Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix setting of the I2C bus master device name for the GPIO_PCAL9535A
device and PWM_PCA9685. We need to extract them from the dts otherwise
they will just get set to "".
Fixes#13458
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We've removed the QMSI RTC driver as part of the new counter API. So
any old rtc tests don't build for QMSI based boards anymore. Switch
this from 'rtc' to 'counter' in the board.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To avoid confusion, callbacks using ordinal pin numbers
is going to be reverted. So the driver has to be re-worked
to expose multiple devices so each device has 32 pins.
Also fixes#12765
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
PAE tables introduce the NX bit which is very desirable
from a security perspetive, back in 1995.
PAE tables are larger, but we are not targeting x86 memory
protection for RAM constrained devices.
Remove the old style 32-bit tables to make the x86 port
easier to maintain.
Renamed some verbosely named data structures, and fixed
incorrect number of entries for the page directory
pointer table.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Convert the w25qxxdv driver to use device tree for SPI device params.
Updated the Arduino 101 config to use device tree to specify the SPI
flash. Update the arduino_101_sss to drop Kconfig support for the
w25qxxdv flash.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
"-machine type=pc-0.14" appears to be the option which leads to
broken PCI emulation in QEMU, where PCI enumeration reports one
IRQ number (11), while actually IRQ 10 is emulated by QEMU.
"-vga none" and "-display none" appear to be just subordinate of
"-machine type=pc-0.14" and are required to get qemu_x86 into
bootable state.
Fixes: #11706
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add documentation for the quark_se_c1000_devboard with links to platform
guidelines and other details.
Fixes#11166
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Merge up_squared_dts_fixup.h and up_squared_sbl_dts_fixup.h into
dts_fixup.h. This allows us to remove BOARD_DIR from being included
everywhere.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix link text to remove substitutions that are ignored by Sphinx. Also
replace link to Quark SOC HW ref manual to be from an Intel site (not
Russian).
Fixes: #11516
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Added support to the ti,cc2520 binding for optional GPIO signals and
moved the quark_se_c1000_devboard to define those signals in the DTS.
This lets us remove board.h and some #defines & fake Kconfig symbols
from the quark_se_c1000_devboard board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CC2520 device is specific to the quark_se_c1000_devboard not the
intel curie SoC. Move the device node where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the in tree user of cc2520 uses device tree to configure SPI
and GPIO params, we can remove and convert the driver to utilize DT
only. This means removing the Kconfig options that come from DT and
rename CONFIG_ to DT_ for those options.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of cases of CONFIG_I2C_x_IRQ_PRI should be
DT_I2C_x_IRQ_PRI. So go ahead and fix them up. Only the i2c_nios
driver still uses Kconfig for getting priority.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a primitive board configuration for the UP Squared board to
work properly with SBL(Slim Bootloader).
- https://github.com/slimbootloader/slimbootloader
- https://slimbootloader.github.io/
BOARD shall be 'up_squared_sbl'
cmake -GNinja -DBOARD=up_squared_sbl ..
ninja
Signed-off-by: Aiden Park <aiden.park@intel.com>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Previously we had a set of magic #define's in board.h that would both
enable and set the GPIO controller & pin if a given board used a GPIO
for USB VBUS. Now we make it a proper Kconfig set of options that
specify if the feature is needed, the GPIO controller device name, and
pin number. In the future this should move to devicetree.
Updated the related boards that used this feature to set the Kconfig
options in the Kconfig.defconfig
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce new Kconfig option for selecting either slip or ethernet
connectivity to host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This required wiring external daughter board by hand, it's not provided
by the board directly, let's remove this.
Applying the change on relevant samples.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove either duplicate settings between arch & board, or just set
HAS_DTS at the arch level since all the boards for a given arch support
DTS now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Options "-clock dynticks" and "-balloon none" are deprecated and
produce warning in recent Qemu versions, so remove them.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove some references <board.h> that aren't need or replace them with
<soc.h> where that is the proper include to pull in. Also use "board.h"
instead of <board.h> for how we include the file when its local to the
board code itself.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following dts warnings:
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/gpio@0:
simple-bus unit address format error, expected "d0c50000"
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/i2c@91528000:
simple-bus unit address format error, expected "9158000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This feature was a useless noop based on mistaken API understanding.
