Fixes the adt7420 sensor sample to fail gracefully if the sensor device
is not found and asserts are not enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit provides sample application for sensor lsm6dsl.
This sample has been tested on both 96b_argonkey board,
where lsm6dsl is connect to the micro thru SPI bus, and on
disco_l475_iot1 board, where instead it is connected to I2C bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a configuration structure to sht3xd that holds instance-specific
parameters, implemented in a immutable statically allocated object
initialized with material from device tree binding aliases.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Add Accelerometer mouse by using fxos8700 accelerometer and using data
to control USB HID mouse.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
The options selecting given hardware instances are now enabled at
the board level.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Regex pattern matching is included to match the
execution log from console to return test result
in automation.
Also add fixture to identify the external sensor
connected for automation framework to trigger test
cases on particular board which is connected with
required sensor.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Driver fxos8700 can also be used for the MMA8451
accelerometer and offers more functionality.
Revert the commit to avoid duplicate code.
This reverts commit 70a35e2346.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Remove redundant 'sample' tag and add something that matches the
functionality and features being tested, demonstrated.
Avoid short abbriviations and using full names for fs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add sample application for LSM303DLHC, ST MEMS
system-in-package featuring a 3D digital linear
acceleration sensor and a 3D digital magnetic
sensor.
Enable sample to build on stm32f3_disco board
during sanitycheck.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The spi project configuration was incorrectly enabling i2c, which causes
a cmake failure if a board supports spi but not i2c. Found by CI when
adding spi support to the mimxrt1050_evk board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This sample application produces slightly different outputs based on
the chosen driver configuration mode. In Measuring Mode with trigger
support, the acceleration on all three axis is printed in m/s^2 at
the sampling rate (ODR). In polled Measuring Mode the instantaneous
acceleration is polled every 2 seconds. In most high-g applications,
a single (3-axis) acceleration sample at the peak of an impact event
contains sufficient information about the event, and the full
acceleration history is not required.
In this Max Peak Detect Mode the device returns only the over
threshold peak acceleration between two consecutive sample fetches or
trigger events. Instead of printing the acceleration on all three axis,
the sample application calculates the vector magnitude
(root sum squared) and displays the result in g rather than in m/s^2,
together with an bar graph.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Update yaml files to include warp7_m4 board in the platform_whitelist
for fxos8700 and fxas21002 sensors.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Prepend the text 'cmake_minimum_required(VERSION 3.8.2)' into the
application and test build scripts.
Modern versions of CMake will spam users with a deprecation warning
when the toplevel CMakeLists.txt does not specify a CMake
version. This is documented in bug #8355.
To resolve this we include a cmake_minimum_required() line into the
toplevel build scripts. Additionally, cmake_minimum_required is
invoked from within boilerplate.cmake. The highest version will be
enforced.
This patch allows us to afterwards change CMake policy CMP000 from OLD
to NEW which in turn finally rids us of the verbose warning.
The extra boilerplate is considered more acceptable than the verbosity
of the CMP0000 policy.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This simple application periodically prints the ambient temperature.
Optional support for threshold triggers is provided.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
No need to have a category for grove, instead moved the samples to both
sensors and display based on what the sample does.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This symbol never existed, and has some dead code associated with it:
https://github.com/zephyrproject-rtos/zephyr/issues/7848
Just remove the assignment to the undefined Kconfig symbol for now. The
associated code could be removed separately if it isn't needed anymore.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use zephyr-app-commands for portability instead of assuming Make on
Unix, also adding a missing "flash" invocation.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Some device include a temperature sensor, usually used as a
companion for helping in drift compensation, that measure the
die temperature. This temperature IS NOT related to the the
ambient temperature, hence a clean separation between the two
is required.
This commit introduces a clean separation between the two
types of temperature leaving the old deprecated definition
still there.
The list of current drivers that read the die (and not the ambient)
temperature is the following:
- adxl362
- bma280
- bmg160
- bmi160
- fxos8700
- lis3mdl
- lsm6ds0
- lsm6dsl
- lsm9ds0
- mpu6050
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Not all boards are going to have the ccs811 on them, and thus not in the
device tree. We need a dts.fixup stub to dummy out the CONFIG_CCS811_*
defines that the driver expects.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add sample application for AMS CCS811 digital gas sensor driver.
This application fetches Co2, VOC, Voltage and Current readings
from the sensor and prints it on serial console continuously.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
SENSOR_CHAN_DISTANCE is now in meters. Print value in meters, as
double, this requires printf() and CONFIG_STDOUT_CONSOLE. This is
similar to how other sensor samples have it.
