time applications. I've added a note to clarify.
Signed-off-by: Charles Youse <charles.youse@intel.com>
Increase ram size as flash simulator need it for
emulated storage. The qemu_x86 flash size is puted back to
its original value of 4092K
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The UARTs are on the SoC, not the board, so move their descriptors
to the SoC-level. Also turn on auto IRQ detection as these are PCI-
attached and their IRQs are subject to change depending upon firmware
settings.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The '#if XIP' in the DTS file never worked properly,
causing the QEMU build to think it has much more RAM
then it actually has. If RAM overflowed, this would not
be caught by the build, instead there would be strange
crashes when the data copy takes place.
The QEMU targets themselves are not XIP, everything
is actually RAM, but the first 4 megabytes are
considered to be a memory-mapped flash region. This
is done to ensure that the XIP data copying infrastructure
doesn't bit-rot on x86. We are at the point where
a lot of things depend on this, so just select it in
the board Kconfig instead of enabling in the
defconfigs.
Fixes: #15835
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A new function pcie_irq_enable() is added to be used in lieu of
irq_enable() when the target device is PCI(e)-attached. The function
attempts to use MSI, when configured in the kernel and supported by
the endpoint; failing that, it will verify that IRQ requested is in
fact routed to the device by the boot firmware before enabling it.
The NS16550 UART driver is updated to use pcie_irq_enable().
The PCI(e) shell is extended to dump information about wired IRQs.
The up_squared devicetree is fixed (reverted?) to IRQ5 for UART1.
The galileo enables MSI by default.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Reduced flash size for QEMU x86 so it does not consume a lot of RAM
memory where it is simulated.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
We already select HAS_DTS at the arch level for X86 so we don't need to
duplicate it at the board level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to generalize the currently specialized nRF51 IC setup hook,
make the following changes:
- Generalize the hook to bt_ic_setup()
- Use a weak NOP version by default
- Move the currently existing one to the board folder
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Fixes broken CC2520 on quark_se_c1000_devboard configuration after
commit 25d17db.
Fixes#15070
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
For some reason we dropped the simulation keyword and this platform is
not running any tests, we are just building the tests.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
On Clear Linux, the CFLAGS is set and defines a number of aggressive
checks and optimizations. This causes a build failure when generating a
GRUB2 boot loader image using the 'build_grub.sh' script.
Unsetting it within the script allows it to proceed and successfully
build a functional GRUB2 boot loader image to be used with Zephyr.
Fixes: #14289
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
One of the bullet list items didn't get rendered properly because
continuation line wasn't indented.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Move the original documentation in the arduino_101 board to a common
section in the Bluetooth documentation and document the use of `btmon`
in general.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Based on prior work by @dcpleung. It's suboptimal, but it provides a
working starting point for ACRN work. The x86 board/SoC abstractions
really need to be refactored to make this "board" (and other x86-based
"boards", both extant and future) cleaner and easier to maintain. Punt.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
It is also possible to use 'west' to build the 'hello_world' sample
application for the UP2 (up_squared) board. This patch makes it
explicit in the documentation.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Linking to API material requires knowing the pecularities of how
doxygen, sphinx, and breathe work. In an attempt to hide some of this
we're preparing the current docs to allow use of configuration defaults
that will let us more simply use a default role that will hunt for a
reference target in the various domains that are available by using a
default "role" of "all". This will let us use the simple notation
`functionname` or `typename` without fully specifying the reference as
:c:func:`functionname`.
This patch cleans up exising docs that were (incorrectly) using single
backtics where double backtics should have been used, and also found
some typos (such as a space between the role name and the reference,
such as :file: `filename`, and a missing colon such as
c:func:`functionname`)
This is a start to address issue #14313
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The build_grub.sh script cherry-picks 3 commits from the master branch
of grub because more recent build tools fail to build the latest stable
release (which is 2.02). This solves the problem on Fedora 29 for
example, but is not sufficient for Clear Linux.
This patch modifies the build_grub.sh script to use
grub-2.02-285-g5bc41db75 (latest from master as of 13 of March 2019).
That version compiles 'out-of-the-box' in the latest Ubuntu, Fedora and
Clear Linux.
