With addition of flash_parameters structure, and supporting API call
to retrieve it, it is no longer needed to store write_block_size as
a part of flash_driver_api and it should be part of flash_parameters.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
With addition of flash_get_parameters API call, it is needed to provide
support for the API to flash drivers.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The sam0 has a page size of 64 bytes, making it incompatible with
the nvs driver that specifies a maximum write block size of
32 bytes. When CONFIG_SOC_FLASH_SAM0_EMULATE_BYTE_PAGES is set,
it should report a write block size of 1 byte, which is compatible
with nvs.
Signed-off-by: Adam Serbinski <aserbinski@gmail.com>
Use the UNALIGNED_GET() macro instead of the
flash_sam0_read_unaigned_u32() function to ensure
word alignment of the source address.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
drivers: flash: sam0: fix whitespace
Fix checkpass whitespace error.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The amount of lock regions differs between different sam0 MCUs.
saml10: 2
saml11: 4
samd2x: 16
saml2x: 16
samd5x: 32
ASF does not provide a definition for this, so create a new one
in dts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This adds support for the flash peripheral found in the SAME5x/SAMD5x
line of MCUs.
The peripheral is very simmilar to the one found on SAMD2x with only
a few register names changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This commit fixes following issues in printf formatting used by flash
drivers:
- cast values of type off_t to long to remove warnings generated when
compiling with Newlib.
- use 'z' modifier (as in "%zu") to print values of type size_t
- prefix all hex numbers with '0x'
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The sam0 flash driver has support for retrieving flash page layout
information. This commit fixes compilation when
CONFIG_FLASH_PAGE_LAYOUT is disabled.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SAM0 has a 64 byte page (the programing unit) with 4 pages to a
row (the erase unit). This driver implements a read/modify/write to
emulate the byte level writes used by NFFS.
Signed-off-by: Michael Hope <mlhx@google.com>