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Based on the discussion in #5693, the reason why humidity was defined
in milli-percent was likely following Linux which defines it as such
in its sensor subsystem:
http://elixir.free-electrons.com/linux/latest/source/Documentation/ABI/testing/sysfs-bus-iio#L263
However, Linux defines temperature in milli-degrees either, but
Zephyr uses degrees (similarly for most other quantities). Typical
sensor resolution/precision for humidity is also on the order of 1%.
One of the existing drivers, th02.c, already returned values in
percents, and few apps showed it without conversion and/or units,
leading to confusing output to user like "54500".
So, switching units to percents, and update all the drivers and
sample apps.
For few drivers, there was also optimized conversion arithmetics
to avoid u64_t operations. (There're probably more places to
optimize it, and temperature conversion could use such optimization
too, but that's left for another patch.)
Fixes: #5693
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The hts221 sensor driver was implicitly made dependent upon the
disco_l475_iot1 board when it was converted to dts, so build the
associated sample only for this board. This issue was encountered when
adding sensor dts support to nxp boards, which don't have hts221.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This sample application allows to test vl53l0x distance sensor.
By default it is built with disco_l475_iot1 board as it is
built-in.
Signed-off-by: Vincent Veron <vincent.veron@st.com>
Since no GPIO trigger is configured in hts221 sample application,
update prj.conf to enable TIGGER_NONE flag
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove build_only and add harness type needed for the sample/test to
allow running with sanitycheck and on devices once we have harness
support.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
To test BMM150 geomagnetic sensor driver in polling mode,
sample application added by this patch can be used.
Signed-off-by: Punit Vara <punit.vara@intel.com>
Sample can be used to test ambient light, RGB and proximity
functionality of APDS9960 sensor in polling mode.
Remove old sample which is not using sensor API.
ZEP-1552
Signed-off-by: Punit Vara <punit.vara@intel.com>
We have many testcases doing filtering both on the architecture level
and the platform level, which is redundant. Also many testcases are
running the same test twice on the same SoC for no good reason, cleanup
the tests and cleanup the filtering.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This will prepare test cases and samples with metadata and information
that will be consumed by the sanitycheck script which will be changed to
parse YAML files instead of ini.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some files have moved from their original location, or are no longer
available. For the mbedtls samples, tweak the link to point to a page
where links for current and previous downloads can be found.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This commit provides sample application for sensor hts221.
By default, it is enabled on board disco_l475_iot1
Change-Id: I535fac8a670fa89cc1cae15ea1abe9cfe4b6c56b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08c682bfc0b80dfa88de859e90a011bcd2db2762
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a max30101 sample application that polls sensor data and prints it
to the console.
Jira: ZEP-720
Change-Id: I50f28eaf9ea2ff5bfbb9fb6922c4006d5c02e739
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Docs need a label at the top so we can use :ref:`labelname`
to create a link to that doc from other docs.
Change-Id: I37c654fb0bb7ebdf288af01e41ce5497969f8968
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Updates the fxos8700 sample documentation to include board
cross-references and sample output with temperature data.
Change-Id: I8d4e4d8d287806f5480316da09d4072fcf9c05ac
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a fxas21002 sample application that uses the sensor data ready
trigger to periodically print gyroscope data.
Jira: ZEP-1392
Change-Id: Ic9d3803a41f2873aef470a2a73b3f1db44d39b50
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the temperature sensor in the fxos8700 sample.
Change-Id: I2b4c306d3c5528dc32d940476c00180b5df08187
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The fxos8700 driver was previously converted to use the generic
SYS_LOG_SENSOR_LEVEL. Update the fxos8700 sample to use it too.
Change-Id: I2ef02342ce3a25e8d3a3d1b13181872ca0abdc16
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Support connection via SPI and keep I2C as the default.
Jira: ZEP-1698
Change-Id: I42a76131577a37429375364deb07e451107f5d81
Signed-off-by: Dario Pennisi <dario@iptronix.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Binding of the device failed due to incorrect device name. Update
to use the correct device name.
Jira: ZEP-1704
Change-Id: I6ca23a439357592c9c974ca746bccc35e77d996d
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Use new device name for SPI device
Jira: ZEP-1704
Change-Id: Iec39468bbef54423af2b3a681dd4ae1eee866d1e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Reduce the accelerometer sampling frequency for polling mode.
So, cpu has more time to fetch the sample.
Also add some waiting time for the new frequency setting to
take effect.
