More buffers are need to build for sam_e70_xplained board
to work out of the box. Added board specific conf file.
Fixes#15096
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Patch 8af3df3519 changed logic and did not take into account 2 extra
bytes.
...
Precise data bus error
BFAR Address: 0x766e4900
***** Hardware exception *****
Current thread ID = 0x200004e8
Faulting instruction address = 0xddf4
Fatal fault in thread 0x200004e8! Aborting.
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Merge cb_usb_status_composite and cb_usb_status and use common
forward_status_cb for both composite and normal devices.
Fixes#14882
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
telnet_console driver is not compatible with new shell module, hence is
not working. Switch the telnet sample to use new TELNET shell backend.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Adding a section to the sample's documentation to give some specific
instructions on how to try it with TLS enabled. This should be helpful
for users who are not knowledgeable with regards to creating/setting up
TLS certificates.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Making a clean slate for some pylint CI tests. Only enabling relatively
uncontroversial stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add qemu ethernet driver overlays for big_http_download and
dumb_http_server samples, which are default integration samples/
tests for TCP stack. This change follows up after similar addition
of such overlays to other samples (and smsc911x overlay addition
to these samples).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Clarify what iPerf version was used when testing this sample
application. It was iPerf 2.0.9 which worked ok, for example
iPerf 2.0.13 did not work properly with UDP uploader (client)
mode.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Try to construct a proper iperf client header to the payload
as the server expects that. It is not sure if this is needed
or correct as there is no proper documentation for the iPerf2
protocol.
Fixes#14665
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Try to construct a proper iperf client header to the payload
as the server expects that. It is not sure if this is proper
way to do the iperf header as there is no documentation about
iPerf protocol anyway (except the iPerf source code).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The dhcpv4-client is more usable if it has net-shell. For testing
with qemu_x86, the e1000 overlay config is very useful.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Changing the example to not use IPv6 when it is not configured,
given IPv6 is not enabled on some platforms such as cc3220sf_launchxl.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
`CONFIG_NET_L2_BT` no longer forces required BT configuration, but
depends on a user to set a valid configuration instead. Hence, we
need to select a proper configuration in the overlay config file.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This patch adds the overlay when the echo-server is running on Linux and
echo-client is running on Qemu.
Fix: #14654
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
And also to the relevant callbacks.
That parameter is not used anywhere so it is useless.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that legacy - and unrelated - function named net_pkt_get_data has
been removed, we can rename net_pkt_get_data_new relevantly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that legacy functions are removew, let's rename the new functions by
removing the _new suffix.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The sample was bitrotted because sample.yaml was missing and no
build checks were done, so we missed the case when TCP header
API function was removed. This is now fixed by using still available
UDP header API (to get the port numbers). Also fixing debug print
as it were giving compile warnings.
Fixes#14608
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The sanitychecker needs sample.yaml in order to compile test
the promiscuous mode sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Linking to API material requires knowing the pecularities of how
doxygen, sphinx, and breathe work. In an attempt to hide some of this
we're preparing the current docs to allow use of configuration defaults
that will let us more simply use a default role that will hunt for a
reference target in the various domains that are available by using a
default "role" of "all". This will let us use the simple notation
`functionname` or `typename` without fully specifying the reference as
:c:func:`functionname`.
This patch cleans up exising docs that were (incorrectly) using single
backtics where double backtics should have been used, and also found
some typos (such as a space between the role name and the reference,
such as :file: `filename`, and a missing colon such as
c:func:`functionname`)
This is a start to address issue #14313
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
No need to build the net_pkt, just send the buffer directly.
Let's reuse already parsed ip/proto headers as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using new net_pkt r/w API and so on.
This sample would still need to be using socket API instead.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The CANBUS sockets require "struct can_frame" to be used in order to be
compatible with Linux code.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The CANBUS sockets require can_filter to be used in order to be
compatible with Linux code.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch checks the return values of setsockopt.
Fixes: #14392, #14402
Coverity-CID: 195897, 195848
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
As there is no shell submodules any more, the "zperf" command
needs to be written in every command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Patch (3206568e43) changed network
interface numbering starts from 1. The index 0 is reserved.
So use api to get default interface index for packet socket sample.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This commits adds an overlay file with the SOCKS5 symbol that is needed
to run MQTT with a proxy, and extends README with instructions on how to
use it with the default and custom settings.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The VLAN documentation had double wording and proper links to files
in github was missing, which did not look good in the rendered HTML
page.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_IEEE802154_CC2520_AUTO_ACK seems to creep back in, but has long
since be removed. We remove old references a few times.
Commit 2facf33f28 - "net: ieee802154: Remove old cc2520 AUTO_ACK
assignments".
Remove them again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds more error checking and handling for socket APIs.
