These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This shell command was tied to bluetooth and the bluetooth shell and
also had messages all related to nordic ICs.
Make it generic and put it under drivers/flash/ so it can be included by
anyone and independently of bluetooth.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These devices increase the page size from 2k (standard STM32L4) to 4K,
so we must account for this.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Under GNU C, sizeof(void) = 1. This commit merely makes it explicit u8.
Pointer arithmetics over void types is:
* A GNU C extension
* Not supported by Clang
* Illegal across all ISO C standards
See also: https://gcc.gnu.org/onlinedocs/gcc/Pointer-Arith.html
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Use a lower slot duration than the used erase slot duration
to speed up the interval of write operations when in sync
with active Bluetooth connections.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
irq_lock returns an unsigned int, though, several places was using
signed int. This commit fix this behaviour.
In order to avoid this error happens again, a coccinelle script was
added and can be used to check violations.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Up until now, Zephyr has patched Kconfig to use the last 'default' with
a satisfied condition, instead of the first one. I'm not sure why the
patch was added (it predates Kconfiglib), but I suspect it's related to
Kconfig.defconfig files.
There are at least three problems with the patch:
1. It's inconsistent with how Kconfig works in other projects, which
might confuse newcomers.
2. Due to oversights, earlier 'range' properties are still preferred,
as well as earlier 'default' properties on choices.
In addition to being inconsistent, this makes it impossible to
override 'range' properties and choice 'default' properties if the
base definition of the symbol/choice already has 'range'/'default'
properties.
I've seen errors caused by the inconsistency, and I suspect there
are more.
3. A fork of Kconfiglib that adds the patch needs to be maintained.
Get rid of the patch and go back to standard Kconfig behavior, as
follows:
1. Include the Kconfig.defconfig files first instead of last in
Kconfig.zephyr.
2. Include boards/Kconfig and arch/<arch>/Kconfig first instead of
last in arch/Kconfig.
3. Include arch/<arch>/soc/*/Kconfig first instead of last in
arch/<arch>/Kconfig.
4. Swap a few other 'source's to preserve behavior for some scattered
symbols with multiple definitions.
Swap 'source's in some no-op cases too, where it might match the
intent.
5. Reverse the defaults on symbol definitions that have more than one
default.
Skip defaults that are mutually exclusive, e.g. where each default
has an 'if <some board>' condition. They are already safe.
6. Remove the prefer-later-defaults patch from Kconfiglib.
Testing was done with a Python script that lists all Kconfig
symbols/choices with multiple defaults, along with a whitelist of fixed
symbols. The script also verifies that there are no "unreachable"
defaults hidden by defaults without conditions
As an additional test, zephyr/.config was generated before and after the
change for several samples and checked to be identical (after sorting).
This commit includes some default-related cleanups as well:
- Simplify some symbol definitions, e.g. where a default has 'if FOO'
when the symbol already has 'depends on FOO'.
- Remove some redundant 'default ""' for string symbols. This is the
implicit default.
Piggyback fixes for swapped ranges on BT_L2CAP_RX_MTU and
BT_L2CAP_TX_MTU (caused by confusing inconsistency).
Piggyback some fixes for style nits too, e.g. unindented help texts.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds support for configuring the CS toggling delay and using a
different device ID so that compatible flash chips can also be
used by this driver.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdtech.com>
When using CONFIG_MULTITHREADING=n, the semaphore primitives are
non-functional and useless. Remove their usage when this option is
enabled.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
When using CONFIG_MULTITHREADING=n, the semaphore primitives are
non-functional and useless. Remove their usage when this option is
enabled.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
CONFIG_SPI_FLASH_W25QXXDV_MAX_DATA_LEN is a left-over from old SPI API
usage. Now, there is no limit (besides the flash size) in SPI data
transaction.
Fixes#8327
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The old way of erasing was not completely moved to the new SPI access
function, thus always sending useless dummy bytes that could lead to
error (aka: erasing more than requested).
Fixes#8065
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The various macros to do checks in system call handlers all
implictly would generate a kernel oops if a check failed.
This is undesirable for a few reasons:
* System call handlers that acquire resources in the handler
have no good recourse for cleanup if a check fails.
* In some cases we may want to propagate a return value back
to the caller instead of just killing the calling thread,
even though the base API doesn't do these checks.
These macros now all return a value, if nonzero is returned
the check failed. K_OOPS() now wraps these calls to generate
a kernel oops.