The idea seems to have been that k_busy_wait() included guards to
ensure "clock_always_on" was true duing the loop, presumably because
the original author was afraid that "turning the clock off" would
affect the operation of k_cycle_get_32().
Then later someone came around and "optimized" this for Quark SE,
where the cycle counter is the RTC and unrelated to the timer driver
used by the clock_always_on feature. (Except even there it presumably
should have been done at the SoC level and not just in the C1000
devboard -- note that Arduino 101 never would have gotten this).
But it was all a mistake: "clock_always_on" has nothing to do with
en/disabling the system cycle timer (which never happens when the
system is active, that's a feature of idle), it's a control over the
delivery of timer interrupts. And needless to say we don't care about
timer interrupts when we're spinning on a cycle counter.
Yank the whole mess.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This will be usefull to tell when Ethernet device has its attributes
filled in by DTS rather than by Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert over x86 based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Makes the designware spi driver consistent with other spi drivers by
selecting HAS_DTS_SPI in the driver. This required adding spi nodes and
dts fixups to several arc and x86 socs, as well as enabling those nodes
in associated boards.
Also refactors the driver to use the base address, interrupt number, and
interrupt priority from dts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The i2c drivers now consistently select HAS_DTS_I2C, so we no longer
need to select it at the board level.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sets the HPET timer frequency (enabled by default) to 19.2MHz.
And also sets the local APIC timer frequencies according to
the SoC variant.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are currently three SoC variants for the UP Squared board:
Pentium, Celeron and Atom. This adds a board option to specify
for which variant is being built.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit b0d3b560238fac09e63064620de9ff820cf8cc47.
Since we now have a working ADC driver for Quark D2000,
re-add the tag.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The stub is used for testing only and is not compatible anymore with the
usage documented here.
Fixed#9772
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
set DISK_FLASH_MAX_RW_SIZE to 256, as maximum bytes that can be
programed to SPI FLASH by Page Program Command is 256.
Fixes#8506
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The board config has been verified to boot with serial console
on the Atom version of the UP Squared board. So the references
to Pentium/Celeron can be removed. Moreover, add some notes on
BIOS settings, as it may change the MMIO addresses for various
IP blocks.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add the necessary bits to enable the I2C controllers on
the UP Squared board. Only the ones exposed through the HAT
connector(s) are enabled by default.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a primitive board configuration for the UP Squared board
containing Apollo Lake based Pentinum and Celeron SoC. This has
been tested on model UPS-APLP4-A10-0432.
This starts from the minnowboard configuration, and document
from galileo.
Origin: Original
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This extends the build_grub.sh script so that it can build 64-bit
Grub UEFI application, and thus enabling us to boot on systems
with 64-bit BIOS.
Also updated the script to checkout the tag grub-2.02 since
v2.02 has been out.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The PHYS_LOAD_ADDR Kconfig symbol was removed by commit b8ea7c889d
("x86: remove HAS_DTS checking"). The ROM_SIZE Kconfig symbol was
removed by commit e524f0b846 ("dts: x86: derive RAM and ROM size from
dts instead of Kconfig").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add first set of boards which can be built with xtools, this will
include all boards at some point, so we might need a better way to
whitelist toolchains that does not include changing every single board
definition file. For now enabling those needed for testing the new
toolchain.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Make these "choice" items instead of a single boolean that implies the
element unset.
Also renames WAITQ_FAST to WAITQ_SCALABLE, as the rbtree is really
only "fast" for large queue sizes (it's constant factor overhead is
bigger than a list's!)
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that for any of the removed properties though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
CONFIG_SPI_FLASH_W25QXXDV_MAX_DATA_LEN is a left-over from old SPI API
usage. Now, there is no limit (besides the flash size) in SPI data
transaction.
Fixes#8327
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These symbols were removed by commit ed26b95 ("drivers/gpio:
Removing dts generated options in QMSI Kconfig"). The settings should
come from DTS now.
