This patch fixes two issues in the coordinate handling of the
`zephyr,lvgl-pointer-input` compatible:
- If the swap-xy flag is set the coordinates need to be swapped even
before the sync event is received.
- The coordinates are stored into an additional variable instead of the
pending_event. This is done to prevent the double inversion for touch
release events.
Resolves issue #70539.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Silence harmless version warning for users that have tagged TF-M.
TF-M creates a very noisy warning when you tag it:
CMake Warning at cmake/version.cmake:28 (message):
Actual TF-M version is not available from Git repository. Settled to
v2.0.0
Call Stack (most recent call first):
CMakeLists.txt:22 (include)
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Add Kconfig-to-nrfx symbol redefinitions so that TWIS instances
found on nRF54H20 and nRF54L15 devices are supported.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
SEGGER RTT module supports to use CCM for output data. This add the
necessary Kconfig option (choice).
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
This definition is used in nrfx header files, so it shouldn't be added
using `zephyr_library_compile_definitions()`. This would cause the GRTC
driver to fail the build when CONFIG_NRF_GRTC_START_SYSCOUNTER=y.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
DT nodes and compatible had been renamed and Kconfig option was relying
on the names that do not exists.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Iterate over all instances to get the information about extended
feature support in SPIM driver.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Adds the missing stubs for DMA2D kconfig symbol to fix the Kconfig warning
produced by checkpatch.
Resolves#70859
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Removing dependency on cyhal in airoc wifi driver.
It need to build airoc wifi driver with different than
PSoC 6 Soc like STM32
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Add Kconfig-to-nrfx symbol redefinitions so that PWM instances
found on nRF54H20 and nRF54L15 devices are supported.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Add nrfx_grtc related entries that were introduced in nrfx 3.4.0,
especially NRFX_GRTC_CONFIG_AUTOSTART that should be by default
set to 1.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Comment out mbedtls symbols that do not have a proper Kconfig
setting. Future commits will need to add relevant support in mbedtls
side to provided needed symbols so that they can be used in hostap
and uncomment these.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
To cater for different needs add an configuration options for WPA
supplicant network selection (scan results sorting). The default is
still left unchanged.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If user selects a band, then we should restrict scanning channels to
that band, but using freq_list will only filter the results.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make sure to copy LEN -1 bytes to the destination, to
accommodate the terminating null byte.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Even if the interface is not in connected state, allow disconnect to be
accepted, this behaviour regressed when the mode check was introduced
and if not connected then SSID will be NULL.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If MbedTLS uses its own heap which is a static heap (not libc heap),
then WPA supplicant heap usage will come down, so, reduce 8K (minimum
MbedTLS heap for Wi-Fi) from the libc heap size.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Free the deep copied data of the association response event.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Using a macro here that can potentially limit the interface name
compared to add can lead to issues, so, to mimic what we do in add, use
the sizeof with a boundary check.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These were missed earlier, and if event send fails, no point in waiting
for the state to change.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to AP-MLME being in the host and expensive computation WPA3 is not
working reliably, so, for now this is being disabled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
SAP mode adds more functionality that increases the heap usage, based on
experiments, 40000 works well to avoid startup failures.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Now that TX status buffer is allocated on heap by Zephyr driver, free
the buffer once its processed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For WPA_SUPP_CRYPTO_LEGACY, MBEDTLS_PKCS5_C is needed.
Signed-off-by: Vidar Lillebø <vidar.lillebo@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add missing MBEDTLS_PK_C dependcy for legacy crypto.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Key management for SAP should be retrieved from the network block rather
than using the per-interface global structure.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
By default (-1) libc uses all the available heap, this is good to
efficiently use the RAM, but for scenarios which there isn't enough RAM
the build will be success, but we see runtime failures.
Reserved the necessary RAM based on tests ahead to catch such scenarios,
of course this would mean that we might be no using full RAM in case
more is left, but that's never the case the with Wi-Fi :).
