Update pic32cx_sg41_cult.yml to include DMA in the supported
features list.
Also enable the DMA controller node in pic32cx_sg41_cult.dts.
Signed-off-by: Arunprasath P <arunprasath.p@microchip.com>
Update pic32cx_sg61_cult.yml to include DMA in the supported
features list.
Also enable the DMA controller node in pic32cx_sg61_cult.dts.
Signed-off-by: Arunprasath P <arunprasath.p@microchip.com>
Add DT helper file for PIC32CX-SG family devices to support
SoC-specific device tree definitions and utilities.
Signed-off-by: Arunprasath P <arunprasath.p@microchip.com>
Remove nRF9160DK examples from Zephyr's cellular modem sample as
these use nRF91 as an external modem and the pin configuration
heavily depends on the build target.
Therefore we would like to host and document our own examples
within our own repository with the Serial Modem application.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Improve the logic for detecting counter wrap-around events when exiting
low power mode.
Add idle_timer_alarm_ticks variable to track alarm configuration at LPM
entry. Implement comprehensive wrap detection that considers:
- Counter overflow (pre > post)
- Alarm pending with same pre/post values
- Alarm pending when pre + alarm_ticks would exceed counter top value
This ensures accurate time calculation across all counter wrap scenarios
during low power mode transitions.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
- Add new hardware info driver for Microchip G1 series.
- Update Kconfig and CMakeLists.txt to support the new driver.
Signed-off-by: Farsin Nasar V A <farsin.nasarva@microchip.com>
- Added hwinfo node in the samd5xe5x.dtsi file.
- Added device tree binding file for Microchip HWINFO G1.
Signed-off-by: Farsin Nasar V A <farsin.nasarva@microchip.com>
The hwinfo driver should build inconditionally. It checks if the rstc
node is present and when CONFIG_HWINFO=y is selected by the user the
rstc information will be available. The fallback mechanism will provide
a weak implementation for all APIs that are not available.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The CMakeLists.txt file in the MTB HAL CAT1 module incorrectly appended
a '.c' extension to the source file reference for the 320 BGA pin package,
causing a build error.
Remove the extraneous '.c' extension to
correctly reference cyhal_xmc7200_320_bga.c.
Fixes#100523
Signed-off-by: Shreyas G Khanapur <ShreyasG.Khanapur@infineon.com>
Incorrect symbols were used for detecting nRF5340 Network-specific
reset reasons presence.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Update documentation comments to reference the correct function name
'bt_a2dp_register_ep' instead of the outdated
'bt_a2dp_register_endpoint' in SBC endpoint macro descriptions.
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Enable the CAP Commander role for the BT tester. This will
help pass some TMAP and GMAP tests that require the CAP
Commander to be enabled.
The actual implementation of the tests related to the
CAP commander is not implemented.
TMAP also requires that handover is supported if we
support both unicast and broadcast, so enable the config
for now. Support for the handover tests will follow in
a separate commit.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If spi_sam_configure() is called with more than 4 chip selects the
current check fails even if the pins are used as gpios. The variable
spi_csr_idx already has the correct index to be checked and must be
used in this check.
Signed-off-by: Munawar Ali <ali@sofiha.de>
Signed-off-by: Axel Utech <utech@sofiha.de>
If the image is not confirmed, there is no need to pad the entire flash
slot with empty data. This reduces the size of
`tfm_s_zephyr_ns.signed.bin` (the file actually sent for an OTA upgrade)
from 100% of the slot size down to the size of the application.
Signed-off-by: Jordan Yates <jordan@embeint.com>
If CONFIG_WDT_DISABLE_AT_BOOT is not defined (i.e. WDT should be enabled
at boot), DISABLE_WDOG should be 0 (disabled).
Signed-off-by: Alexandre Rey <alx.rey@icloud.com>
If the event timer or free-run timer is close to expiration when
system enters idle with I2C target DMA mode enabled, the memory
and CPU clocks may become unsynchronized after wakeup. This
causes CPU to fetch incorrect data and eventually trigger SoC
watchdog timeout.
Due to this hardware limitation, SoC should skip entering idle
mode if the remaining timer value is less than 150µs(safe margin).
Signed-off-by: Ren Chen <Ren.Chen@ite.com.tw>
Update segger with a change in SEGGER_RTT_Conf.h that allows to use
DT memory section for RTT data.
Added help section to SEGGER_RTT_SECTION_CUSTOM_DTS_REGION Kconfig
explaining what alias need to be added to DTS.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The accuracy field of lfocs lfxo is incorrectly parsed from the SVD
file. Instead of stripping the "ppm" from the value before converting
it to an int, we are taking only the first three digits. This works
for 500ppm, but not for 20ppm.
Patch to strip last three digits instead.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Where possible (i.e. not running in NS), erase the flash before testing the
write once secure storage API.
Signed-off-by: Pete Johanson <pete.johanson@analog.com>
Returning `-ENOTSUP` (and logging a `LOG_ERR`) is not the correct
behaviour if there is no enable GPIO. The fact there was no work to do
does not make the result an error.
From the docs for `pm_device_runtime_get`
```
* @retval 0 If it succeeds. In case device runtime PM is not enabled or
* not available this function will be a no-op and will also return 0.
```
Signed-off-by: Jordan Yates <jordan@embeint.com>