At the moment, the policy for all APIs has not changed. They
still all oops upon a failed check/
The macros now use the Z_ notation for private APIs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the driver files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Driver APIs might not implement all operations, making it possible for
a user thread to get the kernel to execute a function at 0x00000000.
Perform runtime checks in all the driver handlers, checking if they're
capable of performing the requested operation.
Fixes#6907.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The sam0 flash driver has support for retrieving flash page layout
information. This commit fixes compilation when
CONFIG_FLASH_PAGE_LAYOUT is disabled.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
- There is a mismatch when interfacing with external code where a
uint32_t is defined as a parameter and internal Zephyr code attempts
to use u32_t. If NewLib is used, the typedef for u32_t is
'unsigned int' which is not a portable match to uint32_t as
'unsigned int' is not a common size across architectures so gcc will
output a warning.
- The mcux flash code calls NXP supplied functions that expect a
uint32_t.
- openthread.c ot_state_changed_handler has a uint32_t flag as a
parameter.
Signed-off-by: David Leach <david.leach@nxp.com>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
STM32F0 flash driver already uses FLASH_PAGE_SIZE from HAL
in flash layout part, so CONFIG_FLASH_PAGE_SIZE is redundant
and confusing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Keyword FLASH_HAS_PAGE_LAYOUT is related to flash and should
be declared in its Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
It was possible to have enable flash module while no flash driver
implementation was enabled. This cause coverity issues and unnecessary
initialization call.
This pat introduce FLASH_HAS_DRIVER_ENABLED Kconfig keyword which is
selected once any flash driver is enabled. flash_map switch its
dependency to this keyword.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Fix Coverity "Memory - corruptions (ARRAY_VS_SINGLETON)"
issue by type casting word_to_write to u8_t pointer and
adding a length check before memcpy operation.
Coverity CID: 182779
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Fixed incorrect comparison of FLASH_SLOT in microseconds
with ticks elapsed.
This caused Bluetooth controller to try scheduling events
beyond the acceptable soft real-time design limits, due to
the CPU halted for flash erase operation.
Fixes#6229.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor ticker execution context dependency out into HAL
folder. This decouples ticker from mayfly, enabling porting
towards a more tasklet (if and when kernel gets the support)
style execution contexts type implementation support.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Write protection is currently not supported by the mcux flash
driver. This prevents it from working with the DFU subsystem, which
checks the error codes from the write protect routine. Hack it for now
with a semaphore.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Add Altera Nios-II QSPI Flash controller driver which has
has 1024 blocks or sectors wich each sector size being 64K bytes.
This driver supports flash erase, write, read and lock operations.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Uses the new flash erase-block-size dts property to implement the flash
page layout api in the mcux flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We want to move to use a common FLASH_DEV_NAME across the various flash
drivers. So samples, tests, or other code can be a bit more generic. So
replace CONFIG_SOC_FLASH_NRF5_DEV_NAME with FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
In flash driver init, write_block_size could be initialized
with FLASH_WRITE_BLOCK_SIZE which is generated from device
tree parsing (dts property: "write-block-size")
Fixes#5305
If not defined, generate a compilation error.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The SAM0 has a 64 byte page (the programing unit) with 4 pages to a
row (the erase unit). This driver implements a read/modify/write to
emulate the byte level writes used by NFFS.
Signed-off-by: Michael Hope <mlhx@google.com>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some drivers doesn't implement flash API page layout extension
which is causing the application crash once the API was calling.
This patch introduce system termination for this in those drivers
which doesn't implement extension. This will help to discover this
problem early.
It is not done by preprocessor check because it is possible to have
enabled a driver which support and a driver which doesn't support
this API simultaneously.
Now FLASH_PAGE_LAYOUT configuration option is accessible only in case
that at last one driver which implements mentioned API is enabled.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add the STM32F0 Embedded Flash support in the flash_stm32 driver
interface.
The STM32F0 has a particularity or use the HSI as clock source
for the flash controller interface, so this clock must be
enabled directly in the case HSE or another clock is used by
the system clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch makes minor improvements to the flash documentation:
* spi -> SPI
* Capitialise the first word in a sentance
* Adding the, and, all, etc where appropriate.
Signed-off-by: Michael Hope <mlhx@google.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
The page_layout API returns pointers to kernel memory and is not
exposed to user mode. This is fine for flash_get_page_count()
and flash_get_page_info APIs since these copy the values, but some
redesign work will be needed to get flash_page_foreach() working in
user mode since we do not want the callback running in a privileged
state.
