The big cherry-picking left some invalid code so remove/fix
it in order to pass the compilation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to a typo, channel and frequency were compared causing the
connection to fail for any combination.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Use the WPA cli command to disconnect a station in AP mode.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The WPA version was only been set for WPA-PSK and WPA2-PSK, but for
others it wasn't set. For AP mode this causes issues as WPA-IE is
considered and WPA3/WPA2-PSK-256 aren't allowed, they need RSN.
Explicitly set the version for all to RSN, except for WPA-PSK.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For AP we should use the security mode from the SSID as stations can
have a different security than the configure one. E.g., WPA/WPA2 in AP
vs WPA in STA1 and WPA2 in STA2.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
If the interface is in associated state, then current SSID will always
be set, so, add an early check and use SSID info freely after that.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This way we reject disconnect in AP mode and ap disable in STA mode,
though both have same functionality we treat them differently to keep
it clean.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These are to intimate the applications about connected Stations.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These events are used by AP mode, tied to AP-ENABLED and AP-DISABLED
events in the hostapd/wpa_supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These can be abstracted from the core WPA supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The management frame structure in the WPA supplicant only has a pointer,
so, it need a deep-copy before passing it to WPA supplicant, else driver
ends up freeing causing invalid memory contents.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
RSSI should only be retrieved for STA mode, but the check was wrong.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The keyword is added into array argv of wpa_cli.
The commands which require to be interactive
this keyword will allow ro print output for them.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Before starting AP mode, we don't need to search for existing networks
and join them, as the use-case is starting SoftAP.
This speeds up the AP mode operation significantly.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
RSSI is only applicable for STA mode, as for AP there are multiple
peers. This causes failure and unnecessary delay, so just skip the
retrieval.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If user enables AP mode, make sure CONFIG_AP symbol
is enabled so that access point sources get compiled etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
WPA supplicant handle is not used anymore.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This prepares for the upcoming AP mode support and moves re-usable code
to a common helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These were missed in the original support.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Instead of assuming that the array is perfectly aligned with enum, moved
to a data driven design, this decouples from the enum numbering and also
helps avoid repetition of the event string while parsing.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This is a implementation gap and shouldn't be exposed to customers.
But when we run with debug it still helps to identify any important
events that are not handled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use the newly added enumerations to translate from WPA supplicant status
codes to Zephyr Wi-Fi management status codes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use the newly added enumerations to translate from WPA supplicant status
codes to Zephyr Wi-Fi management status codes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Using "%02x" needs an unsigned integer, but all MAC addresses use
"unsigned char/char" as the data type, so, to avoid warnings, use a
temporary array.
Also, the macro from the WPA supplicant doesn't use the address of the
array element and causes warnings, so re-define the macro with address
of the element.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If the WPA supplicant internal event has a MAC address, and the sample
is compiled with newlib-nano then then the parsing fails because of lack
of support for C99 formatting options in nano [1].
Fix this by using supported specifier, even the code that encodes the
message uses the same format specifier.
[1] - https://docs.zephyrproject.org/latest/develop/languages/c/newlib.html#formatted-output
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enabling a network would trigger a scan. Since frequency is being
set after enable_network, first scan is issued without any
specific frequency.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
WPA-PSK was added a bit late, so, it wasn't properly implemented, use
both key management and protocol version to properly handle WPA-PSK in
both connection and also in the status.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
MBO and WMM-AC are mandatory for WFA certification, so cannot be
disabled for memory saving.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
wpa_supplicant has a lot of entries, and it appears in the top-level menu.
Let it be a menuconfig, so that it gets its own menu page with
all the options, instead of expanding in the top-level menu when
selected.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If a user provides both band and channel then check if they are
compatible or not.
Also, move the multiple remove network cleanup to goto.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
By default Wi-Fi works on all bands, so, the band will be unknown, in
which case no need to configure a specific frequency list to WPA
supplicant.