Commit 9611002f7a ("boards/x86: Use right GPIO names for CC2520")
fixed some of the references, but there are still others left. Guess
that the same fix is appropriate in those spots (hardcoded
"GPIO_0"/"GPIO_1" names).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
GPIO_QMSI_<0/1>_NAME are now generated through DTS. Until CC2520
settings are generated through DTS, let's use direct gpio names
instead.
Fixes#8086
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
According to INTEL-SA-00115[1], Intel(r) Atom(tm) Processor E Series
are affected. All Minnowboards sports one of these processors.
[1]: https://goo.gl/CKyLQy
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The Kconfig option TOOLCHAIN_VARIANT (not to be confused with
ZEPHYR_TOOLCHAIN_VARIANT) is a legacy configuration option that has
very few use-cases and can easily be dropped.
It's functionality is easily covered by CONFIG_X86_IAMCU and
ZEPHYR_TOOLCHAIN_VARIANT.
This commit removes all references of it from Zephyr.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The current method of setting the openocd runner arguments works for
direct invocation from the command line, but the values that are
written to the CMake cache are not properly separated and are
difficult to parse, due to the fact that in several cases, option
values contain spaces.
Adjust these runner arguments so that the options and their values are
separate list items. This makes it possible to parse them accurately
from the CMake cache.
No functional changes.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
This target is already using the rbtree as part of CONFIG_USERSPACE,
so it incurs no code size overhead (actually it's a little smaller)
when using the scalable scheduler and waitq implementations.
The change also gets us test coverage of those choices on a default CI
target.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
patch removes Kconfig defines for RAM and ROM size in x86. Instead
these values are derived from dts.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
boards/x86/arduino_101/arduino_101_defconfig currently enables
CONFIG_UART_QMSI_0_HW_FC (HW flow control on UART 0), but doesn't enable
CONFIG_UART_QMSI_0 (the UART itself), which is a direct dependency.
This means CONFIG_UART_QMSI_0_HW_FC remains disabled despite the request
to enable it, and kconfig.py prints a warning.
Enable CONFIG_UART_QMSI_0 in the arduino_101_defconfig.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We are testing and building this already using qemu_x86, no need to
build the same thing all over again.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
QMSI is not updated to latest SPI API. Switching to native DW driver,
until we find a way either to update the shim drivers in a
non-performant way, or updating QMSI itself enabling support for
scatter-gather type of buffers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Currently, it seems that only boards with smaller amount of RAM
get a value for "ram" property, and very few boards have "flash"
defined. However, to test bigger sample applications, it's helpful
to have these properties universally defined.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
According to a conversation with @carlescufi and @finikorg, the
zephyr codebase should only use the Linux Foundation USB vendor
ID. The USB vendor IDs and product IDs in the board definitions
are an obsolete leftover from old code and no longer needed.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
We assumed that ${BOARD} and ${BOARD_FAMILY} are always the same and
thus interchangeable. That isn't always the case so use ${BOARD} proper
for when we mean the exact BOARD name we are building for vs the
BOARD_FAMILY.
We also add .dts files for board variants within a board family, such
that we have a .dts matching each board name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/atom/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/ia32/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/x86/soc/intel_quark/quark_se/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
MinnowBoard has an uppercase "B" in its name. Also added a link to the
config option mentioned.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add a reference to flashing and booting so it can be used by minnowboard
and other boards.
Apply minor layout fixes.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some boards are supported natively by qemu. This option will allow us to
run tests using those platforms directly without having to go via a
dedicated qemu board definition.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In order to be able to document the build on Windows and UNIX
systems, slight variations are required on the app commands
that are used throughout the documentation system.