And this also adds the constant evaluation and fine tuneing like we do
for kernel heap and other parameters.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The timeout should be 5s, not 50s. Fix and rename the variables to
better reflect their meaning.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The code was assigning a pointer to a scoped buffer to
an object outside that scope. This would cause the driver
would receive garbage instead of a well-formatted IE and
would likely reject the IE. This in turn caused CSL IE
not being included in enhanced ACKs (verified with
wireshark).
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
When kernel stack is defined as an array, K_KERNEL_STACK_LEN()
is used to calculate the size for each stack in the array.
However, standalone kernel stack has its size calculated by
Z_KERNEL_STACK_SIZE_ADJUST() instead. Depending on the arch
alignment requirement, they may not be the same... which
could cause some confusions. So align them both to use
K_KERNEL_STACK_LEN().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
NRFX_IRQ_PRIORITY_SET is defined as empty. This causes an unused
argument warning in many callers (e.g. nrfy_gpiote_int_init). Fix it by
using ARG_UNUSED for the priority argument.
Signed-off-by: Marco Widmer <marco.widmer@bytesatwork.ch>
We will touch these lines in the next commit. Convert the comment style
to C89 instead of C99 and the indentation to tabs instead of spaces.
Signed-off-by: Marco Widmer <marco.widmer@bytesatwork.ch>
The core driver ETHOSU_LOG_SEVERITY CMake variable is a cache variable,
and thus will not be configured by the ETHOSU_LOG_SEVERITY CMake
variable of the hal_ethos_u module with local scope.
Change ETHOSU_LOG_SEVERITY local variable to be a cache var.
In addition, change condition test from LESS_EQUAL to LESS in order
to prevent an out-of-range index when accessing list variable.
Signed-off-by: Ledion Daja <ledion.daja@arm.com>
The PSA is referring to Kconfig symbols that are only found
in Nordic downstream repo so we cannot use it anyway atm.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This avoid compliance warning
Found pointless 'menuconfig' symbols without children. Use regular 'config'
symbols instead. See
https://docs.zephyrproject.org/latest/build/kconfig/tips.html#menuconfig-symbols.
WIFI_NM_WPA_SUPPLICANT modules/hostap/Kconfig:8
WIFI_NM_WPA_SUPPLICANT modules/hostap/Kconfig:8
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The big cherry-picking left some invalid code so remove/fix
it in order to pass the compilation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to a typo, channel and frequency were compared causing the
connection to fail for any combination.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Use the WPA cli command to disconnect a station in AP mode.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The WPA version was only been set for WPA-PSK and WPA2-PSK, but for
others it wasn't set. For AP mode this causes issues as WPA-IE is
considered and WPA3/WPA2-PSK-256 aren't allowed, they need RSN.
Explicitly set the version for all to RSN, except for WPA-PSK.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For AP we should use the security mode from the SSID as stations can
have a different security than the configure one. E.g., WPA/WPA2 in AP
vs WPA in STA1 and WPA2 in STA2.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
If the interface is in associated state, then current SSID will always
be set, so, add an early check and use SSID info freely after that.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This way we reject disconnect in AP mode and ap disable in STA mode,
though both have same functionality we treat them differently to keep
it clean.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These are to intimate the applications about connected Stations.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These events are used by AP mode, tied to AP-ENABLED and AP-DISABLED
events in the hostapd/wpa_supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These can be abstracted from the core WPA supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The management frame structure in the WPA supplicant only has a pointer,
so, it need a deep-copy before passing it to WPA supplicant, else driver
ends up freeing causing invalid memory contents.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
RSSI should only be retrieved for STA mode, but the check was wrong.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The keyword is added into array argv of wpa_cli.
The commands which require to be interactive
this keyword will allow ro print output for them.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Before starting AP mode, we don't need to search for existing networks
and join them, as the use-case is starting SoftAP.