Fixes: #13885
Coverity-CID: 190928
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
CONFIG_NET_DHCPV6 doesn't exist so remove references to it in the
sample, leave comments about TODO if/when this might exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CONFIG_DCD_DSR does not exist so the code block associated with it would
never be built, so remove it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Port all users of 'set_conf_file' to use the built-in rules
instead. This follows the convention-over-configuration principle to
make the system as a whole simpler and more consistent.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
If bind() fails or TX thread cannot start, then cleanup the
socket by calling close()
Coverity-CID: 191003
Fixes#13824
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We have a great number of samples now, using different port numbers,
etc. Let them be self-documenting and print out port number used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The intent of this Kconfig is to allow libc stdout
functions like printf() to send their output to the
active console driver instead of discarding it.
This somehow evolved into preferring to use
printf() instead of printk() for all test case output
if enabled. Libc printf() implementation for both
minimal libc and newlib use considerably more stack
space than printk(), with nothing gained by using
them.
Remove all instances where we are conditionally
sending test case output based on this config, enable
it by default, and adjust a few tests that disabled
this because they were blowing stack.
printk() and vprintk() now work as expected for
unit_testing targets, they are just wrappers for
host printf().
Fixes: #13701
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Follow the pattern we have for other peripherals in that if the driver
class (CAN) is enabled than enable the driver for that class
(CAN_STM32). Also have the STM32 CAN driver depend on being on a STM32
SoC.
Remove setting of CONFIG_CAN_STM32 in any .conf files as it will get set
of CONFIG_CAN is set/enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
System workqueue stack was not large enough to handle DTLS handshake,
which lead to system crash.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to follow the naming from Linux, change the name of
can_msg to zcan_frame, and can_msg_filter to zcan_filter.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add new "struct can_frame" which is compatible with Linux so that it
is easier to port socket-can applications from Linux.
Rename existing can_filter to can_msg_filter so that the name will
not conflict with Linux compatible can_filter struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add more information about DNS resolver to documentation. Move
generic DNS information from the sample application into DNS
resolver documentation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is planned to deprecate SHELL_CREATE_STATIC_SUBCMD_SET macro
which is replaced by SHELL_STATIC_SUBCMD_SET_CREATE.
Additionally, removed irrelevant comments about alphabetical
ordering which is no longer needed.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use the state machine states to determine if the session has ended.
This way zperf will properly reply stat packet to remote client even if
duration of the session is non zero.
Also we don't need to update counter (received packet number) at end of
the session.
Note: if id < 0, it means session end, otherwise it's session ongoing.
(id is the first feild of application data from remote client).
Signed-off-by: Bub Wei <bub.wei@unisoc.com>
The net-app based echo-server/client applications were used for
various smoke testing purposes. As those two apps are now removed
we need to introduce the same support into sockets based echo-client
and echo-server applications.
Fixes#13300#13481
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There are issues using lowercase min and max macros when compiling a C++
application with a third-party toolchain such as GNU ARM Embedded when
using some STL headers i.e. <chrono>.
This is because there are actual C++ functions called min and max
defined in some of the STL headers and these macros interfere with them.
By changing the macros to UPPERCASE, which is consistent with almost all
other pre-processor macros this naming conflict is avoided.
All files that use these macros have been updated.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
This application provides a full stack implementation for
communicating with the Google IOT Cloud. It leverages the
a JWT library to create JSON tokens which are then signed using
a RSA or ECDSA private key. The signed token is used to
authenticate with the Google IOT cloud servers. Once that is
accomplished, the application can subscribe, or publish data at
will.
Included in the application is a python script that can be used to
create RSA/ECDSA certificates and keys. The user will load the
certificate for the appropriate device on the Google IOT Cloud. The
private key is created by the script and stored in a C structure format
that is then consumed by the application. It is important to note that
any keys generated from the scripts SHOULD NOT BE STORED publicly.
Please refer to the README for more information.
Signed-off-by: David Brown <david.brown@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
If appropriate configuration is enabled, assume (with the default
configuration) that the proxy server uses the same address as the broker
and the default 1080 port.
The default settings can be changed in the configuration header.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
IPv4 is not needed for packet socket sample. Previous commit
helps to remove dependencies.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Sample application which opens a packet socket and receives
every packet on the wire and send some dummy packet over
socket. Simple demo of how to use packet sockets.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
As we are removing net_app and net_pkt based libraries and
applications, CoAP legacy based libraries and apps are moved
to socket based implementations. So removing legacy CoAP.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If status is 0, both ip_hdr and proto_hdr will own a pointer to the
relevant IP and Protocol headers. In order to know which of ipv4/ipv6
and udp/tcp one will need to use respectively net_pkt_family(pkt) and
net_context_get_ip_proto(context).
Having access to those headers directly, many callbacks will not need
to parse the packet again no get the src/dst addresses or the src/dst
ports. This will be change after this commit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As example of echo_async_select added recently shows, we no longer
need to define a logger unconditionally in each source file. These
samples are intended to show Zephyr compatibility with POSIX sockets
API, so the less there're differences between Zephyr vs POSIX
ifdefs, the better.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The LwM2M library has moved from the network application library
APIs to BSD socket APIs. Let's make the needed changes in the
LwM2M sample to follow those changes.
Signed-off-by: Michael Scott <mike@foundries.io>
Now that the security data can be loaded into and used from the
security / server objects, we can add support for LwM2M bootstrap.