Only when a use provides a specific band then this is needed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This allows the WPA supplicant to build using the builtin MbedTLS.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If a specific band is configured, automatically fetch and configure the
supported channels.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For a memory constrained system, basic Wi-Fi is enough, so, add a
configuration option to compiled out advanced Wi-Fi features.
This also supports choosing individual features if needed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This should solve latency issues with using system workqueue and can now
closely implement the configured timeout.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The macro for crypto has been renamed (and as a choice), so, use the
new macro to see if the crypto has been enabled.
Fixes WPA2/WPA3 association.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This hardly saves flash but helps us in doing PSA port stagewise,
personal first and then enterprise.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to a bug in Kconfig, both legacy and PSA crypto were enabled
earlier, so, the dependencies for PSA were missed as they were provided
by legacy.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This set of changes introduces an API to set the channel when
the device is working in independent Monitor or TX injection mode
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This set of changes brings in packet filter API for Monitor and
promiscuous mode operation
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This change provides mode setting API to hostap module.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The control interface is initialized on every interface add but only
de-initialized on WPA supplicant termination. This leaks all cleanups in
the control interface dei-init.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enable the PSA key type which enables AES block cipher support.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Fix PSA dependency on random number support.
Random number generated is wanted, instead of a specific PRNG algorithm.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
We need to use PSA MbedTLS template to get entropy working.
Rather than having a single set of options which makes dependency
management tough, have a separate entry for PSA based MbedTLS which
is enabled by for NS variants only.
Also, don't use MbedTLS APIs for entropy, instead use the Zephyr APIs
that can work for both NS and S builds.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The following commits will re-introduce functionality that
the earlier commit removed, so revert the earlier commit.
This reverts commit 64423e269e.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add support for propagating SOC_NRF54LX_DISABLE_FICR_TRIMCNF and
SOC_NRF54LX_SKIP_GLITCHDETECTOR_DISABLE values to nrfx.
Signed-off-by: Magdalena Pastula <magdalena.pastula@nordicsemi.no>
- add new entries that appeared in nrfx 3.4.0
- correct the default IRQ priority value for PPR (it is intended to be
the lowest prority, so unlike for ARM cores, for RISC-V it should be
the lowest value)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Since the move to HW model v2, the MCUxpresso NXP SDK drivers got
updated during the build due to a missed rename. This caused parallel
builds and CI to become flaky.
This fixes issue #70215.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Fix TF-M support for lpcxpresso55s69 target. The following issues were
resolved:
- lpcxpresso55s69 ns defconfig did not explicitly disable
CONFIG_TRUSTED_EXECUTION_SECURE (which is set in the secure cpu0
defconfig file)
- CONFIG_TFM_BOARD was not being set correctly for the NS target
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Include into compilation the nrfx_gppi_dppi_ppib helper and related
interconnect layers when DPPIC nodes are enabled in DTS. Provide macro
definitions required by those interconnect layers based on information
from devicetree (the nrf_grtc_timer is only modified because a macro
that it uses became more generic).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add Nuvoton numaker series flash memory controller(RMC) with erase,
read & write features of soc-flash.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
This adds the minimal get_time/set_time support for the rp2040 and
enables support by default on the Pico boards. This doesn't support
configuring the clock source or alarm interrupts yet.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
For use nRF 802.15.4 Radio Driver on nRF54L series there is
necessary update for nrfx_glue.h file. It follows the pattern
used for other nRF family members.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Add support for LVGL rounder callback function. Sometimes,
either the underlying display controller and/or the LCD host
controller might impose restrictions on frame resolution.
For instance, the E1394AA65A display model should impose that
either axis of a frame be multiple of 2 pixels or the Renesas
LCD controller of the DA1469x SoC, should impose that the
stride value, number of bytes between consecutive frame lines,
be multiple of 4 bytes.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
The __WEAK-tagged function `nrf_802154_clock_hfclk_ready` is removed.
The implementation is provided by the nRF 802.15.4 Radio Driver.
