MAX32658 is the 1.8V variant of MAX32657. From a software perspective,
both SoCs are functionally equivalent. Reuse the existing MAX32657
backend for MAX32658 to enable support with minimal changes.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Added mikrobus_serial, mikrobus_spi and mikrobus_header node labels
to FRDM-MCXA153 device tree board definition, allowing compatible
shield boards to be used.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Added arduino_i2c, arduino_spi and arduino_header node labels
to FRDM-MCXA153 device tree board definition, allowing compatible
shield boards to be used. Also extend the board YAML file with
related support tags arduino_gpio, arduino_i2c and arduino_spi.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Change SGI interrupt lines from 14-15 to 6-7 for nested interrupt
testing. SGI 8-15 are unaccessible from Non-Secure state (e.g., when
running with TF-A), causing test failures. SGI 0-2 are reserved for
Zephyr SMP IPIs, so use SGI 6-7 which work in both Secure and
Non-Secure configurations.
Fixes test failure: "isr0 did not execute" assertion at line 184.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
The driver should not take the whole interface down and re-initialize on
every low power entry and exit. This is a lot of latency for no real gain
as far as I can tell. We can just do as the reference manual actually says
which is to set the sleep enable bit to put the module to sleep while still
being able to detect magic packets for wake on LAN.
Also, the only platform that this power action was "enabled" for was
kinetis, but that platform does not have any power management enabled in
Zephyr. Which means this code was never getting called even with all the
PM configs on. So basically this code is dead code. But it could be useful
for other platform, such as RT, so there's no reason not to remove the
dependency on kinetis and let it be used for any of the platform as long as
PM_DEVICE is enabled (hence the imply).
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Adds initial SoC-level support for the Microchip
PIC32CZ CA80/9x series, including SoC definition files.
Signed-off-by: Mohamed Azhar <mohamed.azhar@microchip.com>
Adds common and SoC-specific .dtsi files for the Microchip
PIC32CZ CA80 CA90 and CA91 family. These files define core
peripherals, address maps, and interrupt controller structure
shared across the PIC32CZ CA80 9x variants.
Signed-off-by: Mohamed Azhar <mohamed.azhar@microchip.com>
Fix QSPI and half duplex
Support hold on CS flag
Create functions to assert and deassert CS
Signed-off-by: Benjamin Santon <benjamin.santon@analog.com>
Boards that use MCUboot to start XIP from external flash default to
CONFIG_CANOPENNODE_PROGRAM_DOWNLOAD=y. However, in the no_storage
sample, dependencies such as CONFIG_FLASH are disabled. This causes
build errors. Work around this by explicitly disabling program download
in the no_storage sample configuration.
Signed-off-by: Tim Pambor <tim.pambor@codewrights.de>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant. This avoids the
current situation where the same #include directive is duplicated among
many files, and where the file is sometimes included multiple times when
walking up the inclusion chain up until the root DTSI file.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Include <mem.h> from the series' root DTSI file and remove inclusion of
the file from other levels since it becomes redundant.
There is no consistency about which level of the DTSI inclusion hierarchy
the macros from this header start being used, so including it from the root
file ensures they are always visible and available without headache. Today,
there are places where the header is included twice or more at different
DTSI inclusion hierarchy levels because of this ambiguity - this commit
solves the issue once and for all.
Signed-off-by: Mathieu Choplain <mathieu.choplain-ext@st.com>
Explicitly cast down the string width to int, as otherwise it is
size_t which may have a bigger size.
Avoids the following build error:
subsys/net/lib/shell/dns.c:496:67: error: field precision specifier
‘.*’ expects argument of type ‘int’, but argument 4 has type ‘size_t’
{aka ‘long unsigned int’}
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
As the number of DMA channels could be different between DMA instances,
get the number from "XDMAC Global Type Register" and validate the
channel used.
Signed-off-by: Tony Han <tony.han@microchip.com>
When the XDMAC is activated in the DT, configure it's register region
with strong ordered, read and write access.
Signed-off-by: Tony Han <tony.han@microchip.com>
Product URL: https://www.microchip.com/en-us/product/SAMA7D65
The files under 'soc/microchip/sam/sama7/' will be used for both
sama7d5 and sama7d65 SoCs after the directory structure for sama7g5
is reorganized.
Signed-off-by: Tony Han <tony.han@microchip.com>
Replace the array size for sama7g5 registered clocks with macros and
put the macros to soc.h with descriptions.
Signed-off-by: Tony Han <tony.han@microchip.com>
