On the STM32MP2 series, the IPCC clock is managed at the system
level by the CPU responsible for system configuration.
In topologies where the Cortex-M33 acts as a companion processor, it
cannot enable the IPCC clock.
This update makes the IPCC clock optional in both the device tree
and the driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Add migration guide and release notes entries for the radio-related
devicetree binding renames:
- generic-fem-two-ctrl-pins -> radio-fem-two-ctrl-pins
- gpio-radio-coex -> radio-gpio-coex
- tx-high-power-supported -> radio-tx-high-power-supported
Also document the new radio.yaml base binding for generic radio
hardware capabilities.
Signed-off-by: Ivan Pankratov <ivan.pankratov@silabs.com>
Rename GPIO coex binding to use 'radio-' prefix for consistency with
other radio bindings (radio.yaml, radio-fem-two-ctrl-pins.yaml).
Updated beacon sample overlay and coex documentation.
Signed-off-by: Ivan Pankratov <ivan.pankratov@silabs.com>
Rename generic FEM binding to use 'radio-' prefix for consistency with
other radio bindings (radio.yaml, ble-radio.yaml).
Updated 3 board files, Nordic BLE controller HAL, documentation, and
test overlays. Added missing settle-time properties to pan1783a board.
Signed-off-by: Ivan Pankratov <ivan.pankratov@silabs.com>
Create a shared base binding (ble-radio.yaml) for common Bluetooth LE
radio hardware capabilities to avoid duplication between vendors and
ensure consistent property naming across the ecosystem.
Properties are prefixed with 'ble-' and ordered chronologically by
Bluetooth Core Specification version (5.0, 5.1, 6.0). Each property
indicates a hardware capability, not current enablement state.
Signed-off-by: Ivan Pankratov <ivan.pankratov@silabs.com>
Some of the CAP initiator unit tests did not delete the group
after creation, even if they easily could.
Especially for test_initiator_unicast_group_add_streams it was
a problem, as the stream added was stack allocated, and by the
end of the test it was deallocated, causing issues when the
group was finally deleted in
cap_initiator_test_unicast_group_after.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify the unit tests to use the native_sim board instead of the
unit_testing board.
The native_sim board allows us to use the kernel in a more
regular way, while still being able to treat the tests as
unittest.
To support mocking we cannot rely on the default
Kconfig options and values. The required Kconfig options
to satisfy dependencies are overridden in the Kconfig
file and the necessary Kconfig files are sourced.
We cannot enable e.g. CONFIG_BT as that would attempt
to pull in a lot of files we do not want in this test.
This commit also removes unused includes in the CMakelists
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Similar to logging and shell, allow application to override and
extend the ASSERT macros globally. This enables intercepting log strings
at the macro level for things like string tokenizations.
Signed-off-by: Kevin Zeng <zengk@google.com>
Removed conditional checks for device runtime put in DMA RX and
TX callbacks, ensuring that device runtime is always released
asynchronously.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This patch fix a reg write that needs to be done before calling the
callback. Since the user can start a new dma transfer in the callback,
it can miss the interrupt from the new transfer if the new transfer is
done before the interrupt bit is cleared.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Removed unnecessary power management state lock calls since the DMA is
on a power domain that already handles state locking.
It will now managed directly pm_device which will active power_domain
and then block pm_state.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Added calls to pm_device_runtime_put() to ensure proper device runtime
management when configuration or DMA transceive operations fail.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
This patch is needed to block the pm_state "PM_STATE_SUSPEND_TO_IDLE"
when a device on the power domain (actually all the peripherals) is
active. Without this patch, cpu can decide to go to deep sleep while
a peripheral is active.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Most drivers for Series 2 depend on clock control, but didn't
declare it. Enable clock control by default for Series 2 SoCs.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
The watchdog timer on SiWx91x devices is designed to
pause during deep-sleep and resume after wakeup.