Existence of __WEAK-tagged version causes incorrect behavior when
Link Time Optimization is used.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
This new version is required to handle the upcoming IPC-related DT
structure (i.e. BELLBOARD/VEVIF).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The TF-M crypto modules got renames from CRYPTO_XXX_MODULE_DISABLED to
CRYPTO_XXX_MODULE_ENABLED
Therefore also re naming it in zephyr build integration.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
QCBOR is only needed by the TF-M tests, as they are not build
separately due to the TF-M split build.
If we still set it there is a CMake build warning.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Compilation error "undefined reference to log_const_lvgl"
happened in lvgl_keypad_input.c when trying to get logs with
lvgl keypad module. Fixed by adding log level parameter
in log module macro.
Signed-off-by: Eve Redero <eve.redero@gmail.com>
Add a Kconfig option for enabling `MBEDTLS_PLATFORM_ZEROIZE_ALT`, which
is required if the mbed backend already provides an implementation.
For example, the Nordic cryptocell precompiled backends.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add nrfx configuration file to make the nrfx HAL work for
nRF54H PPR core.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Extend Kconfig definitions and nrfx_config translations so that UARTE
instances that are available in nRF54H20 can be used.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
nrf-regtool is a Python utility from Nordic Semiconductor, which is used
for generating binary files with register values for given peripherals.
It sources the descriptions of peripheral registers from CMSIS-SVD files
(typically ones bundled with nRF MDK).
For some peripherals, such as UICR, nrf-regtool supports parsing values
from devicetree as well, based on the bindings already found in Zephyr.
Currently, this tool is not submitted as a script to Zephyr, but it can
be installed from PyPI.
Having nrf-regtool installed is recommended when working with nRF54H20.
Booting the Application or Radiocore CPU requires flashing not only its
firmware, but also its respective UICR instance. On this SoC, the UICR
is used to assign ownership of global hardware resources, including
memory and peripherals, to individual cores. The Zephyr build system can
call nrf-regtool to generate the UICR based on devicetree, to reflect
the boot-time hardware configuration required for a given application.
The generated `uicr.hex` is then merged with `zephyr.hex`, so that they
can be flashed together using west.
The build system integration takes the form of a CMake package, which
includes a version check and reusable components; over time, some of
these components can be reused by sysbuild. This package is located in
the `hal_nordic` module, because it depends on the `SOC_SVD_FILE` CMake
variable, which is defined there as well.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
This CMake variable contains a path to a CMSIS-SVD file from nRF MDK,
which describes the selected Nordic SoC.
Initially, this will be used as an argument to nrf-regtool.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add nrfx and Kconfig related infrastructure plus SoC initialization
code to allow building for nRF54H20 targets (Application and Radio
cores).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Move code that prepares `NRFX_CONFIG_GRTC_*` definitions based on
information from devicetree from the nRF54L15 nrfx_config header
to the global one, so that the code can be used by nRF54H20, too.
The checks that validate owned-channels and child-owned-channels
DT properties are moved to the nrf_grtc_timer driver so that
the global nrfx_config is not polluted unnecessarily.
The default values in nrfx_config_nrf54l15_enga_application.h
are restored to those from the corresponding template file.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... to cover missing __ICACHE_PRESENT and __DCACHE_PRESENT symbols that
should be defined in MDK files.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Re-add finer grained compilation control that was lost in the CMSIS
split (#56957). CMSIS DSP is several hundred files and has a measurable
effect on compile times.
Only compiling features that are required improves this.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Adds CAN drivers for XMC4xxx SoCs.
XMC4xxx has multiple CAN nodes. The nodes share a common clock and
a message object pool.
The CAN nodes do not have a loopback mode. Instead there is an
internal bus which can be used to exchange messages between
nodes on the SoC. For this reason tests/samples which rely on the
loopback feature have been disabled.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Some crypto Kconfig options were commented out, so remove them.