There are additional tools required on the host system and the
documentation has been updated accordingly.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This build target is intended to verify that enabling the
IAMCU ABI doesn't have any bit-rot since we can easily
run this under emulation.
However, the QEMU boards all derive from the generic IA32
SOC definition, which is any pc-like hardware. We need
to disable these mitigations for this target since the
IAMCU compiler doesn't even recognize instructions like
'lfence'.
Fixes: #14315
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fedora 29 (and possibly other disctributions) are nowadays coming with
very recent versions of gcc (8.x) and binutils. These will cause some
compilation error when running the 'grub_build.sh' script to create a
GRUB2 boot loader image.
Fortunately, both issues have been fixed and merged in the upstream
project. This patch modifies the build script to cherry-pick those to
the local cloned version of grub before building it.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Most of these are from source'ing a file within an 'if PINMUX', and then
adding another 'depends on PINMUX' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. There are no "conditional includes" in Kconfig, so
'if FOO' has no special meaning around a 'source'. Conditional includes
wouldn't be possible, because an 'if' condition could include (directly
or indirectly) forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
According with MISRA-C every switch-clause must terminate with an
unconditional break.
MISRA-C rules 16.1 and 16.3
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
UART_QMSI_0_BAUDRATE was removed by commit 17c6456678 ("drivers/uart:
Use dts to set uart priorities for QMSI driver").
There's a reference to CONFIG_UART_QMSI_1_BAUDRATE as well, but getting
rid of it requires documentation updates.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The MMIO addresses for peripherals are being assigned by BIOS
at boot. Different BIOS versions and number of enabled peripherals
affect how those addresses are assigned. This invalidates
the addresses for UART defined in DTS. Turn on PCI enumeration
so UART addresses are probed at boot to avoid non-usable
UART and black console.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Previous rename from CONFIG_* to DT_* left a few remaining
CONFIG_*. So rename them manually now.
Fix#13753
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Recent versions of GCC won't build grub-2.02 because they're more
pedantic about warnings. This has been fixed upstream but is not
yet part of any release. The build script is modified to apply the
relevant commits before building.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix setting of the I2C bus master device name for the GPIO_PCAL9535A
device and PWM_PCA9685. We need to extract them from the dts otherwise
they will just get set to "".
Fixes#13458
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We've removed the QMSI RTC driver as part of the new counter API. So
any old rtc tests don't build for QMSI based boards anymore. Switch
this from 'rtc' to 'counter' in the board.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To avoid confusion, callbacks using ordinal pin numbers
is going to be reverted. So the driver has to be re-worked
to expose multiple devices so each device has 32 pins.
Also fixes#12765
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
PAE tables introduce the NX bit which is very desirable
from a security perspetive, back in 1995.
PAE tables are larger, but we are not targeting x86 memory
protection for RAM constrained devices.
Remove the old style 32-bit tables to make the x86 port
easier to maintain.
Renamed some verbosely named data structures, and fixed
incorrect number of entries for the page directory
pointer table.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Convert the w25qxxdv driver to use device tree for SPI device params.
Updated the Arduino 101 config to use device tree to specify the SPI
flash. Update the arduino_101_sss to drop Kconfig support for the
w25qxxdv flash.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
"-machine type=pc-0.14" appears to be the option which leads to
broken PCI emulation in QEMU, where PCI enumeration reports one
IRQ number (11), while actually IRQ 10 is emulated by QEMU.
"-vga none" and "-display none" appear to be just subordinate of
"-machine type=pc-0.14" and are required to get qemu_x86 into
bootable state.
Fixes: #11706
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add documentation for the quark_se_c1000_devboard with links to platform
guidelines and other details.
Fixes#11166
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Merge up_squared_dts_fixup.h and up_squared_sbl_dts_fixup.h into
dts_fixup.h. This allows us to remove BOARD_DIR from being included
everywhere.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix link text to remove substitutions that are ignored by Sphinx. Also
replace link to Quark SOC HW ref manual to be from an Intel site (not
Russian).
Fixes: #11516
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Added support to the ti,cc2520 binding for optional GPIO signals and
moved the quark_se_c1000_devboard to define those signals in the DTS.
