TI MSPM0 SoC series has General Purpose Timer and Advanced control timers
with Compare block which is used to generate time expiry and output
waveform like PWM. Add driver support for MSPM0 PWM output.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
When loopback mode is enabled, the output of transmit serial shifter
is connected to the input of receive serial shifter internally.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Add support to use DMA mode with cc23x0 SPI module. This consists in
specifying the DMA channels and peripherals.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Two DMA channels are assigned to TX and RX respectively:
- A TX DMA single request is asserted when there is space in the FIFO.
- A RX DMA single request is asserted when data is in the FIFO.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Earlier we had socketpair to pass wifi event information from
wpa_supplicant side to zephyr adaption layer. This is now replaced
by k_fifo to save some RAM.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Enlarge NUM_IRQS by 32 which is the number of interrupts for
SGI (Software Generated Interrupts) and PPI (Private Peripheral
Interrupts).
Signed-off-by: Tony Han <tony.han@microchip.com>
Obtain the divisor value for generate the corresponding MCKx from the
register instead of from the variable to avoid wrong result caused by
un-synced division ratios.
Signed-off-by: Tony Han <tony.han@microchip.com>
Obtain generic clock division ratio from the register instead of
from the variable to avoid wrong result caused by un-synced
division ratios.
Signed-off-by: Tony Han <tony.han@microchip.com>
Optimize sckc_get_rate() to be called without configurations in
parameter, the selection of slow clock of the timing domain directly
comes from the register.
Optimize sckc_get_status() with return value "CLOCK_CONTROL_STATUS_ON",
slow clock is always on either driven by the RC oscillator or by the
32.768 kHz crystal oscillator.
Signed-off-by: Tony Han <tony.han@microchip.com>
Create bus helpers that will send ccc commands as well as update
items within the i3c descriptor. These are different than the
direct ccc functions as these can give a bit of convience to also
updating the descriptor.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The issue is found when doing shell command "i2c scan" on sama7g54-ek.
In this case no data will be transferred besides START and STOP. Data
abort would occur on accessing "msg->buf[msg->idx++]" when MMU is
enabled and "msg->idx" is very large.
Signed-off-by: Tony Han <tony.han@microchip.com>
Fixes/adds jedec-id for is25wp128, is25lp064 and w25q512jvfiq flashes,
according to information from Flash data-sheets.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Add bus gpios to zephyr,user node in nrf overlays to enable testing
device_deinit test case.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add device_deinit test case which, in case there are two devices
using gpio loopbacks, deinits both controller and target devices,
then uses gpio to configure and toggle the pins of the bus, then
reinitializes both devices.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Adding supporting soc files for the k32lx platforms and updating
soc.yaml.
Signed-off-by: Ishraq Ibne Ashraf <ishraq.i.ashraf@gmail.com>
soc: nxp: kinetis: k32lx: Use device tree provided value
This clock frequency value will be defined in the board device tree.
Signed-off-by: Ishraq Ibne Ashraf <ishraq.i.ashraf@gmail.com>
CS hold time parameter is not correct which may cause bus fault
randomly.
System hang during status register reading after flash progromming which
is caused by parameter accessing in XIP mode.
Add dummy delay for READ command according the flash datasheet which is
required for SDR mode.
Use FlexSPI internal divider for clock updating instead of register in
CCM to avoid potential risk caused by flash access during clock updating
procedure.
Signed-off-by: Raymond Lei <raymond.lei@nxp.com>
MT35 flashes could run in octal mode, Now the driver doesn't support
octal mode, add octal mode support for MT35 flashes.
Signed-off-by: Qiang Zhao <qiang.zhao@nxp.com>
- Adds new tested NXP boards to the test_mcuboot platform_allow list.
- Sorts NXP boards alphabetically.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Updated documentation for Wi-Fi BT nxp shield.
Added information to build WPA supplicant based apps using this shield.
Signed-off-by: Abhinav Kulkarni <abhinav.kulkarni@nxp.com>
Replace IC specific fuel gauge example with a generic fuel gauge example
and move the fuel gauge sample to sample/drivers folder
Signed-off-by: Philipp Steiner <philipp.steiner1987@gmail.com>
