As the net_dhcpv4_stop() will now properly remove DNS servers, remove
the loop check so that the add event gets tested again.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add information how the DNS reconfiguration API functions
dns_resolve_reconfigure() and dns_resolve_reconfigure_with_interfaces()
have changed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Print information which DNS servers were added by DHCP when
listing DNS servers in "net dns" command. This helps debugging
DNS server issues.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Remember which DNS server was added by a source like DHCPv4 or v6
message. This will allow system to remove DNS servers that were added by
that source. Then when stopping for example DHCP, we can remove those
specific DNS servers and not leaving DNS servers hanging in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Pins can be configured to retain their config even when the power
domain they belong to is suspended. Update pinctrl_nrf to enable
retain only if the pin has been configured and is not in use
(pincnf is low-power/sleep), disable retain otherwise.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The usage of nrf_gpio_port_retain_disable/_enable, in cases where
the soc pins support retention, every pin must be
retained/unretained regardless of what power domain the pad is in.
This patch ensures retain is applied to all pins in all domains by
the gpio_nrfx device driver, not only pins specifically in the
fast_active_1 domain. Without this patch, pinctrl will correctly
retain pins, while gpio_nrfx will fail to unretain them when
again.
We no longer check the output state either, which was passed with
the flags arg of gpio_nrfx_gpd_retain_set() so this arg has been
removed.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The STM32MP13 clock control has set and clear registers
for the clocks. So clearing the set register won't have any effect.
Instead, we should write on the clear register.
Signed-off-by: Julien Racki <julien.racki@st.com>
Use 64 bit values for accumulating idle time and measurement window
as it was possible to get overflow if window was long enough.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
From Zephyr SDK 0.17.1 the RX architecture is supported so
update the documentation of RX130 board to reflect this
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Excluding this test for qemu_rx because it's failing randomly
Root cause not identified yet, #92213 is created to keep track
of this
This test case is working fine on actual RX HW so issue might be
in the inside the qemu environment
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Ignore gapfill for RX target as some RX toolchains generate wrong
output image when running gapfill for binary format.
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The qemu_rx some how with too big offset in "mov" instruction
cannot manipulate the memory correctly
This commit reconfigure the slot count to reduce the size of
psa_global_data_t struct so that issue on qemu_rx not occur
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The qemu_rx is having issue with twister harness, command cannot
be send from twister test to qemu console, this commit temporary
disable them for further checking
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Somehow icount shift making this test fail on qemu_rx target
maybe clock rate on RX is too low, as work around I disable
the icount shift for this test case on qemu_rx
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
GCC for RX would crash with an internal compiler error during
DWARF frame generation in `dwarf2out_frame_debug_adjust_cfa()`
when compiling the `trigger_fault_illegal_instruction()`
test function.
This patch adds `__builtin_unreachable()` to help the compiler
reason about control flow, preventing incorrect DWARF CFA
generation.
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The prj.conf was missing CONFIG_COMMON_LIBC_MALLOC causing
warning of the depended config CONFIG_COMMON_LIBC_MALLOC_ARENA_SIZE
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Change noinit region to be after bss so that it would not cause
alignment issue for the data region setup
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The QEMU RX doesn't allow to write value to IR flag,
There is also mentioned in RX HWM that the IR should
not be write 1 to. So we change the method to trigger
interrupt here is to call directly to SW irq table
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The "p -= slab->info.block_size;" is causing the "p" pointer
to be underflow in RX architecture case, where the RAM address
start from 0x0, in some case p minus block size make it underflow
This change implementation uses an index-based reverse loop to
safely iterate over each block from last to first.
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The source code is missing the Receive enable in serial
poll-in function so the status flag will never become affect
and data will never be read
Add the RE write before checking for receive status flag
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
The RX linker is using the name "data" for .data region start
which caused the application cannot use "data" for variable
naming globally.
This commit change the name to "__data_region_start" as expected
in the linker_defs.h file
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
I'm not sure why this was necessary, but analyzing RX
executables was crashing with a divide by zero error on a
symbol which appeared to be duplicated in this list.
Signed-off-by: Keith Packard <keithp@keithp.com>
RX adds an underscore to all global symbols, so when we look for
log_const_ globals, we need to allow for that.
Signed-off-by: Keith Packard <keithp@keithp.com>
This architecture is missing lots of support bits. Stub out this piece so
we can get more things building.
Signed-off-by: Keith Packard <keithp@keithp.com>
I2S driver support standard format, short/long sync, left/right justified.
Supporting 2 channels as a default.
Signed-off-by: Lewis Lee <llee@ambiq.com>
Fixes these files to no longer delete non-secure partitions as
they are not present, and updates the offset of the area to use
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add LINKLAYER_PLAT_EnableBackupDomainAccess() and
LINKLAYER_PLAT_DisableBackupDomainAccess() to use Zephyr resources
that use a reference counter for access requests, for enabling
and disabling access the BackupDomain resources.
Bump hal_stm32 module to the revision integrating related stm32wba
BLE updates.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
