"LL only" is not the only config option of potential interest, e.g. the
public address is also important.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This allows HCI drivers to expose vendor-specific functions to set the
public address.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Previously, the idle bit would be read for X amount of times. This
could vary alot depend on the CPU speed. Timeout is now to happen
from the cycle time.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Just in an effort to reduce notifications in areas that I'm not
super actively involved in. I was getting a lot of false
positive notifications for sensors.
Feel free to ping me for individual reviews on
simplelink parts or TI HAL or radio drivers.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
Code uses local RAM buffer to properly handle the case where provided
USB transfer TX data is not in RAM.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
There's a ternary operator that depends on configuration-defined macro:
`CONFIG_DYNAMIC_INTERRUPTS` is not enabled by default
for any of the platforms that use PLIC,
it is possbile to set it to `=y` though.
This triggered the Coverity check to report it as dead code.
Fixes#65576.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
The b_u585i_iot02a stm32 board has no HTS221 DRDY pin
to trig the HTS221 relative humidity and temperature sensor
So that sample.sensor.hts221.trigger is not applicable.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commits provides USART PINCTRL configuration for efr32_radio_brd4180a
and efr32_radio_brd4187c boards.
Signed-off-by: Franciszek Pindel <fpindel@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commit increases the length of ring buffer that holds serialized
nRF 802.15.4 API calls so that it can simultaneously store all
notifications the driver is capable of issuing. Currently that's not the
case, which creates a possibility of the serialization buffers running
out while the driver is issuing notifications.
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
pthread_cleanup_push() and pthread_cleanup_pop() are required
by the POSIX_THREADS_BASE Option Group as detailed in Section
E.1 of IEEE-1003.1-2017.
The POSIX_THREADS_BASE Option Group is required for PSE51,
PSE52, PSE53, and PSE54 conformance, and is otherwise mandatory
for any POSIX conforming system as per Section A.2.1.3 of
IEEE-1003-1.2017.
In this change, we require the addition of a dedicated
pthread_key_t that will not be available for applilcation usage.
Rather than including that as part of
CONFIG_MAX_PTHREAD_KEY_COUNT, we increase the storage by 1 in
order to be least invasive from the application perspective.
Signed-off-by: Christopher Friedt <cfriedt@meta.com>
This commit provides support for changing PLCA parameters stored in
lan865x_config_plca structure.
After values are updated, the LAN865x needs to be reset and then
configured with new values.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The Zephyr's core ethernet code had to be adjusted to support setting T1S
PLCA parameters from user Zephyr programs.
Such approach allows more flexibility, as T1S network configuration;
especially PLCA node numbers, can be assigned not only via device tree
at compile time. For example user can read them from EEPROM and then
configure the network accordingly.
For now - the union in struct ethernet_t1s_param only consists of plca
structure. This can change in the future, when other T1S OA parameters -
like Receive/Transmit Cut-Through Enable (bits RXCTE/TXCTE in OA_CONFIG0
register) are made adjustable from user program.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The LAN865x device after HW reset supports only the non-protected control
transmission mode. When it is reset alone - without resetting already
configured HOST system - one must assure that in HOST's OA TC6 driver
the protection SPI transmission support is disabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The ctx->reset member of struct lan865x_data shall be cleared each time
one wants to reset the LAN8651 device.
Before this change this value was only initialized in the lan865x_init().
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change allows modification of the PLCA configuration in the lan865x
driver.
Values in this structure can be set via device tree as well as modified
by the user program.
Without this change the latter use case would not be possible as the
struct lan865x_config structure is defined as read only and its data
is only provided by device tree.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
(Not to mistake it for the dynamic power control nor the zephyr LL
vendor-specific commands controlling local tx power) this yaml addition
will build the shell code for the LE Power Control Feature API's, acting
as verification.
Signed-off-by: Kyra Lengfeld <kyra.lengfeld@nordicsemi.no>
As other helper functions were introduced for the LE Power Control
Request Feature (see CONFIG_BT_TRANSMIT_POWER_CONTROL), it was noticed
that the return statements of switch cases should be on the next line
generally. This will align phy2str with the rest in bt.c.
Signed-off-by: Kyra Lengfeld <kyra.lengfeld@nordicsemi.no>
To use LE commands of Le Power Control Request Feature one must utilize
the BT_TRANSMIT_POWER_CONTROL config.
Signed-off-by: Kyra Lengfeld <kyra.lengfeld@nordicsemi.no>
This commits adds the LE API's for the LE Power Control Request Feature
in Zephyr.
The support of feature is provided with the controller-based feature
selection with BT_CTLR_LE_POWER_CONTROL_SUPPORT and is selectable via
BT_TRANSMIT_POWER_CONTROL.
With the new APIs, the applications will:
get improved reading of local and remote tx power
be aware of changes in remote or local tx power
Defined HCI commands in Core Spec v5.4:
7.8.117 LE Enhanced Read Transmit Power Level command:
improvement to existing local tx power reading.
7.8.118 LE Read Remote Transmit Power Level command:
Remote tx power is read through an event (LE Transmit Power Reporting)
7.8.121 LE Set Transmit Power Reporting Enable command:
Enables local or remote tx power reporting to monitor changes in tx power
7.7.65.33 LE Transmit Power Reporting event
Note: to utilize the Feature fully Nordic-LL-only vendor-specific commands
are needed. These will not be added in RTOS zephyr but instead
implemented in a maintainable way in sdk.
Signed-off-by: Kyra Lengfeld <kyra.lengfeld@nordicsemi.no>
Add a step to the first twister shard to upload the list of Python
packages used with the build.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Configure the unused pin as GPIO_DISCONNECTED for saving the power
consumption with the gpio-hog feature. The STM32 GPIO driver will
configure the pins as analog.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add an extra optional input to the script which can be used
to pass more options to cmake.
Background: With sysbuild needing to pass extra options is quite
normal. Users would normally want to add options, without necessarily
wanting to change the default cmake_args, so this new options
provides that.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Instead of performing a set of relative address comparisons using
pointers of type 'uint8_t *', we leverage the existing IN_RANGE()
macro and perform the comparisons with 'uintptr_t'.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
Add overlay to show how to use new experimental nxp enet driver
Also make any eth_mcux related kconfigs dependent on eth_mcux in the
boards' defconfigs.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add driver for NXP ENET which is a rework of the old
eth_mcux.c driver which had become unmaintainable due to
fundamental problems with the lack of PHY abstraction.
eth_mcux.c and the corresponding compatible nxp,kinetis-ethernet
will be deprecated and this new driver will be supported instead.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add Driver for KSZ8081 Ethernet PHY. The Generic MII Driver
is not sufficient to use for this PHY chip which has special
vendor implemented behaviors.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add a property to the ethernet controller binding
indicating what type of connection the MAC has with
the PHY device.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