This speeds up the AP mode operation significantly.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
RSSI is only applicable for STA mode, as for AP there are multiple
peers. This causes failure and unnecessary delay, so just skip the
retrieval.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If user enables AP mode, make sure CONFIG_AP symbol
is enabled so that access point sources get compiled etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
WPA supplicant handle is not used anymore.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This prepares for the upcoming AP mode support and moves re-usable code
to a common helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
These were missed in the original support.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Instead of assuming that the array is perfectly aligned with enum, moved
to a data driven design, this decouples from the enum numbering and also
helps avoid repetition of the event string while parsing.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This is a implementation gap and shouldn't be exposed to customers.
But when we run with debug it still helps to identify any important
events that are not handled.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use the newly added enumerations to translate from WPA supplicant status
codes to Zephyr Wi-Fi management status codes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use the newly added enumerations to translate from WPA supplicant status
codes to Zephyr Wi-Fi management status codes.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Using "%02x" needs an unsigned integer, but all MAC addresses use
"unsigned char/char" as the data type, so, to avoid warnings, use a
temporary array.
Also, the macro from the WPA supplicant doesn't use the address of the
array element and causes warnings, so re-define the macro with address
of the element.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If the WPA supplicant internal event has a MAC address, and the sample
is compiled with newlib-nano then then the parsing fails because of lack
of support for C99 formatting options in nano [1].
Fix this by using supported specifier, even the code that encodes the
message uses the same format specifier.
[1] - https://docs.zephyrproject.org/latest/develop/languages/c/newlib.html#formatted-output
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enabling a network would trigger a scan. Since frequency is being
set after enable_network, first scan is issued without any
specific frequency.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
WPA-PSK was added a bit late, so, it wasn't properly implemented, use
both key management and protocol version to properly handle WPA-PSK in
both connection and also in the status.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
MBO and WMM-AC are mandatory for WFA certification, so cannot be
disabled for memory saving.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
wpa_supplicant has a lot of entries, and it appears in the top-level menu.
Let it be a menuconfig, so that it gets its own menu page with
all the options, instead of expanding in the top-level menu when
selected.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If a user provides both band and channel then check if they are
compatible or not.
Also, move the multiple remove network cleanup to goto.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
By default Wi-Fi works on all bands, so, the band will be unknown, in
which case no need to configure a specific frequency list to WPA
supplicant.
Only when a use provides a specific band then this is needed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This allows the WPA supplicant to build using the builtin MbedTLS.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If a specific band is configured, automatically fetch and configure the
supported channels.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For a memory constrained system, basic Wi-Fi is enough, so, add a
configuration option to compiled out advanced Wi-Fi features.
This also supports choosing individual features if needed.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This should solve latency issues with using system workqueue and can now
closely implement the configured timeout.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The macro for crypto has been renamed (and as a choice), so, use the
new macro to see if the crypto has been enabled.
Fixes WPA2/WPA3 association.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This hardly saves flash but helps us in doing PSA port stagewise,
personal first and then enterprise.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Due to a bug in Kconfig, both legacy and PSA crypto were enabled
earlier, so, the dependencies for PSA were missed as they were provided
by legacy.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This set of changes introduces an API to set the channel when
the device is working in independent Monitor or TX injection mode
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This set of changes brings in packet filter API for Monitor and
promiscuous mode operation
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This change provides mode setting API to hostap module.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The control interface is initialized on every interface add but only
de-initialized on WPA supplicant termination. This leaks all cleanups in
the control interface dei-init.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enable the PSA key type which enables AES block cipher support.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Fix PSA dependency on random number support.
Random number generated is wanted, instead of a specific PRNG algorithm.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
We need to use PSA MbedTLS template to get entropy working.
Rather than having a single set of options which makes dependency
management tough, have a separate entry for PSA based MbedTLS which
is enabled by for NS variants only.
Also, don't use MbedTLS APIs for entropy, instead use the Zephyr APIs
that can work for both NS and S builds.
Signed-off-by: Krishna T <krishna.t@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The following commits will re-introduce functionality that
the earlier commit removed, so revert the earlier commit.