This is a mode where initially a connection can be made to a server
which can update several LwM2M (including security and server
data) and then trigger a "bootstrap complete". Once this happens
the client will start it's connection process over but now with
the new information.
Signed-off-by: Michael Scott <mike@foundries.io>
In order to support bootstrap mode, we need to store server data
in the security / server objects. Once the connection to the
bootstrap server is made, it will clear these objects and add
new server connection data.
Signed-off-by: Michael Scott <mike@foundries.io>
As part of the migration from net_app APIs to socket APIs, let's
stop referencing the net_pkt fragments throughout the LwM2M library.
Establish a msg_data flat buffer inside lwm2m_message and use that
instead.
NOTE: As a part of this change we remove the COAP_NET_PKT setting.
The COAP library reverts to COAP_SOCK behavior.
This doesn't mean we use sockets in LwM2M (yet), it only means we
use the socket-compatible COAP library which parses flat buffers
instead of net_pkt fragments.
Signed-off-by: Michael Scott <mike@foundries.io>
Currently, this will select the needed configs for LwM2M and net_pkt.
During the migration to socket APIs, the net_pkt selections will change
to socket-based selects.
Signed-off-by: Michael Scott <mike@foundries.io>
As the net-app based echo samples are being removed, there's no use
referencing them any longer in their socket counterparts.
Additionally, overlay configuration descriptions were added in the
same manner original samples did.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit adds support in the sample to deal with the case when TLS
is offloaded and mbedtls is not necessary.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
This commit adds the necessary changes to allow the mqtt_publisher
sample to run on cc3220sf_launchxl.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The original SNTP client library was designed for the net-app API, for
which it makes sense to have a callback function, which is called
asynchronously when an answer is received.
For the socket based interface, the callback is called just before
sntp_request() returns. It gets the status and the epoch_time in
parameter, however the status is already returned by sntp_request(). It
therefore make sense to replace the callback function by a pointer to
epoch_time.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Don't include net_app.h and net_buf.h, the first is deprecated, the
latter is low-level header, both shouldn't be used for socket apps.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The WNC-M14A2A modem is supposed to use HW flow control on the UART
connected to the MCU. In the past, we were able to bypass this
requirement by using only the LTE-M firmware which supported pulling
the CTS line high via "send-ok" gpio.
This does NOT work for the LTE firmware.
Now that MCUX UART driver supports hw-flow-control setting, let's use
it in the modem overlay so that regardless of modem firmware
(LTE vs. LTE-M) the sample will "just work".
Signed-off-by: Michael Scott <mike@foundries.io>
CONFIG_NET_CONTEXT_NET_PKT_POOL is used by Zephyr's TCP stack as
a way of keeping the original packet data when compression and
other l2 specific actions make the data unusable for retries.
LwM2M uses UDP and this option was never used.
Signed-off-by: Michael Scott <mike@foundries.io>
SNTP client sample requests time sync on IPv4 and IPv6 addresses
using socket based SNTP client library.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
As networking libraries and protocols are moving to socket
based implementation, reworked SNTP client library to use sockets.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The old legacy APIs use net-app library and as that is being
removed, then the dependencies need to be removed also.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add overlays for commonly used socket samples: big_http_download and
dumb_http_server. Can be used with:
make BOARD=mps2_an385 CONF_FILE="prj.conf overlay-smsc911x.conf"
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Legacy shell removed in order to avoid maintaining two shells
systems.
All examples and tests have been migrated to the new shell.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Disabled the CONFIG_COVERAGE for benchmarks and other tests.
This is needed because it interferes with normal behavior of the
test case.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previously there was just "min_ram: 32", which took care about
suitable flash size implicitly. But now we have interesting boards
(e.g. lpcxpresso54114_m0) which tout RAM of 32K and Flash of 64K.
So, become more explicit about Flash requirement for the sample.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This builds with a host compiler, not one from the SDK, and so no
newlib library is available. There is work to enable newlib detection
at and above the cmake level. This patch can be reverted when that
lands.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When used suitable config overlay, qemu_cortex_m3 with Ethernet
support can be started with just usual "make run".
An example of such overlay is included with samples/net/echo_server,
can be built and run with:
make BOARD=qemu_cortex_m3 \
CONF_FILE="prj.conf overlay-qemu_cortex_m3_eth.conf" run
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
These were still running through Ethernet using generic
overlay-802154.conf thus creating a dedicated one.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The current OpenThread integration wants to download (from github) and
configure the OpenThread source tree every time the app is build. We
don't want to be doing this in quadruplicate every time sanitycheck is
run.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These tests were defining a "test_kw41z" case, but that platform is
already whitelisted in the main ("test") case, and this one defines no
different behavior. It's just a dupe.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix misspellings in documentation (.rst, Kconfig help text, and .h
doxygen API comments), missed during regular reviews.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Increase rx stack size for OpenThread overlay, as updated revision of
OpenThread requires more stack to operate.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Update zephyr integration of openthread to latest api as of 2018-12-17:
2a75d30684
Both echo_server and echo_client compile and are operational.