These will be re-introduced later when adding crypto support
properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Compliance checker does not allow compile definitions without
a Kconfig option. So add dummy values for time being. These should
be removed at some point and replaced with properly namespaced
options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Zephyr compliance checker does not like macros that have control
structures like goto. So change the macro to align with this rule.
Also rename the macro and remove the __ prefix as it not needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Zephyr requires that the name of the variable is not the
same as the struct as seen by this warning:
modules/hostap/src/supp_api.c:64:WARNING:
Violation to rule 5.7 (Tag name should be unique)
tag: wpa_supp_api_ctrl
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If the DHCPv4 is disabled, then avoid linking warning about
missing DHCPv4 functions. Also include dhcpv4.h so that the
DHCPv4 function prototypes are found by the zephyr supplicant
driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Changed the names of the API functions between wpa_supplicant
and Zephyr upper layers. For example replaced the z_ prefix
by zephyr_ as the z_ is only meant for internal kernel
functions.
Changed the wpa_supplicant startup so that we do not poll
but wait the network interface add event which then adds
the network interfaces to the supplicant.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
There is no need to hide the wpa_supplicant interface
struct so add it directly to net_wifi_mgmt_offload struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add new files from hostap to Zephyr build.
Add wifi mgmt thread that communicates with supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Both zcbor_encode.c & zcbor_decode.c use strnlen()
In general these 2 functions are only exposed by the C library
if _POSIX_C_SOURCE is set 200809L.
But neither of these files (or their build scripts), are setting
this macro, causing build warnings
Implicit declaration of function ‘strnlen’
which turn into failures in CI with some libCs.
Let's set this macro to avoid this issue.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
`struct ieee802154_config config` is a struct containing an
union. Members of `config` were accessed incorrectly in
`otPlatRadioEnableCsl`. Fix by initializing `config` with `0`
and accessing one member at a time.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
- In `set_vendor_ie_header_lm`, case when
`link_metrics_data_len == 0` has been ignored.
This commit fixes that by setting `header_ie->length = 0`
before returning.
- current implementation of enh ACK header IE returns
`-ENOTSUP` when `ack_ie.header_ie == NULL` or
`ack_ie.header_ie->length == 0`. This commit fixes that by
refactoring checks in `nrf5_configure`.
Co-authored-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
According to PSA specification in case of `PSA_KEY_TYPE_ECC_KEY_PAIR`
function `psa_import_key` takes private key from key pair as argument.
This commit adds extraction of Private key from ECDSA key pair.
Also removes not needed `otPlatCryptoEcdsaGetPublicKey`.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
A growing number of CAN controllers do not have support for individual RX
hardware filters based on the Remote Transmission Request (RTR) bit. This
leads to various work-arounds on the driver level mixing hardware and
software filtering.
As the use of RTR frames is discouraged by CAN in Automation (CiA) - and
not even supported by newer standards, e.g. CAN FD - this often leads to
unnecessary overhead, added complexity, and worst-case to non-portable
behavior between various CAN controller drivers.
Instead, move to a simpler approach where the ability to accept/reject RTR
frames is globally configured via Kconfig. By default, all incoming RTR
frames are rejected at the driver level, a setting which can be supported
in hardware by most in-tree CAN controllers drivers.
Legacy applications or protocol implementations, where RTR reception is
required, can now select CONFIG_CAN_ACCEPT_RTR to accept incoming RTR
frames matching added CAN filters. These applications or protocols will
need to distinguish between RTR and data frames in their respective CAN RX
frame handling routines.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Platforms calculate Link Metrics values internally after using
`otPlatRadioConfigureEnhAckProbing`.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Provide properties for selected TF-M toolchain so that the NS
application will use the same toolchain as TF-M.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
The sample now builds the psa-arch-tests itself and doesn't rely anymore
on the TF-M module CMakeFile.
