Some of the locks are created in supervisor mode (i.e. stdout one),
but should be accessed from user mode too. Unfortunately, there is
no way to distinguish these locks, so grant the access to all of them
as the actual reads and writes should end up as syscalls anyway.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
The ARC MWDT C library puts some constructors into .ctors section
to initialize its internal stdio locks. Enable the initializers
to make sure these constructors are actually executed.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
Use :c:func:`xxx` and :c:type:`xxx` when applicable, as well as reword
a deprecation to make the replacement appear.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Fix issues with Doxygen 1.14 and dark theme. Upstream PRs to
doxygen-awesome will be submitted in parallel.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Correct not resetting compression extension,
when checking for an uncompressed file,
in case if compression is enabled, but no compressed file found.
Signed-off-by: Andrey Dodonov <Andrey.Dodonov@endress.com>
In order to make it easier for folks to discover available twister
options when using/searching the documentation, or when making external
search in their favorite search engine, inline the output of
`twister --help` into the docs so as to have an always up-to-date
and searchable snapshot of it.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
With the four-channel-capture-support property enabled, the STM32 PWM
driver was missing every other frames during PWM capture.
The counter values are now reset just after getting the pulse and the
period of the cycle, instead of waiting the next interrupt to do so, and
thus missing a cycle.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
According to CoAP RFC (7252, ch. 4.2), Reset cannot be sent in a
response for an ACK reply, rejected ACKs should be silently ignored
instead. Therefore, in case an unrecognized response is received, verify
the response type before sending Reset.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The 'sys' argument in clock_control_renesas_ra_get_rate() is unused and
has been removed to clean up the implementation.
This also aligns with the function's actual behavior and eliminates
misleading validation logic.
Signed-off-by: Gaetan Perrot <gaetan.perrot@spacecubics.com>
Function spi_context_release reads the content of ctx->config without
checking first if it is set. In many drivers (including STM32), when a bad
configuration is made for the first transaction, ctx->config is not set,
and spi_context_release is called, resulting in hard fault.
This commit adds a check that ctx->config exists before reading it to
avoid this problem.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add a new promptless Kconfig symbol (INSECURE). This symbols must
be selected by any setting which is used to enable an insecure
feature.
Signed-off-by: Flavio Ceolin <flavio@hubblenetwork.com>
Fixed a bug where unconfigured clocks were connected to the can
interface in the device tree for SAM0, causing the interface to work
incorrectly. Fixed by adding the correct index when calling GENCTRL.
Also, the default divider has been reduced to 6 to allow setting
the bitrate to 500 kbps.
Tested on a canopennode sample on a board with an ATSAMC21E18A
microcontroller.
Signed-off-by: Vitaliy Livnov <vitaliy.livnov@devkit.agency>
Move the call to prepare_regulator_voltage_scale()
before PLL setup in clock_stm32_ll_h7.c.
This ensures the voltage regulator is configured
to the appropriate voltage scale before increasing
the system clock frequency via PLLs.
Without this change, the system configuration
may be out of spec.
Signed-off-by: IBEN EL HADJ MESSAOUD Marwa <marwa.ibenelhadjmessaoud-ext@st.com>
This introduces the release notes and migration guide for Zephyr 4.3.0
earlier so that people have a placeholder to start adding content as
they line up pull requests for the 4.3 release.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
The ieee802154_radio_send() function does not decrease reference counter
of the net_pkt, it's instead done one layer above in ieee802154_send().
This commit updates the mgmt functions using ieee802154_radio_send() to
always free the used net_pkt afterward.
Signed-off-by: Simon Piriou <spiriou31@gmail.com>
Coverity reported a memory - illegal accesses when using memset in
ataes132a_aes_ecb_block(). This can happen when the input block is
exactly 16 bytes: memset(¶m_buffer[19], 0x0, 0) is called. But this
is an undefined behaviour in C even if size is 0, as ¶m_buffer[19]
is an invalid pointer.
The fix consists of simply skipping memset() in this case, since there's
nothing to zero out.
Coverity CID: 434642
Signed-off-by: Loic Domaigne <tech@domaigne.com>
When the QSPI is used in dual flash mode, e.g. on the STM32H747I-DISCO
board, only the first flash memory was reset and configured in 4-byte
addressing mode. This was in particular causing data to be incorrectly
read from the second flash memory and only even bytes were valid during
a read.
The dual flash mode was only enabled after reading the SFDP table since
it is desired to read the table of only one flash memory, not both.
This commit changes the driver to only disable the dual mode temporarily
while reading the SFDP table, ensuring all other commands and in
particular configuration commands are sent to both flash memories.