This includes getting rid of the prompt symbol and providing commands
for both UNIX and Windows operating systems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Most boards enable the pinmux by default by setting CONFIG_PINMUX=y in
<board>_defconfig, but several boards did it in Kconfig.defconfig
instead. Several code reviews, such as #5043, have suggested using a
select in Kconfig.board to enable the pinmux, however this caused
warnings:
warning: (BOARD_LPCXPRESSO54114) selects PINMUX which has unmet direct
dependencies (BOARD_FRDM_K64F || BOARD_FRDM_KL25Z || BOARD_FRDM_KW41Z ||
BOARD_HEXIWEAR_K64 || BOARD_USB_KW24D512 || BOARD_GALILEO)
Fix how these boards enable the pinmux so they are more consistent with
other boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
quark_se_c1000_devboard already embeds a cc2520 which is a 2.4Ghz 15.4
radio chip. But if one want to try a sub-Ghz radio chip such as the
cc1200 on it, it will require to wire as this configuration expects it
to be done.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update board definitions with supported feature. This is temporary
until we have full coverage for device drivers in DTS, then we can use
DTS instead.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The build documentation for this board is misleading. It says to "set
JAILHOUSE_QEMU_IMG_FILE", *then* run cmake commands. But setting the
variable must be part of the cmake commands themselves. Fix it.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The various runners (flash/debug scripts) use environment variables to
take arguments. This is legacy behavior which is not desirable.
Use command line arguments instead.
Note: this leaves more general environment variables with publicly
documented behavior in place for now, for compatibility, e.g.:
ZEPHYR_FLASH_OVER_DFU, OPENSDA_FW, ESP_IDF_PATH, PYOCD_DAPARG
For example, when using dfu-util to flash arduino_101, instead of
setting DFUUTIL_PID, DFUUTIL_ALT, and DFUUTIL_IMG environment
variables, have the script invocation look like this:
python3 .../zephyr_flash_debug.py dfu-util flash \
[common arguments omitted] \
--pid=8087:0aba --alt=x86_app \
--img=.../build/zephyr/zephyr.bin
Make similar changes for other runners (openocd, etc.) and
targets (debug, debugserver).
To implement this in the scripts:
- have the individual scripts/support/runner/some-runner.py files
register their own command line arguments
- teach them to construct instances from arguments, not the
environment
- have zephyr_flash_debug.py request runners to register command
line argument parsers, and handle arguments
In the build system:
- add a new board_runner_args() extension function that board.cmake
files can use to add to the zephyr_flash_debug.py command line
- adjust cmake/flash/CMakeLists.txt to invoke with arguments
- add new helper include files for each runner (like
boards/common/dfu-util.board.cmake, etc.), which add default
options as needed and then add on overrides from
board_runner_args() calls
- update board.cmake files to use the new includes and extension
This implied some tweaking when using openocd to make the CMake string
escaping and unescaping work properly.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The Python-based runners have replaced the old shell scripts. Refactor
the build system accordingly:
- FLASH_SCRIPT is now BOARD_FLASH_RUNNER
- DEBUG_SCRIPT is now BOARD_DEBUG_RUNNER
The values, rather than being the names of files, are now the names of
runners in scripts/support/runner. They are still short, descriptive
names like "openocd", "jlink", "em-starterkit", etc.
Adjust the zephyr_flash_debug.py call and runner internals
accordingly. Have each runner class report a name and the commands it
can handle. This lets us move some boilerplate from each do_run()
method into the common run() routine, and enables further improvements
in future patches.
The handles_command() method is temporary, and will be replaced by a
more general mechanism for describing runner capabilities in a
subsequent patch. The initial use case for extending this is to add
device tree awareness to the runners.
To try to avoid user confusion, abort the configuration if an
xxx_SCRIPT is defined.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
During cmake migration the load image was not correctly set.
This was causing flash failures.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
For a lot of scenarios the isr stack was no longer enough.
Hence increased the stack size.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This is needed by platforms like jailhouse.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
We don't want to pollute core-infrastructure with board-specific code,
so we move the qemu discovery to after board.cmake has been executed,
and we introduce the overridable QEMU_binary_suffix CMake variable.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
"-serial mon:stdio" was already injected elsewhere, so remove
duplication. That argument, when coming from the common infrastructure,
also comes as one of the last ones. Because of that, the former "-serial
vc" was taking precedence and we were never seeing output on stdio.
Removing the virtual console altogether, for now, fixes that.
Finally, since cmake came in, we have to fix the path for the fsdev
argument to QEMU as well.
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
Getting warnings from Kconfig after generalising how CPU_HAS_FPU is
configured on the architecture level. 2 Boards were settings this value
in the wrong place.
Fixes#5211.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The jailhouse board's build is currently broken.