Additionally it will not run the zephyr main.c anymore but therefore only
uses the tf-m non-secure application.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
This removed the CMake code that builds the TF-M arch tests within the
TF-M CMakeFile. It will be moved to the tfm_integration/tfm_psa_test
sample CMakeFile.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Update the TF-M regression tests sample to build the NS app
in the tf-m-tests repository as an external project.
The regression tests need to provide test configurations to both
TF-M an NS app.
Duplicate configuration done in the spe/CMakeLists.txt to configure
TF-M image for the regression tests.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
TF-M no longer builds the NS app, but exports build files to api_ns
folder and expects the user to build the rest themselves.
Remove the option to build the NS app, and update the TFM_USE_NS_APP
to look for an output hex file in the tfm_ns folder.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Add build of the NS application in the zephyr defined out-of-tree board
support for the nordic_nrf platform.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Use TF-M PSA API headers when compiling with TF-M enabled.
Fixes: #43249
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
MbedTLS 3.5.0 requires a implementation of mbedtls_ms_time giving a
time in ms for TLS 1.3
Therefor adding an alternative implementation using zephyrs
k_uptime_get
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Update install path of tfm_ioctl_api.h, remove include of tfm_api.h
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
The TFM error codes are no longer in the interface headers.
All TF-M functions return PSA status codes, so use this here as well.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Update source lib and include path for TF-M interface files.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
The platform_ns library is no longer build with the split build anymore
so removing it.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
The place where TF-M places its non-secure api header files has changed
Therefore changing it for for all applications that use it.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
When OpenThread application is built with CONFIG_ASSERT
and CONFIG_ASSERT_NO_MSG_INFO, OT_ASSERT() prints a location
that points to the otPlatAssertFail() function instead of
the code that actually failed an assertion.
This is confusing and CONFIG_ASSERT_NO_MSG_INFO sometimes
cannot be disabled because of flash size limitations.
Make otPlatAssertFail() always print the actual assert
location.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
Remove two workarounds in OpenThread's PSA crypto backend
that were required when Zephyr used pre-1.5 TF-M version:
1. psa_open_key() is no longer needed to reference
a persistent key
2. psa_cipher_encrypt() can be used to simplify AES
encryption
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
In order to avoid build failures as described in issue #67242,
make all ST drivers using HAL_ST module dependent to HAL_STMEMSC
and HAS_STLIB libs, which need to be configured in all samples
referring to them.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds new types of keys and algorithm to crypto_psa backend
of openthread.
Added options:
- `OT_CRYPTO_KEY_TYPE_ECDSA`
- `OT_CRYPTO_KEY_ALG_ECDSA`
- `OT_CRYPTO_KEY_USAGE_VERIFY_HASH`
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
This commit implements `otPlatResetToBootloader` in two ways:
- trigger reset to bootloader using boot mode retention API
- trigger reset to bootloader by triggering GPIO pin (applicable
for nRF52840 Dongle)
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
The macro `NRF_802154_ENERGY_DETECTED_VERSION` is no longer required
because transition of nrf 802154 API is done.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
When building with CONFIG_USB_DEVICE_AUDIO, enable start of frame
notifications from the mcux sdk usb middleware
Signed-off-by: James Zipperer <jzipperer@fb.com>
Instead of using custom SoC definitions. The selected components (e.g.
CMSIS), depend on the architecture selected by the SoC Kconfig options.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Updated API version enables multi-instance GPIOTE driver.
Additionally obsolete symbol that was used to specify
API version in the past was removed.
Affected drivers have been adjusted and appropriate changes
in affected files have been made.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Added GPIOTE0, GPIOTE1 instances for legacy devices,
GPIOTE20, GPIOTE30 for Moonlight and GPIOTE130,
GPIOTE131 instances for Haltium.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Added `OT_PLATFORM_POWER_CALIBRATION` and set to always off
as in Zephyr power calibration is handled by Radio Driver.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
Remove `IEEE802154_SELECTIVE_TXPOWER` option.