This reverts commit 64423e269e.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add support for propagating SOC_NRF54LX_DISABLE_FICR_TRIMCNF and
SOC_NRF54LX_SKIP_GLITCHDETECTOR_DISABLE values to nrfx.
Signed-off-by: Magdalena Pastula <magdalena.pastula@nordicsemi.no>
- add new entries that appeared in nrfx 3.4.0
- correct the default IRQ priority value for PPR (it is intended to be
the lowest prority, so unlike for ARM cores, for RISC-V it should be
the lowest value)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Since the move to HW model v2, the MCUxpresso NXP SDK drivers got
updated during the build due to a missed rename. This caused parallel
builds and CI to become flaky.
This fixes issue #70215.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Fix TF-M support for lpcxpresso55s69 target. The following issues were
resolved:
- lpcxpresso55s69 ns defconfig did not explicitly disable
CONFIG_TRUSTED_EXECUTION_SECURE (which is set in the secure cpu0
defconfig file)
- CONFIG_TFM_BOARD was not being set correctly for the NS target
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Include into compilation the nrfx_gppi_dppi_ppib helper and related
interconnect layers when DPPIC nodes are enabled in DTS. Provide macro
definitions required by those interconnect layers based on information
from devicetree (the nrf_grtc_timer is only modified because a macro
that it uses became more generic).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add Nuvoton numaker series flash memory controller(RMC) with erase,
read & write features of soc-flash.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
This adds the minimal get_time/set_time support for the rp2040 and
enables support by default on the Pico boards. This doesn't support
configuring the clock source or alarm interrupts yet.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
For use nRF 802.15.4 Radio Driver on nRF54L series there is
necessary update for nrfx_glue.h file. It follows the pattern
used for other nRF family members.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Add support for LVGL rounder callback function. Sometimes,
either the underlying display controller and/or the LCD host
controller might impose restrictions on frame resolution.
For instance, the E1394AA65A display model should impose that
either axis of a frame be multiple of 2 pixels or the Renesas
LCD controller of the DA1469x SoC, should impose that the
stride value, number of bytes between consecutive frame lines,
be multiple of 4 bytes.
Signed-off-by: Ioannis Karachalios <ioannis.karachalios.px@renesas.com>
The __WEAK-tagged function `nrf_802154_clock_hfclk_ready` is removed.
The implementation is provided by the nRF 802.15.4 Radio Driver.
Existence of __WEAK-tagged version causes incorrect behavior when
Link Time Optimization is used.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
This new version is required to handle the upcoming IPC-related DT
structure (i.e. BELLBOARD/VEVIF).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The TF-M crypto modules got renames from CRYPTO_XXX_MODULE_DISABLED to
CRYPTO_XXX_MODULE_ENABLED
Therefore also re naming it in zephyr build integration.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
QCBOR is only needed by the TF-M tests, as they are not build
separately due to the TF-M split build.
If we still set it there is a CMake build warning.
Signed-off-by: Markus Swarowsky <markus.swarowsky@nordicsemi.no>
Compilation error "undefined reference to log_const_lvgl"
happened in lvgl_keypad_input.c when trying to get logs with
lvgl keypad module. Fixed by adding log level parameter
in log module macro.
Signed-off-by: Eve Redero <eve.redero@gmail.com>
Add a Kconfig option for enabling `MBEDTLS_PLATFORM_ZEROIZE_ALT`, which
is required if the mbed backend already provides an implementation.
For example, the Nordic cryptocell precompiled backends.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add nrfx configuration file to make the nrfx HAL work for
nRF54H PPR core.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Extend Kconfig definitions and nrfx_config translations so that UARTE
instances that are available in nRF54H20 can be used.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
nrf-regtool is a Python utility from Nordic Semiconductor, which is used
for generating binary files with register values for given peripherals.
It sources the descriptions of peripheral registers from CMSIS-SVD files
(typically ones bundled with nRF MDK).
For some peripherals, such as UICR, nrf-regtool supports parsing values
from devicetree as well, based on the bindings already found in Zephyr.