Due to the way that (even unimplemented) system call prototypes are
generated, the definition of struct flash_pages_info needed to be
moved outside of the #ifdef.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When the header file is located in the same directory as the source
file it is better to use a relative quote-include, e.g.
than a system include like
Avoiding the use of system includes in these cases is beneficial
because;
* The source code will be easier to build because there will be fewer
system include paths.
* It is easier for a user to determine where a quote-include header
file is located than where a system include is located.
* You are less likely to encounter aliasing issues if the list of
system include paths is minimized.
Authors:
Anas Nashif
Sebastian Bøe
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
`rc` gets assigned values from function returning `int` and not
`u32_t`.
Fixes#4051.
Coverity-ID: 177219
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Write-block-size values were filled for nRF5, STM32, QMSI, MCUX and
w25qxxdv devices.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
This patch adds a routine which can be used to iterate over all flash
pages on the device.
This can be also done by using flash_get_page_info_by_idx(), but that
would add an unnecessary loop over the layout array for each page.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
L4 parts have a constant page size, so just rely on the HAL defines
that provide it, along with a read to the register which contains this
SoC's total size.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Add flash page layout support for STM32F4 SoCs.
This almost eliminates the need for flash_map.h, except for
STM32F4X_SECTOR_MASK, so delete the file and move the define into the
F4 implementation, to keep things simple.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This is a prep work commit for adding flash page layout support.
The internal flash APIs for STM32 on L4 and F4 are a bit
inconsistent. Some routines take a pointer to the private data, others
don't. Those that do take it as a last argument instead of a
first. Additionally, some APIs are declared in flash_stm32.h that
aren't ever used by the family-specific files.
Clean this up by making everything take a struct device*, and marking
routines static in the common driver code when possible.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Added an internal function to obtain the flash page layout in
run-length encoded format. The API is simple and allows the actual
public API implementations to be simple and maintainable.
This feature can be enabled by using the FLASH_PAGE_LAYOUT Kconfig
option. This API is required for the implementation of flash file
system.
Added a public API to get flash page information (size and start offset)
by offset within the flash and by index of the page.
Added a generic implementation of the internal flash_get_page_info API.
Added an additional public API call to get the total count of pages in
the flash memory and its generic implementation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
data_addr is not guaranteed to be word-aligned so we need to read it in
a safe way, otherwise this can trigger hardfault on nRF51.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
ll_radio_state_is_idle() returns bool, not an error value - this means
it is non-zero on success.
Jira: ZEP-2445
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
L4 write access requires 64 bits alignment
while L4 read access does not require any alignment.
To support specific check according to read/write,erase
a parameter is added to stm32_valid_range.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
L4 have 64 bits write access.
The cast to 64 bits data address in write_dword
requires 3 right shifts on i (byte index) else the
data taken are wrong for i different from 0
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
A typo was present ion the erase and write function were bit were
uncorrectly unset but all other bit except the mask were unset.
The code still worked because the two typos fixed themselves.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Requesting a flash_write with a length of 0 results in a flash
position being written. Instead we should return 0 unless there is
some other input parameter that is invalid.
Change-Id: Ife6e6e2314bbee2bde7d0b69db3122ca00c361e0
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
After activation of cube based driver support on L4 and F3 series,
this commits performs the clean up of F3 and L4 relative code to
native clock control drivers.
Indirectly, it makes pwm driver supported de facto on F3 series
Change-Id: Idac17103a9b5ef6eab540719343cc8f5865f15fa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32f3xx flash driver to support it.
Clean up will be done afterwards.
Change-Id: I3260bb063f714fa29adbc71d8036f20479a99b34
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit removes unnecessary CONFIG_SYS_POWER_DEEP_SLEEP protection
in shim drivers as QMSI 1.4 has introduced empty context save/restore
functions that can be called in Quark D2000, therefore keeping common
code at the shim driver level for Quark SE and D2000.
Change-Id: Ia2a466327f999668c6511c0193014e9151bff6ae
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
This is one the series patches that simplifies the driver code by
using the IS_ENABLED macro. This removes the need of the const
variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I59802cf9f482337656b0fdc4b272f3b1ddc6cbda
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
The newer version of mcux changes its flash api slightly, so update the
Zephyr shim accordingly.
Change-Id: I0c974fc3e82b9f40372c636f0b805ed143be2198
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add spi flash erase boundary check. The erase boundary must be
4K-aligned. So, the flash chip will round down an non-4K aligned
address to the nearest 4K boundary automatically. As a result of
this, the erase area will start from a different address (if the
API caller specifies an non-4K alighed address), even though the
size of the erased area is the same as what is specified by the
API caller. Let's add a boundary check to make sure the starting
address (from the API caller) is 4K aligned.