This lets us remove board.h and some #defines & fake Kconfig symbols
from the quark_se_c1000_devboard board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CC2520 device is specific to the quark_se_c1000_devboard not the
intel curie SoC. Move the device node where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the in tree user of cc2520 uses device tree to configure SPI
and GPIO params, we can remove and convert the driver to utilize DT
only. This means removing the Kconfig options that come from DT and
rename CONFIG_ to DT_ for those options.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of cases of CONFIG_I2C_x_IRQ_PRI should be
DT_I2C_x_IRQ_PRI. So go ahead and fix them up. Only the i2c_nios
driver still uses Kconfig for getting priority.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a primitive board configuration for the UP Squared board to
work properly with SBL(Slim Bootloader).
- https://github.com/slimbootloader/slimbootloader
- https://slimbootloader.github.io/
BOARD shall be 'up_squared_sbl'
cmake -GNinja -DBOARD=up_squared_sbl ..
ninja
Signed-off-by: Aiden Park <aiden.park@intel.com>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Previously we had a set of magic #define's in board.h that would both
enable and set the GPIO controller & pin if a given board used a GPIO
for USB VBUS. Now we make it a proper Kconfig set of options that
specify if the feature is needed, the GPIO controller device name, and
pin number. In the future this should move to devicetree.
Updated the related boards that used this feature to set the Kconfig
options in the Kconfig.defconfig
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce new Kconfig option for selecting either slip or ethernet
connectivity to host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This required wiring external daughter board by hand, it's not provided
by the board directly, let's remove this.
Applying the change on relevant samples.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove either duplicate settings between arch & board, or just set
HAS_DTS at the arch level since all the boards for a given arch support
DTS now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Options "-clock dynticks" and "-balloon none" are deprecated and
produce warning in recent Qemu versions, so remove them.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove some references <board.h> that aren't need or replace them with
<soc.h> where that is the proper include to pull in. Also use "board.h"
instead of <board.h> for how we include the file when its local to the
board code itself.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following dts warnings:
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/gpio@0:
simple-bus unit address format error, expected "d0c50000"
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/i2c@91528000:
simple-bus unit address format error, expected "9158000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This feature was a useless noop based on mistaken API understanding.
The idea seems to have been that k_busy_wait() included guards to
ensure "clock_always_on" was true duing the loop, presumably because
the original author was afraid that "turning the clock off" would
affect the operation of k_cycle_get_32().
Then later someone came around and "optimized" this for Quark SE,
where the cycle counter is the RTC and unrelated to the timer driver
used by the clock_always_on feature. (Except even there it presumably
should have been done at the SoC level and not just in the C1000
devboard -- note that Arduino 101 never would have gotten this).
But it was all a mistake: "clock_always_on" has nothing to do with
en/disabling the system cycle timer (which never happens when the
system is active, that's a feature of idle), it's a control over the
delivery of timer interrupts. And needless to say we don't care about
timer interrupts when we're spinning on a cycle counter.
Yank the whole mess.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This will be usefull to tell when Ethernet device has its attributes
filled in by DTS rather than by Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert over x86 based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Makes the designware spi driver consistent with other spi drivers by
selecting HAS_DTS_SPI in the driver. This required adding spi nodes and
dts fixups to several arc and x86 socs, as well as enabling those nodes
in associated boards.
Also refactors the driver to use the base address, interrupt number, and
interrupt priority from dts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The i2c drivers now consistently select HAS_DTS_I2C, so we no longer
need to select it at the board level.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sets the HPET timer frequency (enabled by default) to 19.2MHz.
And also sets the local APIC timer frequencies according to
the SoC variant.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are currently three SoC variants for the UP Squared board:
Pentium, Celeron and Atom. This adds a board option to specify
for which variant is being built.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit b0d3b560238fac09e63064620de9ff820cf8cc47.
Since we now have a working ADC driver for Quark D2000,
re-add the tag.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The stub is used for testing only and is not compatible anymore with the
usage documented here.
Fixed#9772
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
set DISK_FLASH_MAX_RW_SIZE to 256, as maximum bytes that can be
programed to SPI FLASH by Page Program Command is 256.