Currently, this tool is not submitted as a script to Zephyr, but it can
be installed from PyPI.
Having nrf-regtool installed is recommended when working with nRF54H20.
Booting the Application or Radiocore CPU requires flashing not only its
firmware, but also its respective UICR instance. On this SoC, the UICR
is used to assign ownership of global hardware resources, including
memory and peripherals, to individual cores. The Zephyr build system can
call nrf-regtool to generate the UICR based on devicetree, to reflect
the boot-time hardware configuration required for a given application.
The generated `uicr.hex` is then merged with `zephyr.hex`, so that they
can be flashed together using west.
The build system integration takes the form of a CMake package, which
includes a version check and reusable components; over time, some of
these components can be reused by sysbuild. This package is located in
the `hal_nordic` module, because it depends on the `SOC_SVD_FILE` CMake
variable, which is defined there as well.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
This CMake variable contains a path to a CMSIS-SVD file from nRF MDK,
which describes the selected Nordic SoC.
Initially, this will be used as an argument to nrf-regtool.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Add nrfx and Kconfig related infrastructure plus SoC initialization
code to allow building for nRF54H20 targets (Application and Radio
cores).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Move code that prepares `NRFX_CONFIG_GRTC_*` definitions based on
information from devicetree from the nRF54L15 nrfx_config header
to the global one, so that the code can be used by nRF54H20, too.
The checks that validate owned-channels and child-owned-channels
DT properties are moved to the nrf_grtc_timer driver so that
the global nrfx_config is not polluted unnecessarily.
The default values in nrfx_config_nrf54l15_enga_application.h
are restored to those from the corresponding template file.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... to cover missing __ICACHE_PRESENT and __DCACHE_PRESENT symbols that
should be defined in MDK files.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Re-add finer grained compilation control that was lost in the CMSIS
split (#56957). CMSIS DSP is several hundred files and has a measurable
effect on compile times.
Only compiling features that are required improves this.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Adds CAN drivers for XMC4xxx SoCs.
XMC4xxx has multiple CAN nodes. The nodes share a common clock and
a message object pool.
The CAN nodes do not have a loopback mode. Instead there is an
internal bus which can be used to exchange messages between
nodes on the SoC. For this reason tests/samples which rely on the
loopback feature have been disabled.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Some crypto Kconfig options were commented out, so remove them.
These will be re-introduced later when adding crypto support
properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Compliance checker does not allow compile definitions without
a Kconfig option. So add dummy values for time being. These should
be removed at some point and replaced with properly namespaced
options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Zephyr compliance checker does not like macros that have control
structures like goto. So change the macro to align with this rule.
Also rename the macro and remove the __ prefix as it not needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Zephyr requires that the name of the variable is not the
same as the struct as seen by this warning:
modules/hostap/src/supp_api.c:64:WARNING:
Violation to rule 5.7 (Tag name should be unique)
tag: wpa_supp_api_ctrl
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If the DHCPv4 is disabled, then avoid linking warning about
missing DHCPv4 functions. Also include dhcpv4.h so that the
DHCPv4 function prototypes are found by the zephyr supplicant
driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Changed the names of the API functions between wpa_supplicant
and Zephyr upper layers. For example replaced the z_ prefix
by zephyr_ as the z_ is only meant for internal kernel
functions.
Changed the wpa_supplicant startup so that we do not poll
but wait the network interface add event which then adds
the network interfaces to the supplicant.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
There is no need to hide the wpa_supplicant interface
struct so add it directly to net_wifi_mgmt_offload struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add new files from hostap to Zephyr build.
Add wifi mgmt thread that communicates with supplicant.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Both zcbor_encode.c & zcbor_decode.c use strnlen()
In general these 2 functions are only exposed by the C library
if _POSIX_C_SOURCE is set 200809L.
But neither of these files (or their build scripts), are setting
this macro, causing build warnings
Implicit declaration of function ‘strnlen’
which turn into failures in CI with some libCs.
Let's set this macro to avoid this issue.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