Cache the tx power value in nRF5 driver and make use of it on each
operation.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
This commit adds a new Kconfig for the nRF 802.15.4 radio driver that
allows the user to specify the number of encryption keys the driver can
simultaneously store.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
There are multiple Kconfig symbols that are only available when the
radio hardware is present. As a result, the nRF 802.15.4 radio driver
is more difficult to configure on multicore architectures. Also, such
solution goes against the principle of hiding the details of the
platform behind the driver's interface.
This commit moves all the Kconfig options that correspond to settings
present in common nRF 802.15.4 configuration header so that they're
available no matter if the API is serialized.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
This commit introduces `kconfig_to_ot_option` to simply fye the way of
adding openthread related kconfigs.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Introduce possibility to override `NRFX_DIR` sybol from hal_nordic's
CMakeLists.txt file that specifies source dir for the nrfx drivers.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
The LIS2DU12 is a linear 3-axis accelerometer with advanced digital
functions whose MEMS and ASIC have been expressly designed to build
an outstanding ultralow-power architecture in which the anti-aliasing
filter operates with a current consumption among the lowest in the
market.
This driver is based on stmemsc HAL i/f v2.3
https://www.st.com/en/datasheet/lis2du12.pdf
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit replaces a magic number in the definition of serialization
ring buffer length with a macro provided by the 802.15.4 driver.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
IEEE 802.15.4-2020 defines four possible values for Key Identifier Mode
field of the Auxiliary Security Header. The current ieee802154 driver
API only supports two of them: b00 and b01. This commit adds support for
the two remaining Key Identifier Mode values. It's done by replacing a
field that can only hold Key Index into a field that can holds a pointer
to the entire Key Identifier field.
See IEEE 802.15.4-2020, sections 9.4.2.3 and 9.4.4 for further reference.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
We follow the path of the header to define the guard, aarch32 was
removed some time ago and the guards still had AARCH32 in them, just
remove it and keep the guard consistent and short.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enforce that the initial attestation partition has the required
initial attestation key provisioned.
If the initial attestation key (IAK) is not present during boot of
TF-M the system will panic during initialization.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Introduce Kconfig option in zephyr build system that reflects the TF-M
cmake config variable with the same default value for dummy provisioning
and have it satisfy the IAK present requirement.
This configuration is not suitable for production, and by having this
in zephyr configuration we can have this as part of the hardened
configuration check.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
build_info.h of mbedtls includes the config file for mbedtls but
also includes check_config.h so its not needed to have it in the
config file
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Update prompt for profile type not set, make it appear in a similar
way as the rest of the options in the choice.
Add in parethesis "base", which is how this referred to in the upstream
TF-M documentation.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Recent nRF 802.15.4 Radio Driver provides assert abstraction layer.
The assert abstraction layer is implemented in Zephyr in following
ways depending on the `NRF_802154_ASSERT_CHOICE` Kconfig choice.
`NRF_802154_ASSERT_ZEPHYR_MINIMAL` (default) gives ability to still
perform run-time checking of the nRF 802.15.4 Radio Driver operation
with minimum memory overhead and configurable behavior on fault
detection regardless of the `CONFIG_ASSERT` Kconfig option value.
`NRF_802154_ASSERT_ZEPHYR` gives ability to use asserts provided and
configurable by Zephyr including the ability to turn off the run-time
checking of the nRF 802.15.4 Radio Driver operation.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
This commit adds bbtc implementation.
New file in modules/openthread/platform/ble.c
New corresponding kconfig option `OPENTHREAD_BLE_TCAT`.
Co-authored-by: Piotr Jasiński <piotr.jasinski@nordicsemi.no>
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Signed-off-by: Piotr Jasiński <piotr.jasinski@nordicsemi.no>
This commit bumps openthread commit to `4ed44bc`
and implements `CONFIG_OPENTHREAD_MULTIPAN_RCP` option.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
The TF-M build uses the vanilla CMake FindPython3 mechanism which in
several cases misbehaves, see #24308 for details.