Fixes#8506
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The board config has been verified to boot with serial console
on the Atom version of the UP Squared board. So the references
to Pentium/Celeron can be removed. Moreover, add some notes on
BIOS settings, as it may change the MMIO addresses for various
IP blocks.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add the necessary bits to enable the I2C controllers on
the UP Squared board. Only the ones exposed through the HAT
connector(s) are enabled by default.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a primitive board configuration for the UP Squared board
containing Apollo Lake based Pentinum and Celeron SoC. This has
been tested on model UPS-APLP4-A10-0432.
This starts from the minnowboard configuration, and document
from galileo.
Origin: Original
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This extends the build_grub.sh script so that it can build 64-bit
Grub UEFI application, and thus enabling us to boot on systems
with 64-bit BIOS.
Also updated the script to checkout the tag grub-2.02 since
v2.02 has been out.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The PHYS_LOAD_ADDR Kconfig symbol was removed by commit b8ea7c889d
("x86: remove HAS_DTS checking"). The ROM_SIZE Kconfig symbol was
removed by commit e524f0b846 ("dts: x86: derive RAM and ROM size from
dts instead of Kconfig").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add first set of boards which can be built with xtools, this will
include all boards at some point, so we might need a better way to
whitelist toolchains that does not include changing every single board
definition file. For now enabling those needed for testing the new
toolchain.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Make these "choice" items instead of a single boolean that implies the
element unset.
Also renames WAITQ_FAST to WAITQ_SCALABLE, as the rbtree is really
only "fast" for large queue sizes (it's constant factor overhead is
bigger than a list's!)
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that for any of the removed properties though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
CONFIG_SPI_FLASH_W25QXXDV_MAX_DATA_LEN is a left-over from old SPI API
usage. Now, there is no limit (besides the flash size) in SPI data
transaction.
Fixes#8327
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These symbols were removed by commit ed26b95 ("drivers/gpio:
Removing dts generated options in QMSI Kconfig"). The settings should
come from DTS now.
Commit 9611002f7a ("boards/x86: Use right GPIO names for CC2520")
fixed some of the references, but there are still others left. Guess
that the same fix is appropriate in those spots (hardcoded
"GPIO_0"/"GPIO_1" names).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
GPIO_QMSI_<0/1>_NAME are now generated through DTS. Until CC2520
settings are generated through DTS, let's use direct gpio names
instead.
Fixes#8086
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
According to INTEL-SA-00115[1], Intel(r) Atom(tm) Processor E Series
are affected. All Minnowboards sports one of these processors.
[1]: https://goo.gl/CKyLQy
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The Kconfig option TOOLCHAIN_VARIANT (not to be confused with
ZEPHYR_TOOLCHAIN_VARIANT) is a legacy configuration option that has
very few use-cases and can easily be dropped.
It's functionality is easily covered by CONFIG_X86_IAMCU and
ZEPHYR_TOOLCHAIN_VARIANT.
This commit removes all references of it from Zephyr.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The current method of setting the openocd runner arguments works for
direct invocation from the command line, but the values that are
written to the CMake cache are not properly separated and are
difficult to parse, due to the fact that in several cases, option
values contain spaces.
Adjust these runner arguments so that the options and their values are
separate list items. This makes it possible to parse them accurately
from the CMake cache.
No functional changes.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
This target is already using the rbtree as part of CONFIG_USERSPACE,
so it incurs no code size overhead (actually it's a little smaller)
when using the scalable scheduler and waitq implementations.
The change also gets us test coverage of those choices on a default CI
target.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
patch removes Kconfig defines for RAM and ROM size in x86. Instead
these values are derived from dts.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
boards/x86/arduino_101/arduino_101_defconfig currently enables
CONFIG_UART_QMSI_0_HW_FC (HW flow control on UART 0), but doesn't enable
CONFIG_UART_QMSI_0 (the UART itself), which is a direct dependency.
This means CONFIG_UART_QMSI_0_HW_FC remains disabled despite the request
to enable it, and kconfig.py prints a warning.
Enable CONFIG_UART_QMSI_0 in the arduino_101_defconfig.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We are testing and building this already using qemu_x86, no need to
build the same thing all over again.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
QMSI is not updated to latest SPI API. Switching to native DW driver,
until we find a way either to update the shim drivers in a
non-performant way, or updating QMSI itself enabling support for
scatter-gather type of buffers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>