It wants to depend on the qemu board's devicetree, but can no longer
do so since the board-level dts files were moved into individual board
directories.
To restore the build, insert the qemu_x86.dts contents into
x86_jailhouse.dts.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
patch removes the mem.h and marcos used in that file are
moved appropriate board files. As there are boards with
different flash configuration but of same soc, flash and
ram size are moved to dts file instead of dtsi
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The old way of constructing FLASH_SCRIPT_ENV_VARS was corrupting the
values that were passed to the flasher. This new method is the
standard way of creating a dictionary/hashmap in CMake and does not
suffer from the same problem.
This fixes
https://github.com/zephyrproject-rtos/zephyr/issues/4844#event-1334599401
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
The port will enable Zephyr to run as a guest OS on x86-64 systems. It
comes with a test on QEMU to validate that, thus this new board
introduction. It's "make run" target will issue QEMU with the same
configuration Jailhouse upstream uses for their confis/qemu-x86.c root
cell configuration:
Test configuration for QEMU Q35 VM, 1 GB RAM, 4 cores,
6 MB hypervisor, 60 MB inmates (-4K shared mem device)
This will work provided qemu-system-x86_64 is installed in the system
and a given (qcow2) image with the Jailhouse root cell in it is
provided (any of those will ever ship with Zephyr, it's out of its
scope).
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
Replacing the default paging scheme from 32-bit paging to
PAE paging in QEMU.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Replacing the default paging scheme from 32-bit paging to
PAE paging in QEMU.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Page Address Extension(PAE) page tables make use of NXE bit in
EFER register.
This patch enables the capability needed to set this bit.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The IAMCU variant does not need to be the default, this calling
convention was to support the discontinued Quark platforms.
qemu_x86 and qemu_x86_nommu now are set as default.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will run all tests with the memory management unit disabled.
This means no hardware-based stack protection or user threads.
qemu_x86_iamcu now runs with all MMU features enabled.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Set Vendor and Product ID originally present in the firmware.
Implemented USB function is the same: CDC ACM serial port.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Move all QEMU related defines to the boards and cleanup xtensa platforms
which were marked to be QEMU capable by mistake.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
patch add device tree support for develoement board of
quark_se_c1000. Previously pushed patch was flashing binary
at wrong address because of which UART was not working
Jira:ZEP-2459
test
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Some boards had HAS_DTS in the defconfig which is dropped if the Kconfig
variable does not have a prompt.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This will allow checking if we are building for QEMU globally, without
having to know the exact architecture and board name.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since HAS_DTS is always defined for arduino_101 the board specific
Kconfig bits associated with !HAS_DTS are never used, so lets remove
them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will cause sanitycheck runs to finish more quickly
instead of sitting there waiting on a timeout. We already
do this with the Xtensa simulator.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
patch uses chosen property zephyr,bt-uart, zephyr,uart-pipe
and zephyr,bt-mon-uart to determine the uart instance to be
used for bluetooth,uart_pipe and bluetooth_monitor and generate
appropriate configs.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
We have lots of RAM, this helps catch bugs.
Enable XIP as well, this used to be turned on but was
shut off for some reason.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Previously we were instantiating QEMU with 32MB of RAM but
only enabling a small fraction of it.
Now we boot with 8MB of ram. We ignore the first 4K so we can
make that an unmapped paged to catch NULL pointer dereferences.
If XIP is enabled, the "ROM" region will be the first half of
memory, the "RAM" region the latter.
Move the IDT_LIST and MMU_LIST regions elsewhere so they don't
overlap the new memory arrangement.
Use !XIP to fix a problem where CONFIG_RAM_SIZE was set incorrectly
for XIP case.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This should be a default option for this board which would allow us to
remove it from many sample configurations that can be then used for
other boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Sidebar navigation for supported boards is wonky: opens to show
all boards (making for lots of scrolling to see the sidebar) and
sidebar items aren't always clickable (as explained in the JIRA
issue).
Fix is to not use multiple toctree directives in boards.rst and
create intermediate architecture-specific supported board docs.
JIRA: INF-132
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
patch adds necessary files and does the modification
to the existing files to add device support for
arduino_101 board.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