Correct an error in the highest address check. Because of the
error, the erase api call will fail if the flash's highest
address byte is involved.
Jira: ZEP-1277 ZEP-1278
Change-Id: I8b6be57cc8f636f94e5fe67d5a492841a8555005
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This KSDK flash shim driver supports the device in the FRDM K64F
platform (enabled with this commit).
WARNING: the driver disables the system interrupts for potentially
long periods of time. This is required to avoid Read-While-Write
issues since most platforms run in XIP mode.
For more detailed information see the link below:
http://cache.freescale.com/files/32bit/doc/app_note/AN4695.pdf
Change-Id: I70f8d09080251033ce2f45be0c2eb95c19fded08
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Add the necessary infrstructure to support power management for the
QMSI Flash driver. If deep sleep is supported, this driver supports
saving its context to be restored on resume.
Jira: ZEP-1006
Change-Id: Ied88e86d13ef9e4e62bd6ac9d8454d9a9a3d2962
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The W25QXXDV_PAGE_SIZE is not a valid erase size supported by
the flash component (section 7.2.23 - 7.2.26 of datasheet
https://www.winbond.com/resource-files/w25q16dv_revi_nov1714_web.pdf)
and it is not used by any code so remove it.
Jira: ZEP-615
Change-Id: I4315fa082d5cbceda65ae8567e0a77e2d4066ef1
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Calls to flash write or erase operations can get preempted
in the middle of the API call if a concurrent call (from
other fiber or task) to the same API is made. The patch ensures
concurrent API calls from other fiber/task is put on hold until
the current operation is completed.
The mechanism is by default not activated. To enable
it, the following flag needs to be defined:
CONFIG_SOC_FLASH_QMSI_API_REENTRANCY
Jira: ZEP-414
Change-Id: I39429e40cb6ed446123dd1a1d7c7acc1b12417aa
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixed doxygen comments for flash API usage. Clarified the use of
flash_write_protection_set API for write and erase operations.
Jira: ZEP-383
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Change-Id: I6a323915c63a393b7be8f96fe3fcd9616a9b21d1
Quark flash sub-driver. It is based on the QMSI driver.
In order to enable this driver, the following options
must be set.
CONFIG_QMSI_DRIVERS
CONFIG_QMSI_INSTALL_PATH
CONFIG_FLASH
CONFIG_SOC_FLASH_QMSI
Origin: Original
Change-Id: Iffbea3b17624c755e367677b76d7216c2fba2ca1
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
If the driver fails initializations, do not set the driver_api.
This follows the idea that device_get_binding() will not return
a reference to the driver instance when driver init fails.
Change-Id: Iff56b4150658a76567928b1fd166bde5d2848d52
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This patch replaces all occurences of the macro DEV_NO_SUPPORT by
-ENODEV at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I03007527367b03e6fd72a85004b7d3b81046a6a6
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_INVALID_OP by
-ENOTSUP at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I46aec3c65963018c479b01602e4a3eec8650eaff
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_FAIL by -EIO
at the driver level. So this patch touch the files under drivers/,
include/ and samples/drivers/ when applicable.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I0594ab5dbe667e074c250129e7c13ce512ac940f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This patch replaces all occurences of the macro DEV_OK by the actual
value 0 at the driver level. So this patch touch the files under
drivers/, include/ and samples/drivers/.
This patch is part of the effort to transition from DEV_* codes to
errno.h codes.
Change-Id: I69980ecb9755f2fb026de5668ae9c21a4ae62d1e
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Now that the internal libc has the off_t type it's the natural choice
for the offset parameters in the flash API.
Change-Id: I69999999625b46634f6d3008fe1b3f82c17d357c
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This makes the ordering consistent e.g. with SPI, Bluetooth and
Networking APIs. This also follows the order of parameters in the
POSIX read/write APIs.
Change-Id: I4f11c8c90ccadf176d79f6a7bbd98aac61c26cf5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
size_t is the natural type for any integer that describes a number of
bytes. For the actual data use void pointers to avoid callers having
to do explicit typecasts if the data doesn't originate in a uint8_t
array. Also use a const pointer for writing to avoid typecasts for
data that originates in a const location.
Change-Id: Idbfc14b2d61ca6189411b211c3727f857dbd4059
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
SPI flash sub-driver to support WinBond SPI flash.
It is based on the generic flash driver framework.
Change-Id: I58202e38445a052fa0556b03f854e75ef836e2dd
Signed-off-by: Baohong Liu <baohong.liu@intel.com>