Signed-off-by: Martin Turon <mturon@google.com>
Check result of fcntl() to catch any regressions in fcntl() handling
in Zephyr. To facilitate this, also merge block() and nonblock()
functions into single setblocking().
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Current application data size in echo_client sample does not fit into a
single datagram with DTLS enbled for default IPv6 MTU (1280 bytes). This
caused abrupt failure of the sample with DTLS enabled over 802.15.4 L2.
Decreasing the application data size allows it to fit into a single UDP
datagram after encapsulating it into DTLS record.
Additionally, finetune DTLS timeout on echo_server to match UDP
application timeout on echo_client (so that a single datagram loss
does not cauase DTLS session to end).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
POSIX doesn't mandate such a header, only <fcntl.h>. <sys/fnctl.h>
is just an internal implementation detail of Newlib on which we should
not rely.
This makes it possible to build this sample against minimal libc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Considering that IP can be set dynamically by DHCP
or statically before test previously, we could have
alternative way by supporting both setting IP and
existing IP.
Signed-off-by: Bub Wei <bub.wei@unisoc.com>
Since the Arduino 101 and the Quark SE C1000 are not actively developed
boards, default to other boards that are maintained and used.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The OpenAVNU gPTP daemon repository has changed so the compile
instructions were not working.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove QEMU instructions as those do not work. Add native_posix
board instructions for running gPTP with linuxptp daemon.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This sample was creating objects from header file in the bss.
Fixed it by moving the objects to appropriate object files.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Use generic logging macros LOG_*() instead of NET_*() as the
latter are mostly meant for internal networking stack use.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove network specific default and max log level setting
and start to use the zephyr logging values for those.
Remove LOG_MODULE_REGISTER() from net_core.h and place the
calls into .c files. This is done in order to avoid weird
compiler errors in some cases and to make the code look similar
as other subsystems.
Fixes#11343Fixes#11659
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add Bluetooth, 802.15.4 and OpenThread overlay configurations to socket
echo_client and echo_server samples.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Removed printing command help from help handler. It is now
realized by the shell engine. This change saves a lot of flash
but still allows to print help in command handler with function
shell_help_print.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Removing help "options" from shell API.
Currently SHELL_OPT macro is not used by users. What is more
commit: a89690d10f ignores possible options created in
command handler by the user. As a result they are not printed
in help message.
Second, currntly implemented "options" in command handlers options are
implemented without SHELL_OPT macro.
And last but not least this change will allow to implement
help handler in a way that user will not need to think about calling
functions printing help in a command handler.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Rephrase some help messages to decrease flash usage.
Deactivate shell history feature for test test_netusb_rndis
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
We are not expecting forever k_sleep in multithreading.
And k_sleep is empty in non-multihreading.
So remove invalid forever sleep to avoid the below issue.
ASSERTION FAIL [duration != (-1)] @ zephyr/kernel/sched.c:807
Please refer to _impl_k_sleep api in zephyr/kernel/sched.c:807
Signed-off-by: Bub Wei <bub.wei@unisoc.com>
Remove adhoc handling of BLE connection setup, rely on net_config for
that. Remove board-specific configs, instead have prt.conf and overlay
configs. Perform TLS setup once before main loop, to avoid errors.
Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>
context4/6 is initilalized in net_context_get function
which is restricted under CONFIG_NET_IPV4/IPV6 with
IS_EANBLED macro. So add the same macro check for
net_context_put function to avoid NET_ASSERT(context).
Signed-off-by: Bub Wei <bub.wei@unisoc.com>
If NET_IPV6 is disabled, build issue happens as below.
zephyr/samples/net/zperf/src/zperf_tcp_receiver.c: In function ‘zperf_tcp_rx_thread’:
zephyr/samples/net/zperf/src/zperf_tcp_receiver.c:171:9: error: ‘in6_addr_my’ undeclared (first use in this function)
&in6_addr_my->sin6_addr);
^~~~~~~~~~~
zephyr/samples/net/zperf/src/zperf_tcp_receiver.c:171:9: note: each undeclared identifier is reported only once for each function it appears in
zephyr/samples/net/zperf/src/zperf_tcp_receiver.c: In function ‘zperf_tcp_receiver_init’:
zephyr/samples/net/zperf/src/zperf_tcp_receiver.c:250:3: error: ‘in6_addr_my’ undeclared (first use in this function)
in6_addr_my = zperf_get_sin6();
^~~~~~~~~~~
*** [CMakeFiles/app.dir/src/zperf_tcp_receiver.c.obj] error 1
*** [CMakeFiles/app.dir/all] error 2
Signed-off-by: Bub Wei <bub.wei@unisoc.com>
Remove an unnecessary local variable to store the
return value, instead return directly thereby saving
few bits of memory.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Update the http_get sockets sample to enable association of secure
tags with certificate filenames.
This allows certificates and keys to be provisioned to the file
system on secure flash, without having to include the actual
certificates in the application.
Validated on the cc3220sf_launchxl board.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Two separate folders and Kconfig options causing confusion on
CoAP and CoAP_SOCK implementations. This patch simplifies it.