Signed-off-by: Thomas Altenbach <altenbach.thomas@gmail.com>
IUT works as an RFCOMM Client. The peer device, RFCOMM server, is a PC
running bumble.
Add following test cases:
Case 6, RFCOMM MTU Size Data Send/Receive Test. To verify that the RFCOMM
client can correctly send and receive data packets that are exactly equal
to the negotiated MTU size.
Case 7, RFCOMM Data Transfer Exceeding MTU Size Test. To verify that the
RFCOMM client can reject sending and receiving data packets that exceed
the negotiated MTU size.
Case 8, RFCOMM Disconnect and Reconnect Test. To verify that the RFCOMM
client can properly handle a normal RFCOMM disconnection and successfully
reestablish the connection.
Case 9, RFCOMM Recovery After ACL Disconnection Test. To verify that the
RFCOMM client can properly recover when the underlying ACL connection is
abruptly disconnected, by reestablishing both ACL and RFCOMM connections.
Signed-off-by: Jiawei Yang <jiawei.yang_1@nxp.com>
IUT works as an SM Initiator/Responder. The peer device,
SM Responder/Initiator, is a PC running bumble on it.
Add shell commands to create and manage L2CAP server and channel with
different security level.
In the test suite, there are 5 test cases. The test matrix combines
each bonding flag:
| Test Case ID | Initiator | Responder | Expected Result |
|--------------|-----------|-----------|-----------------|
| BR_SM_Bonding_INIT_001 | Non-bondable | Non-bondable | Pass |
| BR_SM_Bonding_INIT_005 | General Bonding | General Bonding | Pass |
| BR_SM_Bonding_RSP_010 | Non-bondable | Non-bondable | Pass |
| BR_SM_Bonding_RSP_011 | General Bonding | Non-bondable | Fail |
| BR_SM_Bonding_RSP_014 | General Bonding | General Bonding | Pass |
Signed-off-by: Can Wang <can.wang@nxp.com>
IUT works as an SM Initiator/Responder. The peer device,
SM Responder/Initiator, is a PC running bumble on it.
Add shell commands to create and manage L2CAP server and channel with
different security level, reboot the board, and transfer data on the
SDP channel.
In the test suite, there are 28 test cases to verify SMP functions.
The test case list is:
- BR_SM_INIT_001: Basic Pairing with No Input No Output Capability
- BR_SM_INIT_002: Pairing with Display Only Capability
- BR_SM_INIT_003: Pairing with Keyboard Only Capability
- BR_SM_INIT_005: L2CAP Connection Failure After Successful Pairing
- BR_SM_INIT_006: L2CAP Server with Incoming Connection
- BR_SM_INIT_008: ACL Disconnection During Pairing
- BR_SM_INIT_011: Repeated Pairing Between Same Devices
- BR_SM_INIT_012: Security Level Escalation
- BR_SM_INIT_013: Multiple Channel Establishment
- BR_SM_INIT_017: Pairing Rejection by Remote Device
- BR_SM_INIT_018: Pairing Timeout
- BR_SM_INIT_021: Authentication Failure during Pairing
- BR_SM_INIT_022: Secure Connection vs. Legacy Pairing Fallback
- BR_SM_INIT_025: Rejection of Weak Pairing Methods
- BR_SM_INIT_028: Reconnection After Key Deletion
- BR_SM_INIT_029: Pairing with Delayed Response
- BR_SM_INIT_030: Stress Testing with Multiple Connect/Disconnect Cycles
- BR_SM_INIT_032: Power Loss Recovery
- BR_SM_INIT_034: Pairing During Active Data Transfer
- BR_SM_INIT_035: Pairing with Very Long PIN/Passkey
- BR_SM_INIT_037: Pairing with Peripheral Requesting Maximum Key Size
- BR_SM_INIT_039: Security Level Downgrade Attempt
- BR_SM_RSP_001: Basic Non-bondable Pairing with No Input No Output
- BR_SM_RSP_002: Display Only with Secure Connection
- BR_SM_RSP_003: Keyboard Only with Dedicated Bonding
- BR_SM_RSP_006: Security Level Enforcement
- BR_SM_RSP_008: L2CAP Connection with Security Level 1
- BR_SM_RSP_009: L2CAP Server with Security Level 2
Signed-off-by: Can Wang <can.wang@nxp.com>
IUT works as an SM Initiator/Responder. The peer device,
SM Responder/Initiator, is a PC running bumble on it.
Add shell commands to create and manage L2CAP server and channel with
different security level.
