The erase mode for any external memory that is mapped to the address
space of the MCU is derived from the internal non-volatile memory erase
mode. In order to allow users to override the default value, add a new
--ext-erase-mode command-line option that takes an erase mode just like
--erase-mode does.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of providing an `--erase-pages` command, generalize it to a new
`--erase-mode` one that can be set to `none`, `ranges`, or `all`. This
gives the user full control over the erase mode that will be passed on
to nrfutil.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a "net filter" command that will allow user to see the
current network packet filter configuration.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make sure that we check possible network packet filtering status
before accepting the packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
As the network packet filter drops packets without any indication
that the packet is dropped, it can be difficult to monitor what
is going on in the system when receiving data. The user can
now monitor the statistics and see if packets are being dropped
because of packet filter activity.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The get_ip_rules() function is only used if IPv4 or IPv6
filtering is enabled so add checks to avoid unused function
warning.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
According to `f9901e8e` and validated by testing, the supplicant only
use case only requires 4 socket pairs. 6 pairs are required for the
`hostapd` use case.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Increase the verbosity of the message when there is no source address
in `net_context_create_ipv4_new`. This is likely the first failure point
when attempting to send data on an interface that has not yet been
assigned an IP address. Burying the fault at the DBG level makes it much
more time consuming to determine the root cause of this error.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The start_simple_cs_test and stop_cs_test depends on
CONFIG_BT_CHANNEL_SOUNDING_TEST and could cause build errors if that
is disabled while CONFIG_BT_CHANNEL_SOUNDING=y in the shell.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
I just happened to try to run this testsuite manually today and
noticed that it was being skipped due to a copy-paste error.
This test was migrated from tests/posix/common, where tests
were skipped for non-dynamic threads, since it would mostly
duplicate tests that had already been run.
However, while migrating, the condition to skip tests was
mistakenly left in when it should not have been.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
timer_create() will error if there are no dynamic threads to
run the SIGEV_THREAD handler, causing the test to fail (where
it was previously expected to pass).
Ensure that there is at least 1 dynamic thread available to
the POSIX API.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
If it is not possible to create a timer in timer_create(),
then the timer_obj associated with the timer must be freed.
However, the address of the pointer was mistakenly being
passed to k_mem_slab_free() rather than simply the
the pointer.
This caused a crash in tests which can easily be avoided
by passing the pointer rather than the address of the
pointer.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add initial support for the PocketBeagle 2 MCU domain Cortex-M4F core.
This only adds support for A0 revision (i.e. the version with AM6232).
PocketBeagle 2: https://www.beagleboard.org/boards/pocketbeagle-2
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
- AM6232 is a dual core variant of AM6234 with everything being smae.
- Used in the first batch of PocketBeagle 2
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
Adds the support for the STM32MP13 series to the existing STM32
Hardware Information driver.
Note that there is no LL_GetUID_Word<x> functions for the STM32MP13
series. to allow to use HAL_GetUIDw<x> functions create macros to
fill the stm32_uid structure.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
- Removing the unused declaration of 'ret'
in the usb_dc_stm32_init function for STM32N6.
- Ensuring the 'ret' variable is used correctly
in the pinctrl_apply_state function call.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
-This commit adds "sysbuild: true" for ns build-targets for the
following nordic board:
- nrf54l15dk (nrf54l10 target)
-Added missing vendor: nordic for some boards for consistency
Signed-off-by: Frank Audun Kvamtrø <frank.kvamtro@nordicsemi.no>
The number of ports in gptp_domain.default_ds.nb_ports is a uint8_t.
A pointer to it is passed to gptp_add_port.
However, in this method, the pointer is cast to an int pointer.
The C compiler generates an int-size store for this.
In addition to potentially overwriting adjacent attributes, on platforms
such as RISC-V that do not support unaligned accesses, this causes an
exception on access.
This commit casts nb_ports to the correct type, uint8_t.
Signed-off-by: Eric Ackermann <eric.ackermann@cispa.de>
thread_page_tables_get() is only used when userspace is
enabled. So move it with userspace #ifdef, or else
compiler would complain about it being unused.
Fixes#88421
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
PM_DEVICE_ISR_SAFE shall not be used when non-asynchronous API is used
because RX is disabled in suspend action and that takes relatively
long time. In case of PM_DEVICE_ISR_SAFE it is done with interrupts
disabled. RX is not used at all if disable-rx property is set and in
that case PM_DEVICE_ISR_SAFE can be used.
Added macro which determines if ISR safe mode can be used.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
z_tick_sleep function needs to calculate expected wakeup tick. It
required reading current system clock tick. It can be costly since
it is a register access. When timeout is added this value is
calculated and z_add_timeout returns it. It can be used instead to
optimize sleep performance.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add return value to z_add_timeout. It returns system tick when timeout
will expire.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Accessing system timer registers can be costly and it shall be avoided
if possible. When thread is waken up in z_tick_sleep it may be because
timeout expired or because thread was waken up before sleeping period
passed.
Add function to detect if timeout is aborted (before it was expired).
Use it in the sleep function and avoid reading system ticks if timeout
was not aborted.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Commit 38b8790 introduced a pretty bad regression for boards without
revisions. Fix by correctly checking for actually undefined revisions
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add an include of toolchain/common.h for the ALWAYS_INLINE
macro.
This is a general issue in many files across Zephyr, specifically
for the ALWAYS_INLINE macro, but for simplicity this commit
only includes it for this file as that has been shown to
cause compilaion issues without it.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Lack of PWM binding include causes some examples using this
shield not to build if the base board used did not already
include this binding.
Signed-off-by: Ian Morris <ian.d.morris@outlook.com>
