Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use new configuration API, replace callback enable/disable with
interrupt enable/disable, and set active level in devicetree source.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since this was converted to the setup/handle/process idiom in master
the conversion is straightforward.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Put all the devicetree configuration data into a config structure in
flash, which removes some ultra-long identifiers from the code and
makes it more readable, and prepares for multiple instance support.
Consistently use the interrupt signal datasheet name for all objects
that are specific to that signal, including configuration structure
tags and function names.
Update the trigger idiom for setup/handle/process stages.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update ALERT active level in all devicetree files. Capture GPIO flags
in static configuration. Add internal API to enable and disable
interrupt, to release the handlers when an alert occurs, and to
re-enable the signal when the handler completes. Check for alerts
received during periods when the interrupt was disabled.
Extend the example to handle both above and below range triggers and
alerts that are present on startup.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Correct DRDY active level to default active-high, switch to new
interrupt configuration.
Also fix a common bug where an already-active DRDY signal is not
properly handled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Define a binding for the Bosch BMA280 sensor. Remove the Kconfig
settings and update the driver to use the devicetree information.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add sensor driver for the internal temperature sensor present in the
NXP Kinetis SoC series.
The driver allows reading the die temperature and the voltage of the
external voltage reference used for calculating the temperature.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The firmware version on the CCS811 on nrf52_pca20020 is generally
version 1.1, which does not set the data ready bit in the status
register. Assume that a non-zero CO2 measurement on that version is
fresh for the purposes of determining the fetch status.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The application may want to know the configured mode without inspecting
Kconfig macros; this is important for proper management of BASELINE
which is mode-dependent.
It also may need to know the version of the hardware and firmware, as
the behavior of application firmware 2.0 is significantly better than
version 1.1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This mode is documented as producing a raw result every 250 ms that the
application must convert to eCO2 and eTVOC readings. In practice
application firmware 2.0 appears to convert the readings as with all
other rates.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Expose the entire content of the ALG_RESULT_DATA block to the
application, primarily so the status and error flags can be seen. With
those available the application has the ability to detect that a stale
result has been provided so sensor_fetch_sample() can return -EAGAIN in
this case instead of -EIO, and it doesn't need to block which is
annoying.
This should also make the sensor usable on older Nordic Thingy:52
devices with outdated CCS811 application firmware that doesn't properly
implement the DATA_READY bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Accurate estimate of gas presence requires temperature and humidity
data. Add API to update these values.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use CMSIS-standard bit mask and offset macros. Rename the field to more
closely match the data sheet. Use slightly less magic numbers for the
scale multipliers.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Proper use of the CCS811 requires maintenance of the BASELINE
register value measured in clean air at various points in the sensor
life cycle. The sensor driver abstraction has no facility to support
this, so add an application header with functions to fetch and update
the register value.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add the standard suite of trigger configuration options. Add driver
support for the DATA_READY and THRESHOLD triggers. Note cross-module
dependency as configuring the trigger requires a controlled modification
of the sensor registers and the sensor driver API doesn't support this.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The original implementation relied on the DATA_READY bit of the STATUS
register to indicate when a reading was available. This bit remains
clear for the first several readings produced by the CCS811.
When INT_DATARDY is set in MEAS_MODE the nINT signal will remain
asserted until ALG_RESULT_DATA is read. If this is treated as a LEVEL
signal, which is the common case in Zephyr, gating the read of
ALG_RESULT_DATA on DATA_READY means the signal will never be cleared,
and the interrupt callback will be repeated immediately.
Since the STATUS register value is part of the ALG_RESULT_DATA block
just read the whole thing, and provide its content to the user only if
the DATA_READY bit is set.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The CCS811 has a measurement lifecycle that includes certain timing
constraints, including that calibration constants should not be applied
until the conditioning period has completed. If a device resets but the
CCS811 remains the process of inspecting current state and initializing
the device properly can be complicated.
Simplify this by forcing a reset of the device when the driver is
initialized. Should this cause hardship the necessary logic and
infrastructure to record time-of-last-reset across reboots and verify
measurement mode/baseline consistency can be added at that point.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Read the status and error in one function that provides its own
diagnostics.
Also change name of register to match datasheet.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The CCS811 can be in either boot mode (after powerup) or application
mode, and these modes have distinct register maps that share only some
content. The register written to switch from boot mode to application
mode is not available in application mode, so don't write to it in that
case.
Also respect the required timeout between APP_START and next I2C
operation.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Allow application to choose the measurement rate.
Measurement mode 4 (250 ms rate) is not supported because it we have no
support for processing the raw data it produces.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Asserting the WAKEn increases current draw. Turn it off when I2C is
not being used.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adds BME280 SPI chip select pin control if chip select is
configured for the device in the device tree.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Correct handling of device encoded temperature values, which combine a
12-bit 2s complement signed value with a separate sign bit. Rework
conversion between device and sensor temperature representations to
support negative temperatures in both domains.
Use a much simpler trigger configuration where the alert is driven by
comparator output, rather than as an interrupt that requires a pair of
I2C transactions to read and clear the flag.
Refactor the trigger infrastructure to use the setup/handle/process
idiom, which reduces duplicated code and to correctly detect alerts
present when the triggers are set.