Current CoAP Kconfig option moved to COAP_NET_PKT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The disco_l475_iot1 has the Inventek eS-WiFi, so lets enable the sample
on the board. (This also gets us something that will build test the
eS-Wifi driver as part of sanitycheck).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to prevent failing tests on i.MX RT the following samples were
limited to a minimum 140k of flash: http_client, http_server,
socket/echo_client and sockets/echo_server.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Rename existing headers and sybols to mqtt_legacy, to allow new
implementation to keep old config and header names.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Let's expand the sanity build testing for the lwm2m_client by
doing the following:
- Add variant builds for DTLS, bluetooth and modem
- Check various combinations of hardware across each of these
variant builds: frdm_k64f, nrf52_pca10040, nrf52840_pca10056,
disco_l475_iot1
Signed-off-by: Michael Scott <mike@foundries.io>
When the WNC-14A2A modem binding was originally introduced, I thought
the base_label would shorten the define keeping the result short and
easily portable. Turns out with the latest changes, it has a side
effect of removing the "DT_*" prefix which is breaking the build.
Let's remove "base_label" from the modem binding and adjust all of
the dts_fixups referring to the WNC14A2A defines.
NOTE: This commit moves the left-over WNC14A2A dts_fixup defines from
the nRF52 soc into samples/net/lwm2m_client as the new values.
They will stay there until the modem can be re-configured as a shield.
Signed-off-by: Michael Scott <mike@foundries.io>
During the modem overlay move from the K64F board directory to the
LwM2M sample code, 2 DTS entries were dropped:
current-speed = <115200>;
status = "ok";
Without these entries the DTS defines for UART2 and CURRENT_SPEED
are missing from the generated_dts_board.h file.
Signed-off-by: Michael Scott <mike@foundries.io>
The wncm14a2a modem is an add-on/shield and not part of the
nrf52840_pca10056 board and should be maintained and configured
outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
echo_server can use up to 6 sockets therefore it needs more file
descriptors than the maximum default value specified.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Change the sample to use a different controller device name per pin. We
shouldn't assume that on a given board that all the pins we are using
will be on the same GPIO controller device.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a dts binding for the Atmel WINC1500 WIFI chip. Update the
quark_se_c1000_devboard to utilize this binding as well as the wifi
sample app.
We now get all the GPIOs related to the Atmel WINC1500 from the device
tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a shell that implements "promisc [on | off] <interface>"
command to toggle promiscuous mode support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Couple of findings which were revealed after changing
LOG_MODULE_REGISTER macro:
- missing semicolons after LOG_MODULE_REGISTER()
- missing LOG_LEVEL defines
- other
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The overlay-e1000.conf can be used for example with Qemu
which has support for e1000 ethernet driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This required wiring external daughter board by hand, it's not provided
by the board directly, let's remove this.
Applying the change on relevant samples.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is an mcr20a shield board for frdm_k64f which is easier to use
than wiring a cc2520 by hand. So let's remove this.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Issue found using Coccinelle. Semaphore is not required at all
in this application.
Fixes#11150
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Improved RX path to use ring buffer for incoming data instead of single
byte buffer. Improved TX path to use ring buffer. Added support for
asynchronous UART API (interrupts).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Tweak ROM usage of quark_se_c1000_devboard so that test_usbnet
test will pass. The board just disables network statistics as
that is not really needed here.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The task_profiler is not needed nor used by zperf so remove
it from CMakefile.
Fixes#11051
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Unify the function naming for various network checking functions.
For example:
net_is_ipv6_addr_loopback() -> net_ipv6_is_addr_loopback()
net_is_my_ipv6_maddr() -> net_ipv6_is_my_maddr()
etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move configuration to overlay-netusb.sonf, enable zero-configuration,
working with LLMNR in Windows and avahi-autoipd in Linux.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
This updates documentation to account for the new shell which
does not support 'select' for command context anymore.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The wifi shell sample asserts when trying to do a sleep
forever.
The sleep should not be necessary, so removing it.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The "zperf udp download" optional port parameter was not properly
checked, the default port check branch was never reached.
Fix also the same issue in tcp download command.
Coverity-CID: 188881
Fixes#10758
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the default behaviour of the host network interface
setup. Now user needs to execute net-setup.sh script from
net-tools project to setup host ethernet interface. The script
needs to be run as a root user. Then zephyr.exe can be started
as a normal user.
Example:
cd net-tools
sudo ./net-setup.sh
This will create zeth network interface and set IP address and
routes properly. See other command line options by typing
./net-setup.sh --help
Old behaviour is still there if one enables
CONFIG_ETH_NATIVE_POSIX_STARTUP_AUTOMATIC=y
in which case one needs to use the command
sudo --preserve-env zephyr.exe
to start the Zephyr process.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The existing API defined sys_clock_{hw_cycles,ticks}_per_sec as simple
"variables" to be shared, except that they were only real storage in
certain modes (the HPET driver, basically) and everywhere else they
were a build constant.
Properly, these should be an API defined by the timer driver (who
controls those rates) and consumed by the clock subsystem. So give
them function syntax as a stepping stone to get there.