In the test suite, there are 10 test cases. IUT is configured
with Secure Connections Only Mode. The peer device is configured with
Secure Connections Mode or Legacy Mode. The test matrix is:
| Case ID | Secure Connection Option | Security Level | Expected Result |
|---------|--------------------------|----------------|-----------------|
| BR_SM_SC_INIT_005 | SC Only with SC | Level 4 | Pass |
| BR_SM_SC_INIT_006 | SC Only with SC | Level 1 | Fail |
| BR_SM_SC_INIT_007 | SC Only with SC | Level 2 | Fail |
| BR_SM_SC_INIT_008 | SC Only with SC | Level 3 | Fail |
| BR_SM_SC_INIT_009 | SC Only with Legacy | Level 3 | Fail |
| BR_SM_SC_RSP_005 | SC Only with SC | Level 1 | Fail |
| BR_SM_SC_RSP_006 | SC Only with SC | Level 2 | Fail |
| BR_SM_SC_RSP_007 | SC Only with SC | Level 3 | Fail |
| BR_SM_SC_RSP_008 | SC Only with SC | Level 4 | Pass |
| BR_SM_SC_RSP_009 | SC Only with Legacy | Level 3 | Fail |
Signed-off-by: Can Wang <can.wang@nxp.com>
IUT works as an RFCOMM Server. The peer device, RFCOMM Client, is a PC
running bumble on it.
Add shell commands to create and manage RFCOMM server with different
flow control mechanisms.
In the test suite, there are seven test cases:
Case 1: RFCOMM Server - Reject RFCOMM Session. IUT should properly
reject incoming RFCOMM session when BR connection is disconnected.
Case 2: RFCOMM Server - Forward compatible with Bluetooth devices that
do not send PN command. IUT should properly handle this case and use
FCON/FCOFF as flow control.
RPN, Test) and send NSC responses
Case 3: RFCOMM Server - Respond to Control Commands After DLC
Establishment. IUT should properly respond to control commands (RLS,
RPN, Test) and send NSC responses.
Case 4: RFCOMM Server - Information Transfer with Aggregate Flow
Control. IUT should handle information transfer with aggregate flow
control and properly issue flow control signals.
Case 5: RFCOMM Server - Information Transfer with Credit Based Flow
Control and Active Disconnection. IUT should handle credit-based flow
control and actively disconnect DLC.
Case 6: RFCOMM Server - Information Transfer with Credit Based Flow
Control and Passive Disconnection. IUT should handle credit-based flow
control and respond to DLC disconnection.
Signed-off-by: Jiawei Yang <jiawei.yang_1@nxp.com>
fix ulpm driver polarity issue.
when pin-pol set to falling need to set the POL bit to 1.
when pin-pol set to rising need to set the POL bit to 0.
Signed-off-by: Titan Chen <titan.chen@realtek.com>
The tests was written wrong. It was meant to test using same spi bufs
for both rx and tx, as in tree many sensor and other spi device drivers
use this paradigm. But the 2nd buf setup call was overwriting the first.
Fix by not using the helper function for this case.
And for the write back test, test using same spi_buf_set.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The STM32F7 family does not yet support power management in Zephyr.
Besides, LL_I2C_EnableWakeUpFromStop and LL_I2C_DisableWakeUpFromStop
are not implemented in the H7 HAL/LL drivers
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
- Change erase-block-size from 8192 to 4096 bytes to match
the 4 KB page size of STM32U3 flash.
- Update max-erase-time from 5 ms to 14 ms according to
datasheet specifications.
- These changes ensure correct flash erase behavior
and timing on STM32U3 devices.
Signed-off-by: Khaoula Bidani <khaoula.bidani-ext@st.com>
The Quectel BG95 binding currently marks mdm-power-gpios as
required. This fits designs that expose the PWRKEY pin, but the
BG95-M3 in Mini PCIe form-factor boots automatically via its
on-module “Automatic Power-On Circuit” and does not route
PWRKEY to the card edge.
Signed-off-by: Van Petrosyan <van.petrosyan@sensirion.com>
Replace memset() with an explicit loop to zero the data_buf array,
which is part of a volatile struct. Standard memset does not guarantee
volatile stores, which can lead to incorrect hardware access.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Some ESP32 images may not end with a segment whose
load_addr is 0xFFFFFFFF, especially if the flash was not fully
erased or the image tool does not write an explicit end marker.
This can cause the loader to process leftover or unrelated data as
additional segments, resulting in boot failures.
Update the IS_LAST() macro to treat any segment not matching
a valid memory region as the end of the segment list.
This ensures only valid segments are loaded and any trailing
invalid data is safely skipped.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