Ensure TF-M build uses same Python interpreter as Zephyr itself.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This change adds checks to validate consistency between Zephyr’s Kconfig
settings and cmsis configuration defined in SiP’s sdk provided headers.
This change also introduces a config to enable cmsis’ own checks which
emits warnings if a parameter relies on auto-populated default values.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Kconfig parameters, header’s default & silicon vendor’s SDK configuration
for CMSIS Core, must be consistent. Depending on the inclusion order of
the headers, this is currently not always the case.
This change introduces consistency checks & enusers defaults match their
Kconfig settings.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Switch BOARD_BL5340_DVK_CPUAPP_NS TF-M board selection from using the
platform support that is built-in to TF-M module, and instead use
the generic nRF5340 cpuapp platform support that all other nrf5340 SoC
related boards use.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The LPS28DFW is an ultracompact, piezoresistive, absolute pressure sensor.
Compared to the LPS22DF, the LPS28DFW is waterproof and has a Dual FS
capability and does not have SPI. This commit extends the LPS22DF driver to
be compatible with the LPS28DFW device.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
Nanopb generates header files that need to be available before being
included. This isn't an issue for a target where the files were added
with zephyr_nanopb_sources. But if another target wants to include
these generated files we need a cmake dependency chain.
The nanopb_generated_headers custom target been added for this purpose.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This commit is a part of introduction of new WTD instances.
It adds new Kconfig symbols that can be used in WDT shim and
nrfx driver.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
This commit increases the length of ring buffer that holds serialized
nRF 802.15.4 API calls so that it can simultaneously store all
notifications the driver is capable of issuing. Currently that's not the
case, which creates a possibility of the serialization buffers running
out while the driver is issuing notifications.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Change makes EGU instance used for anomaly 109 workaround configurable.
The default EGU instance (5) may be used for other purpose.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Regular OpenThread upmerge to commit `75694d2`.
Move CONFIG_OPENTHREAD_PLATFORM_KEY_REFERENCES_ENABLE
from header file to Kconfig.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
The Nanopb cmake locates the protoc executable, verify the result
instead of doing it ourselves.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Despite what the TF-M documentation says about SFN model not supporting
Floating Point, it does support it, according to TF-M developers.
Remove SFN limitation not supported with FP Hard ABI.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add MCUBOOT_IMGTOOL_OVERWRITE_ONLY Kconfig option which
passes the --overwrite-only option to imgtool to avoid
adding the swap status area size when calculating overflow.
It is used by non-swap update modes.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
TF-M only suports floating point in IPC model, not the SFN model.
Since floating point is a basic feature of the architecture and TF-M
has the limitation it makes more sense for the dependency to exist in
TF-M and and limit the TF-M model choice instead of limiting the
option to enable floating point.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Changes the default of `LV_Z_VDB_SIZE` to 100 percent if
`LV_Z_FULL_REFRESH` is set. Reason is that LVGL will reset the full
refresh flag if the buffer is not equal to the screen size.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Fixes an issue whereby a rename of a variable type has been
forgotten in an instance, which now uses the correct type name
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Change the default TF-M model for small profile to match the
configuration set in the profile small configuration file.
Otherwise we would be overriding the profile default.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix include order between platform_ns and tfm_api_ns libraries.
platform_ns functions may depend on tfm_api_ns.
This would typically be platform specific IOCTL services added to the
platform_ns library requiring the tfm_platform_ioctl from the
TF-M platform partition exposed in tfm_platform_api.c
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Include the zephyr/dsp/types.h header for float32_t/float64_t type
definitions to avoid conflicts with other subsystems including this header.
Add compile-time asserts to ensure the typedefs meet the requirements of
the CANopenNode module.
Fixes: #63896
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduces a Kconfig symbol `LV_Z_LOG_LEVEL` because contrary to Zephyr the
numerical value of log levels in LVGL increases with severity. Also support
for the `LV_LOG_LEVEL_USER` is added.
Resolves issue #64351.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