Note that this also removes the deprecated variable
_sys_clock_us_per_tick rather than give it the same treatment.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Remove redundant 'sample' tag and add something that matches the
functionality and features being tested, demonstrated.
Avoid short abbriviations and using full names for fs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
ROM consumption is higher with new shell which prevents
quark_se_c1000_devboard from building. Remove that board
from sanitychecker runs.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use new shell instead of the legacy one. This commit also fixes
the configuration file mess and allows the program to be run on
more hardware.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There were no shell commands implemented so remove the shell
support from this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Removed obsolete CONFIG_SYS_LOG_* and CONFIG_NET_DEBUG_* options
from various sample and test applications.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The conf file contained obsolete config options and it was
not really used. Cleaned also the sample.yaml file.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previously, wifi-enabled samples were not built by sanitycheck for the
cc3220sf_launchxl.
This patch gets the sockets echo sample to build.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Also, defines one LOG_MODULE_NAME for the simplelink WiFi driver, and
uses the same name for all files in this driver (module).
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The $srctree environment variable gives the path relative to which
'(o)source' statements work (the current directory is used if $srctree
is unset). It is set to $ZEPHYR_BASE in cmake/kconfig.cmake, so there's
no need to qualify the source of Kconfig.zephyr in sample Kconfig files
(or in external projects).
All 'source's in Zephyr assume that the Zephyr root directory is used as
the srctree as well, and would break otherwise.
Remove the $(ZEPHYR_BASE)s to make it clearer that all 'source'
statements work relative to the Zephyr root. There was some user
confusion on IRC.
Also explain how things work in the documentation.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
usb_dc_status_callback() parameters are interface or configuration
numbers and should be const.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Decrease number of buffer for sanity check, in real sample logs
consuming a lot of memory might be traded for buffers. The sample was
failing for quark_se_c1000_devboard.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
As the sample.yaml file was missing, then sanitychecker did
not testing any wifi drivers or other wifi related APIs.
Fixes#10389
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the debugging print calls are async, all the strings that might
be overwritten must use log_strdup() which will create a copy
of the printable string.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The application won't work anymore as it uses the old syslog
logging and networking is now converted to use the new logger
so there is no need for this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "openthread" tag for sanitychecker when it is running
OpenThread specific tests. This way it is easier to run just
those few OpenThread specific tests.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With recent changes, sockets no longer depend on Newlib libc, so
let's have actual samples which demonstrate this. echo_client/
echo_server, which were ported from net_app samples, are converted.
The rest of socket samples are intended to be buildable on a
POSIX system (e.g. Linux), so they rather stay with more
full-fledged libc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Unify method of enabling secure TLS sockets in samples by using TLS
overlay config file instead of standalone config files.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Avoid having not-necessarily board specific configs in a separate file.
Instead, have a single project file with appropriate overlay configs.
Board specific configurations can be added in future if needed.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
It is no longer necessary to set the KCONFIG_ROOT variable when the
KConfig file is in the application root directory.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
If user enables VLAN support, then the sample application will
create two extra VLAN network interfaces for testing purposes.
The application can be compiled like this for VLAN support:
cmake -DBOARD=qemu_x86 -DOVERLAY_CONFIG=overlay-vlan.conf ..
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for VLANs which are disabled by default.
The application can be configured to use the VLANs by setting
the IP addresses properly in config file. The VLAN support in
this sample application is only meant for testing multiple network
interface handling.
The application can be compiled like this for VLAN support:
cmake -DBOARD=qemu_x86 -DOVERLAY_CONFIG=overlay-vlan.conf ..
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for VLANs which are disabled by default.
The application can be configured to use the VLANs by setting
the IP addresses properly in config file. The VLAN support in
this sample application is only meant for testing multiple network
interface handling.
The application can be compiled like this for VLAN support:
cmake -DBOARD=qemu_x86 -DOVERLAY_CONFIG=overlay-vlan.conf ..
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user enables VLAN support, then the sample application will
create two extra VLAN network interfaces for testing purposes.
The application can be compiled like this for VLAN support:
cmake -DBOARD=qemu_x86 -DOVERLAY_CONFIG=overlay-vlan.conf ..
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
New shell implementation is on the way. For now old one and all
references are kept to be gradually replaced by new shell.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
With the new Kconfig preprocessor (described in
https://github.com/torvalds/linux/blob/master/Documentation/kbuild/
kconfig-macro-language.txt), the syntax for expanding environment
variables is $(FOO) rather than $FOO.
$(FOO) is a general preprocessor variable expansion, which falls back to
environment variables if the variable isn't set (like in Make). It can
also be used in prompts, 'comment's, etc.
The old syntax will probably be supported forever in Kconfiglib for
backwards compatibility, but might as well make it consistent now that
people might start using the preprocessor more.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add a prj conf file for the TI cc3220sf_launchxl board
to enable socket offload to the simplelink WiFi driver.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Refactor IPv6 address lifetime timer setting in net_if_addr to support
longer lifetime than 24 days.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This removes these network sample applications
samples/net/coaps_client
samples/net/coaps_server
as they are using low level mbedtls APIs. You should use
preferably socket based or net-app based applications.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Payload variable can hold max 64 bytes but value of size can be more
than that. Memsetting using value of size can overrun payload array.
