MAX_PTHREAD_COUNT was deprecated in favour of
POSIX_THREAD_THREADS_MAX prior to v3.7.0.
Use CONFIG_POSIX_THREAD_THREADS_MAX going forward.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add a `--dry-run` (or `-d`) option to the posix kconfig
migration script for deprecated POSIX Kconfigs.
Additionally, add a set of skipped options (e.g. `TIMER`).
The `CONFIG_TIMER` option does not exist in the tree anymore
and was way too generically named previously, so the false
positive rate is astronomical, so it makes sense to skip it.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
There is an issue that the L2CAP connect response function
`l2cap_br_conn_req_reply()` is called first. And then the ACL
disconnect function `bt_conn_disconnect()` is called following. But
the packet of `bt_conn_disconnect()` appears on the HCI bus first.
Add a flag `L2CAP_FLAG_DISCONNECT_ACL` to flag whether it is needed to
disconnect ACL connection.
Set the flag `L2CAP_FLAG_DISCONNECT_ACL` when result of the L2CAP
channel conn rsp is `BT_L2CAP_BR_ERR_SEC_BLOCK`.
Add a l2cap packet sent out callback `l2cap_br_conn_rsp_sent_cb()`.
When the callback triggered, disconnect the ACL connect with
`BT_HCI_ERR_AUTH_FAIL` if the flag `L2CAP_FLAG_DISCONNECT_ACL` has
been set.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Do not start the LF clock unless CONFIG_CLOCK_CONTROL_NRF is enabled.
This is similar to how it's done in Nordic's GRTC driver.
Authored-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Export the currently used board name and (when applicable) qualifiers
and revisions to the EDK files. This information can be used by EDK
users who deal with multiple targets to differentiate between them.
Uses the existing 'zephyr_string' function to sanitize the strings
instead of a custom regex replace.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
The -imacros flag may be given in a number of different variations:
- with one or two preceding dashes, and
- separated from its argument, joined by an equals sign, or joined with
no separator
This patch fixes the handling of the -imacros flag in the LLEXT EDK to
detect all of those options.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
- added flag in nxp setup driver to perform HCI controller firmware-
load and configuration only once. This avoid loading/setting-up
controller fw on successive bt_init() after bt_disable() call.
Signed-off-by: Nirav Agrawal <nirav.agrawal@nxp.com>
- added HCI command to send hci-reset in bt_disable() func, and
remove its call from the driver close() call.
- remove rsp buf pass to 'hci_reset_complete()' func as status is
already checked under 'bt_hci_cmd_send_sync()'.
Signed-off-by: Nirav Agrawal <nirav.agrawal@nxp.com>
Adds a new shield definition for the Analog Devices EVAL-AD4052-ARDZ
accelerometer shield. This shield provides support for an ADI AD4052
16BIT adc over an Arduino SPI connector.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Initial AD405X driver supporting sampling, averaging
and burst averaging operation modes. Configurable
without interrupts or with device ready and
data ready interrupt.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
- Define i2c0, i2c1 bus nodes in the device tree for ZynqMP
- Note: Platform-specific configurations, such as I2C Bus Frequency and
Reference input clock, should be handled according to the design.
Signed-off-by: Ajay Neeli <ajay.neeli@amd.com>
Add a choice `BT_NXP_MODULE` to make sure only one controller can be
selected if the multiple controllers are supported.
All NXP Bluetooth module similar with BT_NXP_NW612 should be added
to the section.
And set the BT_NXP_NW612 as the default controller.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Added queue for memory slab addresses to ensure that they
are released in correct order. Improved formula for frequency
scaling for nRF54H20. Fixed alternative channel mapping.
Signed-off-by: Michał Stasiak <michal.stasiak@nordicsemi.no>
According to the datasheet, maximum conversion time for both
humidity and temperature at 14 bits resolution is 1.7 ms.
Signed-off-by: Ioannis Damigos <ioannis.damigos.uj@renesas.com>
Extend test code with scenario that checks if:
- RESET_CPU_LOCKUP is detected;
- RESET_CPU_LOCKUP can be cleared.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Protection circuit must be disabled to use NFCT antenna pins
as GPIOs. It can be done by adding nfct-pins-as-gpios to nfct
node in the devicetree in cpuapp. Node must be disabled as
NFCT is not used. In legacy platforms same property was added
to uicr node because that information was stored in UICR. In
nrf54h20 it is not part of UICR so property is part of nfct
node.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
In some configurations, code is copied from non-volatile memory
to RAM before a core (using that code) is booted.
When that core is reset by expired watchdog, variables shall be
restored to "initial" values.
This is problematic because the core is aware of copy in RAM.
It may not know address in non-volatile memory, where "original"
code is stored.
Add tests which verifiest that .bss and .data sections are
correct when core boots from reset caused by expired watchdog.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Add initial support for nuvoton numaker m55m1x SoC series
including basic init and device tree source include.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Added support for nRF54L20 PDK in tests involving
multiple instances. Corrected pin assignements in
spi_error_cases test.
Signed-off-by: Michał Stasiak <michal.stasiak@nordicsemi.no>
Add calls to sys_trace_idle_exit when leaving idle state. It is
used to track CPU load.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add new tracing API which is called when core is exiting from idle.
Current implementation is using it to track CPU load. Implementation
in tracing_none is now weak so it can be used if given backend does
not support new API call.
When CONFIG_CPU_LOAD is enabled then sys_trace_idle also calls a
hook which stores the timing information when CPU entered idle.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add module which can measure CPU idle time. Idle time is measured in
the pre/post CPU idle hooks but they are not provided by this module.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Setting frame size and endianess is now supported in UARTE HAL,
so these settings must have default values configured
to avoid compiler warnings about uninitialized fields.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Some of the CLOCK events are associated with features
not available on every nRF device.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
MDK 8.70.0 introduced following changes in the device naming:
- renamed nRF54L20 Eng A to nRF54LM20A Eng A
- renamed nRF54L09 Eng A to nRF54LV10A Eng A
Actual SoC renaming will happen in followup PR.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
It is observed that the regulatory domain API returns a failure
even when it has successfully completed its task. This change
addresses a minor fix to return the proper value to the user
when attempting to set the regulatory domain.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
VPR (FLPR) on nRF54L series has fixed issue with sleeping so
custom CPU idle function does not need to be used there.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