Jira: ZEP-1532
Change-Id: If5c1d8a2b5f30b232a212f2775306ca397b9f80c
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
SENSOR_CHAN_*_ANY will be deprecated, so use the new SENSOR_CHAN_*_XYZ
enum values.
Change-Id: I91cf25864613a934feab65588969d10c52fd4fe6
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
At the default sample rate of 400 Hz, there is not enough bandwidth on
the UART at 115200 baud to print every sample. Fix by decimating the
sensor data by 4 before printing to the console.
This issue was discovered after fixing ZEP-1507.
Change-Id: I451ec9873ca93fe417d5d5a2d6d13b5e921c7611
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The headings on some .rst files were not following the expected
heading order of using # for h1, * for h2, = for h3, and - for h4
This patch fixes that, and the doc/templates/*.tmpl files created
for folks to use as templates for creating board and sample docs.
Change-Id: I0263b005648558d5ea41a681ceaa4798c9594dd9
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Printing values as <integer_part>.<fractional_part> gives undesired
results for negative numbers, so print the values converted to floating
point to avoid this.
Change-Id: I871b8461f2d643a2adce67df064e9f5e6d506319
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the convert_to_double function and use sensor_value_to_double
from sensor.h.
Change-Id: I92ef4219057f431917f4c8e9d46d4ee2074b423b
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Remove the type field from the sensor value structure. All values will
have the type previously defined by SENSOR_VALUE_TYPE_INT_PLUS_MICRO.
This simplifies the interface, as apps will know what value type to
expect. Apps that prefer to use double values can optain them using the
sensor_value_to_double function.
Change-Id: I3588d74258030eb16c3f89d8eead13cca4606b18
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Various sensor samples are hardwired to expect returned sensor values
are represented as doubles. In each case this assumption is incorrect.
Introduce a generic sensor_value to double helper function and adjust
the samples to use it.
Change-Id: I89c788686576562b84e07a36064640231340c33b
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This will allow inclusion of documentation files that exist outside of
doc/ and will make it possible to add rst files across the tree,
especially for boards, samples and tests.
Change-Id: I7afcf92d99f504b2bc0b2b7e3452acb2f8e08294
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The dev name for spi in the sensor sub-system was changed to
SPI_SS_x from SPI_x recently. Let's use the new name in the
sample app.
Change-Id: I78cdf21fce16290503c303e0de1432b4587486aa
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Remove CONFIG_BMI160_TRIGGER_SOURCE_GPIO from prj config
file. It is not being used any more.
Also change CONFIG_STDOUT_CONSOLE to CONFIG_PRINTK. The
whole sample is using printk instead of printf.
Change-Id: I4ac7db37da1e45aed2457ace9e82385e37143c36
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Directly use AON GPIO trigger instead of IPM.
In the past, SW did not allow arc to receive AON GPIO interrupt.
So, interrupt from BMI160 was routed to x86 cpu. Then, x86 cpu
passed the event to arc through IPM. But, SW was updated and arc
is able to directly receive interrupt from AON GPIO now. So, IPM
is not needed any more. Both IPM and GPIO triggering code is there.
We just need to change the configuration by modifying the prj
config file.
The x86 code will be removed since it will not be used any more.
Change-Id: Ibc4250a34218cc52bf4c726cf70617cfdea3b2e8
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Remove SENSOR_VALUE_TYPE_INT as it is the same as
SENSOR_VALUE_TYPE_INT_PLUS_MICRO with val2 set to 0.
Change-Id: If5a9c579b7267701c27f40fd887acae47d64edc5
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Remove SENSOR_VALUE_TYPE_Q16_16 as it is not used by any driver. Future
drivers can use any of the remaining value types.
Change-Id: I984143cc65d6a6fd0477f310ac17c62498cc05b8
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
The sample was reading the sample values regardless of return
value of the fetch sample function, now it exits the function and
prints an error message
Coverity-CID: 157576
Change-Id: If9a909ed9b617357a032c5632ac04984846d6744
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Adds a fxos8700 sample application that uses the sensor data ready
trigger to periodically print accelerometer and magnetometer data.
Change-Id: I43fef6cd6090b58d8d0168a25558a3a05781ea5d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove nano kernel references found at the README files.
Change-Id: Id42f4797561f3d7674110bb84531b5f6e487decd
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The sensor_channel_get return code is now evaluated.
Change-Id: Ib931d6caba65af7195bad53c62e6e5a3033b49e8
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
convert all sensor drivers to use threads and the unified kernel API and
remove all legacy APIs.