Fixes coverity issue.
Coverity-CID: 187823
Fixes: #9638
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This removes these network sample applications
samples/net/mbedtls_sslclient
samples/net/mbedtls_dtlsserver
samples/net/mbedtls_dtlsclient
as they are using low level mbedtls APIs. You should use
preferably the samples/net/sockets/echo_[server|client] applications
instead, or as a last option use net-app based applications
in samples/net/echo_[server|client] if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Due to a change in the company name, the LwM2M copyrights need
to be changed from "Open Source Foundries Limited" ->
"Foundries.io".
Signed-off-by: Michael Scott <mike@foundries.io>
Per: http://pubs.opengroup.org/onlinepubs/009695399/functions/socket.html
"Upon successful completion, socket() shall return a non-negative
integer, the socket file descriptor."
The test in prepare_fds() however fails if socket fd is
zero (non-negative), which should be a valid value.
This was found while testing the SimpleLink socket offload driver,
which can return a zero-valued socket fd, per the POSIX spec.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Move to more generic tracing hooks that can be implemented in different
ways and do not interfere with the kernel.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit contains several fixes for DTLS implementation, proposed in
a post-merge review of #9338.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Instead of having one delayed_work struct / IP address, use
only one delayed_work struct for lifetime timer. This saves
over 20 bytes / allocated address struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Prepend the text 'cmake_minimum_required(VERSION 3.8.2)' into the
application and test build scripts.
Modern versions of CMake will spam users with a deprecation warning
when the toplevel CMakeLists.txt does not specify a CMake
version. This is documented in bug #8355.
To resolve this we include a cmake_minimum_required() line into the
toplevel build scripts. Additionally, cmake_minimum_required is
invoked from within boilerplate.cmake. The highest version will be
enforced.
This patch allows us to afterwards change CMake policy CMP000 from OLD
to NEW which in turn finally rids us of the verbose warning.
The extra boilerplate is considered more acceptable than the verbosity
of the CMP0000 policy.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This finishes refactor of splitting off net_config library name from
net_app library, started in c60df1311, c89a06dbc. This commit makes
sure that Kconfig options are prefixed with CONFIG_NET_CONFIG_
instead of CONFIG_NET_APP_, and propagates these changes thru the
app configs in the tree.
Also, minor dependency, etc. tweaks are made.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add DTLS support to socket echo_client and echo_server samples.
Additionally, move TLS-related configs to overlay-tls.conf config file,
to align with other examples.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This will make adding properties to symbols in the base Zephyr Kconfig
files work the same as before.
I didn't actually spot any such cases, so this is just to play it safe.
It also makes the sample Kconfig symbols appear at the top in the
menuconfig interface, which might be nice.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These are no longer required. Kconfiglib expands references to
environment variables directly.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Some reST syntax errors and doc edits got missed during the review
of PR #561 causing problems in the generated HTML.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The application does nothing useful, it just enables Link Layer
Discovery Protocol support which starts to send LLDP network packets
to ethernet network interface. Note that the LLDP packets are only
sent to those network interfaces that claim to support LLDP.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
- Remove NET_LOG / NET_BUF_LOG settings, instead just enable SYS_LOG
- Simplify by also removing SYS_LOG_SHOW_COLOR, INIT_STACKS and
NET_STATISTICS. These can be enabled by user if wanted/needed.
Signed-off-by: Michael Scott <mike@foundries.io>
Allow user to configure a program that is executed after the
network interface is created and IP address is setup.
This can be used e.g., to start wireshark to capture
the network traffic of the interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Default value 2 was not enough for mcast addresses table.
Core stack adding mcast addresses on various reasons. Also
coaps_client trying to create mcast context for some purpose.
mcast address is not in lookup table, so binding fails. Add
CoAP sample related mcast address to table and then bind the
context.
Fixes#9131
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Let's add an overlay file to enable using the WNC-M14A2A LTE-M
modem with the LwM2M client.
Also, update documentation for it's use.
Signed-off-by: Michael Scott <mike@foundries.io>
Adding IPv4 autoconf sample application that can be used to
test IPv4 autoconf functionality.
Signed-off-by: Matthias Boesl <matthias.boesl@gmail.com>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This app will not fit in the 96b_nitrogen board with ECC enabled.
"real-ld: region `SRAM' overflowed by 68 bytes". Disable the feature
explicitly since a subsequent patch will auto-enable it for all
combined Bluetooth Host-Controller builds.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Thread registers multiple unicast and multicast adresses by default. As
they are exchanged with Zephyr interface, we need enough buffers to
store them all.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit adds TLS support to socket echo_client/echo_server samples.
Credentials used are the same as in the non-socket versions of these
samples, therefore they can be easily tested with net-tools utils.
Maximum payload size for the client was sligtly reduced to fit the
encrypted data within 1280 bytes.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add CA certificates to http_get and big_http_download samples. Use
socket options to configure TLS connection - TLS certificates are now
validated.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Refactor the prj*conf files so that there is only one master
prj.conf and several overlay conf files that add / change
only minor subset of functionality.