However, an incorrect check in`wdt_setup` was
preventing this intended behavior. This patch removes
the check, restoring the correct pause-in-sleep
functionality.
Signed-off-by: Sai Santhosh Malae <Santhosh.Malae@silabs.com>
Relocate the contents of app.overlay into a board-specific overlay for
native_sim. This change prepares the codebase for adding regulator tests
for other boards.
Signed-off-by: Tim Pambor <tim.pambor@codewrights.de>
NuMaker watchdog control register is write-once after power-on
or reset. Thus, the control registeris written in the setup
function and the disable function only disables IRQ.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Set PPN (Physical Page Number) in L2 entry in the region_map_update
function to ensure correct mapping for memory that was not previously
mapped based on xtensa_soc_mmu_ranges.
When a new memory domain is created, the arch_mem_domain_init function
allocates new ptables using the dup_table function. This function only
copies original L2 entries created from xtensa_soc_mmu_ranges with
OPTION_SAVE_ATTRS. Entries added later by arch_mem_map are replaced with
XTENSA_MMU_PTE_L2_ILLEGAL and have PPN (Physical Page Number) set to zero.
When adding a new partition to a memory domain, the update_region function
is used. It sets new access attributes in the L2 table without setting the
PPN value. As a result, it does not work correctly for memory that was not
previously mapped based on xtensa_soc_mmu_ranges.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Add macro PTE_PPN_SET to simplify setting the physical page
number assigned in the page table entry.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Add macro PTE_PPN_GET to simplify retrieval of the physical page
number assigned to a page table entry.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Added PTP timestamping support in NETC ENETC host driver for no-tag
supported NETC switch.
On RX path, extended descriptor is used on host (pseudo MAC) to get
timestamp writeback.
On TX path, TX timestamp response should be enabled on host (pseudo MAC).
After TX, writeback TX timestamp ID should be updated to tx pkt fifo.
Once RX path received TX timestamp response, match TX timestamp to tx
pkt in fifo with the timestamp ID.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For NETC switch with tag support, PTP timestamping had already been
supported in tag driver.
This patch is to add PTP timestamping support for no-tag supported switch.
Timestamp functions are implemented and exported for host driver to
handle.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Converted to use NETC_PTP_TIMESTAMPING_SUPPORT for PTP timestamping.
PTP timestamping is needed only when NET_L2_PTP and PTP_CLOCK_NXP_NETC
are selected.
Used default 16 bytes for ETH_NXP_IMX_RX_RING_LEN for PTP timestamping
because RX extended descriptor would be used.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
PTP timestamping should be enabled only when NET_L2_PTP and
PTP_CLOCK_NXP_NETC are selected. And NET_PKT_CONTROL_BLOCK
is required for PTP timestamping code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch removes the use of sscanf to maintain compatibility with
tests that use the minimal cpp library. The expected version is now
defined using multiple individual values rather than a single
formatted string.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
C macro INSTR_FETCHABLE is missing parentheses in its definition,
this could lead to incorrect expansion when combined with logical
operators
Signed-off-by: Andrea Gilardoni <a.gilardoni@arduino.cc>
This is a negative detection. The conn index should be never out of
bounds of the array `connection`. Because the size of the array is
`CONFIG_BT_MAX_CONN`.
To improve the readability, add a `__ASSERT` checking to check if the
conn index is out of bounds.
CID 487769
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
This is a negative detection. The conn index should be never out of
bounds of the array `bt_sdp_client_pool`. Because the size of the
array is `CONFIG_BT_MAX_CONN`.
To improve the readability, add a `__ASSERT` checking here. Check
whether the conn index is out of bounds.
Fix#99985
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
There is a corner case that the connect complete event is notified
before the function `bt_hci_cmd_send_sync()` returns. Because the
created conn object is in the state of `BT_CONN_DISCONNECTED`, it
cannot be found in the connect complete event. As a result, the
connect can not established normally.
Fix the issue by setting the connect state and role before calling
the function `bt_hci_cmd_send_sync()`.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