Change-Id: Ica43ea74ecbbf85273f718f182c413a9dcd8abc6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove those from Makefiles and testcase.ini, we now support unified kernel
only and sanitycheck script now knows how to deal with this.
Change-Id: I853ebcadfa7b56a4de5737d95f2ba096babb2e13
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
- remove useless Kconfigs
- remove SPI DW kconfigs, we now use QMSI driver
- Cleanup readme and turn into ReST
Change-Id: Ie1f39e0afabf499fa81627ded59adf267e01993a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enhance documentation and build for Quark D2000 Devboard by default.
Change-Id: I3417c31a8898a076465d25f45d7821820b480290
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This sample uses the grove temperature and humidity sensor and displays the
read values on the grove LCD.
Change-Id: Id6fb6171c26c97f1b01008fa06a4dc85287d7545
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Using AON for GPIO kconfigs is very specifc to quark se, there
is no need to make this special for this platform. Use the
existing scheme instead.
Change-Id: I946431490380dc0f537d6056277a94c9c9c80fed
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In many cases there is no need to define a macro for printing to
the console, just use the correct variant directly.
Jira: ZEP-240
Change-Id: I9952deda4bfc60424f01fca2443d037562d13d0d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change tags to reflect the type of samples, in this case it is all
about sensors.
Change-Id: I9f87e8683dd52fd757cd07ba5aa9fad99d17ab38
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Treat the sensor subsystem as an independent board that can send
messages to UART and disable IPM and the messaging interface. IPM
can be enabled by applications that require such interface.
Fix all samples that are affected by this change to make sanitycheck
pass.
Jira: ZEP-451
Change-Id: I3df6af16adefaefec02b97778d6c68ffc920ac35
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove generic PRINT macros from sensor samples and replace
with SYS_LOG module.
Jira: ZEP-240
Change-Id: I474efcd1daf8e621acd50d88b3a9662b8cd2b516
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Fix several issues which are causing the BMI160 app hang.
For SPI duplex transfer, QMSI only supports equal length.
For SPI freq, divider is used. Actual freq is no longer used.
Jira: ZEP-461
Change-Id: I1a1bcc12c6514c3797686dfdad1ce1b852f7dc78
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Add helper function for printing sensor_value to char buffer.
Change-Id: I46329675d9a69376ea74c4f7dfcb270ca2078c72
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
The sample prj.conf file was using CONFIG_BMI160_DRV_NAME which doesn't
exist. Use CONFIG_BMI160_NAME instead.
Change-Id: I6eb29bf7772055a7b1fd62461fabe8e358dd10ec
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a sample app to read MAX44009 light sensor via i2c
of quark se sensor system.
Origin: Original
Change-Id: I7078b3383021cdc81ff7b59fd1958e6bf86fe988
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Periodically reads temperature and prints it on console
Change-Id: I293a7aad88bce245d6c1149fd19fcb7c7e770e54
Signed-off-by: Mariusz Ryndzionek <mariusz.ryndzionek@firmwave.com>
$srctree for the application might not be set to be $ZEPHYR_BASE, use
$ZEPHYR_BASE instead to be more explicit in the build.
Change-Id: Iefa5ff59f246b584949329044f7a6531adc6ed62
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the CONFIG_SENSOR_DEBUG as it is no longer needed since switching
to SYS_LOG_* in the sensor susbsystem.
Also, use __ASSERT where CONFIG_SENSOR_DEBUG was used to validate
function parameters.
Change-Id: I80ed7209abfb92220fa229d246c5b3a43b887e32
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
* Rename BMP280 to BME280 which is a superset for the former.
* Autodetect device based on chip ID.
* Implement humidity fetching and reading for BME280
* Rename sample BMP280 to BME280
Change-Id: I565c769a7011e7496c9f1cad861d5ee311839b4f
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Using ARCH variable to select different configurations for the different
architectures is misleading and conflicts with the variable ARCH being used by
the build system. The variable is not needed, it is application specific and
an application can be built without the need to specify ARCH on the command
line.
This is yet another item specific to samples and test cases that
wrongfully being used and documented for every application. We need to use
another variable and just make it clear it is specific to samples and how they
are written. One possible solution is to have a script that gets the
architecture based on the board being used. Attachments
Jira: ZEP-238
Change-Id: Ieccbc087a41858fb96fb361c0aaa04705e968a4e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the same Kconfig infrastructure and options for all SPI drivers.
Jira: ZEP-294
Change-Id: I7097bf3d2e1040fcec166761a9342bff707de4dd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>