Use the overlay files like so:
cmake -DBOARD=nrf52840_pca10056 \
-DOVERLAY_CONFIG=overlay-ot.conf ..
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The logic for error checking after net_pkt_pull was inverted -
build_pkt_reply would exit in case net_pkt_pull succeeded. In result no
responses were sent by echo_server.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
If -fno-strict-overflow compiler flag is disabled, then this warning
is printed:
samples/net/throughput_server/src/server.c:157:6: \
error: assuming signed overflow does not occur when assuming \
that (X + c) >= X is always true [-Werror=strict-overflow]
if (new_print > curr) {
Fixes#8924
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor the prj*conf files so that there is only one master
prj.conf and several overlay conf files that add / change
only minor subset of functionality.
Use the overlay files like so:
cmake -DBOARD=nrf52840_pca10056 \
-DOVERLAY_CONFIG=overlay-ot.conf ..
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If echo-server receives a IPv6 packet with large header (e.g HBHO)
build_reply_pkt() function failed to remove IPv6 header. Reason is
net_buf_pull() doesn't work if header length is more than one
fragment. net_pkt_pull() solves the issue.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Fixing copy paste error, where ipv4 member of
the structure is used in ipv6 branch.
CID: 187074
Fixes Issue #8992
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
On some architectures tick time cannot be expressed as integer
number of microseconds, introducing error in calculations using
sys_clock_us_per_tick variable.
This commit deprecates the sys_clock_us_per_tick variable and
replaces its usage by more precise calculations based on
sys_clock_hw_cycles_per_sec and sys_clock_ticks_per_sec.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
With the change to the configuration files, we can now compile
this sample for any platform that uses only the default prj.conf file:
nrf52840_pca10056
nrf52840_pca10059
usb_kw24d512
Update the sample.yaml file to remove the excludes.
Signed-off-by: Michael Scott <mike@foundries.io>
Let's rename README to README.rst and add:
- Some nice formatting for existing content
- Requirements section (including handy links)
- Build and Running section (including multiple overlay options)
Signed-off-by: Michael Scott <mike@foundries.io>
Add support for NXP MCR20A 802.15.4 module as an overlay config file.
Use this file like so:
cmake -DBOARD=usb_kw24d512 \
-DOVERLAY_CONFIG=overlay-mcr20a.conf ..
Signed-off-by: Michael Scott <mike@foundries.io>
Add support for TI CC1200 802.15.4 module as an overlay config file.
Use this file like so:
cmake -DBOARD=quark_se_c1000_devboard \
-DOVERLAY_CONFIG=overlay-cc1200.conf ..
Signed-off-by: Michael Scott <mike@foundries.io>
When the CC2520-specific configs are removed from the prj.conf
file, the sample can be built for hardware that supports
802.15.4 natively w/o any changes to the prj.conf like so:
cmake -DBOARD=nrf52840_pca10056 ..
cmake -DBOARD=usb_kw24d512 ..
The CC2520-specific settings now live in overlay-cc2520.conf
which can be used like so when building for devices that can
use it:
cmake -DBOARD=quark_se_c1000_devboard \
-DOVERLAY_CONFIG=overlay-cc2520.conf ..
Later, support for other optional HW like CC1200 and MCR20A
can be added in a similar way.
Signed-off-by: Michael Scott <mike@foundries.io>
ESP32 does not like newlib, exclude for now to get a clean sanitycheck
run. We have issues about this already.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add config file that enables to run http_get and big_http_download
samples with TLS enabled and receive the data through HTTPS.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
If we use newlib the isdigit (and other similar functions) return an
error as char can possibly be viewed as signed:
usr/include/ctype.h:57:54: error: array subscript has type ‘char’ [-Werror=char-subscripts]
#define __ctype_lookup(__c) ((__ctype_ptr__+sizeof(""[__c]))[(int)(__c)])
Explicity cast to unsigned char so we deal with both this warning and
possible warning when -Wpointer-sign is enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current config files for TLS qemu_x86 contain unrecognized
`CONFIG_RAM_SIZE`, which causes cmake to fail during project generation.
They should not be needed anyway, as qemu_x86 defaults to 8 MB of RAM.
Additionaly, echo_client crashes in this configuration with default main
stack size, hence increase it.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Allow gPTP code to be run as a linux process and communicate
with gPTP daemon running in linux host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
By default gPTP is not run over VLAN but if needed that can be
done by setting CONFIG_NET_GPTP_VLAN and CONFIG_NET_GPTP_VLAN_TAG
options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This allows zephyr to listen LLMNR DNS queries sent by Windows
and respond to them. See RFC 4795 for details.
The feature requires that hostname is set properly to the
zephyr device and LLMNR is configured properly.
Typically following config options are enough for this support:
CONFIG_NET_HOSTNAME_ENABLE=y
CONFIG_NET_HOSTNAME="zephyr-device"
CONFIG_DNS_RESOLVER=y
CONFIG_LLMNR_RESPONDER=y
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
