Only boards with at least 64K Flash will activate MPU because:
MPU + UERSPACE + All switches implicity activated
(CONFIG_MPU_STACK_GUARD, CONFIG_ARM_STACK_PROTECTION ...)
will consume about 40K Flash
(value computed on nucleo_f767_zi on tests/arch/arm/arm_ramfunc/).
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The STM32L072CZ MCU has a built-in USB device controller which is
supported by Zephyr's USB STM32 driver. The b_l072z_lrwan1 board has a
micro-USB connector that is wired to the MCU via two solder bridges
(SB15 and SB16) that need to be closed to connect the data lines.
Update the board documentation to describe the solder bridges and
enable the USB controller in the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The documentation page in Zephyr states that the STM32L072CZ has 20KiB
of EEPROM. This is incorrect, the datasheet (and DTS) indicates that
it has 6KiB of EEPROM.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
The STM32L072CZ has an EEPROM for user configuration. Enable this for
the B-L072Z-LRWAN1 Discovery kit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_I2C flag to for each i2c pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SPI flag to for each spi pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to avoid pin configuration conflicts between peripherals,
add CONFIG_SERIAL flag to for each serial pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
OpenOCD currently uses a single-bank STM32 configuration for the
B_L072Z_LRWAN1 board. This causes flashing to fail when the firmware
image is larger than the first bank. Switch to the dual bank
configuration to make this work.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The Kconfig I2C_[0-9] sybmols don't have any meaning for the majority of
SoCs. The drivers doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
SPI1, which is used by the LoRa radio, has the following
configuration:
SCK: PB_3
MISO: PA_6
MOSI: PA_7
NSS: PA_15
Update the pinmux configuration and documentation to reflect this.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed by other symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move systick activation in soc/ as a Kconfig.defconfig file and
remove activation in boards _defconfig files.
This will allow to deactivate it in a more flexible way
with upcoming LPTIMER as tick source when power management
features are enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Allow the user to use software slave select instead of the
hardware pin, in order to free the related GPIO and avoid
unwanted SS triggering on the hardware pin. The default SS
is still the hardware pin.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix misspellings and doc issues missed during regular reviews (including
some files without a trailing newline)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
interface/stlink-v2-1.cfg and interface/stlink-v2.cfg are wrappers
around interface/stlink.cfg, their inclusion trigger warning which
this change addresses. Besides the warning there is nothing there
except sourcing iterface/stlink.cfg directly.
Signed-off-by: Vasili Slapik <vslapik@gmail.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added support for ST B-L072Z-LRWAN1 board configuration.
This board uses the same MCU as Dragino-LSN50.
Signed-off-by: Aleksandr Makarov <seems.deviant@gmail.com>