Completely replace the sample with something that demonstrates
updating upper and lower threshold values to track moving
temperatures.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Added autocompletion to 'sensor get' command. After this change
device and channels are autocompleted. It is possible to provide
multiple channels for reading.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When asserts were disabled then sensor accepted any channel in
hts221_channel_get(). Changed to return -ENOTSUP when invalid
channel is provided.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
MPU6050 no longer using Kconfig to specify I2C addresses. Reference
to the removed symbol causes QA diagnostics. Remove the reference;
when AK8975 is converted to devicetree it may be possible to restore
the link between the sensors.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a binding for the sensor and replace all Kconfig selection of
hardware parameters with devicetree property values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
A single menu within an if like
if FOO
menu "blah"
...
endmenu
endif
can be replaced with
menu "blah"
depends on FOO
...
endmenu
Fix up all existing instances.
Also remove redundant extra menus underneath 'menuconfig' symbols.
'menuconfig' already creates a menu.
Also remove the menu in arch/arm/core/aarch32/Kconfig around the
"Floating point ABI" choice. The choice depends on FLOAT, which depends
on CPU_HAS_CPU, so remove the 'depends on CPU_HAS_FPU' too.
Piggyback removing a redundant 'default n' for BME280.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
- Added support for TMP117 in existing driver for TMP116
The Texas Instruments TMP117 is a higher precision upgrade
from TMP116. It shares most functionality, but has a
differing device ID.
This patch will run with the hardware IDs of both devices.
- Fixed an int promote issue in tmp116_channel_get
Negative temperature values in drv_data->sample were not
processed correctly.
The error occured during integer promotion from u16_t to s32_t
in this code line:
tmp = (s32_t)drv_data->sample * TMP116_RESOLUTION;
By first promoting to s16_t, the correct result is obtained:
tmp = (s16_t)drv_data->sample * (s32_t)TMP116_RESOLUTION;
- Made temperature resolution compatible to sensor API
The fractional part of the temperature was returned as a
multiple of 10^-7 deg.Celsius.
This differs from the resolution sugegsted by the sensor API,
which is 10^-6.
The driver is now returning temperature readings with
a resolution of 10^-6 deg. Celsius.
- The changed driver was tested using following hardware:
TMP117 attached to disco_l475_iot1 via i2c1
Signed-off-by: Hans Wilmers <hans@wilmers.no>
Adds a Shell Module for retrieving Sensor data. The following commands
were added:
sensor - Device commands
Options:
-h, --help :Show command help.
Subcommands:
get :<device_name> [chanel_idx]
list :List configured sensors
list_channels :<device_name>
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Define a binding for the Aosong DHT family of temperature/humidity
sensors. Remove the Kconfig settings, and update the driver to use
devicetree information.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DT_INST_0_ST_LPS22HH_CS_GPIO_CONTROLLER should be
DT_INST_0_ST_LPS22HH_CS_GPIOS_CONTROLLER, which is the name generated by
gen_defines.py.
Discovered while working on unrelated removing of special-casing for
clocks.
Co-authored-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Low frequency and high frequency clocks had separate devices
while they are actually handled by single peripheral with single
interrupt. The split was done probably because opaque subsys
argument in the API was used for other purposes and there was
no way to pass the information which clock should be controlled.
Implementation changes some time ago and subsys parameter was
no longer used. It now can be used to indicate which clock should
be controlled.
Change become necessary when nrf5340 is taken into account where
there are more clocks and current approach would lead to create
multiple devices - mess.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
When using the RC clock source a periodic calibration is invoked that
involves reading from the die temperature sensor. The code did not
protect against execution order that caused the periodic calibration
to be invoked before the temperature sensor was initialized.
Update the temperature sensor to detect that it has not been
initialized and so should reject attempts to fetch a reading.
Update the calibration code to do nothing when temperature reading
fails.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use LOG_DBG instead of LOG_ERR when BME680 chip is detected
and its ID verified successfully.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
The i2c_msg API details do not work correctly with Nordic TWI. Switch
to the higher-level and simpler API for register read and write. Also
add a tree configuration on a Nordic-based board.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LSM303AGR is a special one in terms of raw value scale among all devices
supported by lis2dh.c driver. Apply proper scale factor based on
sensitivity scale provided in LIS2DH and LSM303AGR datasheets.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All values were scaled by 8 instead of 12 for 16g compile-time selected
range. This resulted with values around 6.5 m/s^2. Scaling for runtime
configurable ranges was broken for all except 2g range option due to
totally broken lis2dh_range_to_reg_val().
Fix wrong scaling for 16g compile-time and all runtime selectable ranges
by reworking code that scales raw value. While doing this, change
lis2dh->scale type from 16 to 32 bits. This allows to slightly increase
final result precision by using the fact that raw values have maximum 12
bits precision, allowing us to multiply lis2dh->scale by (1 << 4)
compared to previous implementation.
Fix bug #19872.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
According to struct sensor_value documentation, val2 should be negative
for negative result. So drop code that tries to make val2 positive.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Cast to (void) the lsm6dso_mem_bank_set() calls as we
are not interested to the return value.
Coverity-CID: 205625
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit converts the existing hcm5883l 3-axis magnetometer
driver to use device tree for the I2C and GPIO selection.
It also adds a basic sample application for this sensor, using the
frdm-k64f development board to demonstrate how the interrupt
GPIO pin and I2C bus can be selected.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Convert bmg160 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert bmm150 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert max44009 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert mcp9808 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sx9500 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert tmp112 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert th02 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update lis3mdl-magn dts binding to include GPIO interrupt pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update ccs811 dts binding to include GPIO pins for wakeup, reset, and
interrupt and change driver code to get the GPIO pin and controller
info from DT instead of Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The LIS2MDL supports SPI half duplex mode with a single data line
by default (3-wire), but it might configured to switch to standard
full duplex mode (4-wire).
Signed-off-by: Armando Visconti <armando.visconti@st.com>