The PAN1783A-PA evaluation board is a development tool for the
nRF5340 from Nordic Semiconductor and the third evaluation
board variant for the PAN1783 Module. The power amplifier (PA)
version includes FEM support.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
When Power Management is enabled (CONFIG_PM=y),
the CONFIG_IDLE_STACK_SIZE of 320 is not enough :
Increase its size to 512.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
The defconfig.series file for the stm32f4 incorrectly redefines
the PM Kconfig in order to select two dependencies, COUNTER and
COUNTER_RTC_STM32_SUBSECONDS, instead of setting a default for
them if PM is included.
This commit fixes the error described above.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
The esp32c3 systimer has been fixed in PR #53453, but stamp_c3 was
not included, so we will update it to catch up with this fix
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Some STM32F4xx chips have an R division factor in PLL. Add possibility
to configure that.
Even though the output from the R division is not used, it can be
increased to reduce power consumption.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This change adds support for enabling ethernet MAC hardware checksum
offloading for STM32H7 based devices.
In Section 58.5.9 of the STM32H7 reference manual it mentions that
the STM32H7 ethernet MAC supports a Checksum Offload Module (COE).
I have tested the changes on my end where I enabled
CONFIG_ETH_STM32_HW_CHECKSUM and ensured that an application that
runs Zephyr on the STM32H7 can interoperate with a device with a
completely different implementation. Also, I deliberately made
the software not populate the IPv4 and UDP header checksum fields
in their respective headers and the COE was able to populate the
IPv4 and UDP header checksums.
Given that CONFIG_ETH_STM32_HW_CHECKSUM is not enabled by default
application developers have the option to either enable it or
disable it.
Signed-off-by: Chamira Perera <chamira.perera@audinate.com>
Add the possibility to flash nucleo-l4r5zi board using west
STM32CubeProgrammer runner.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Corrects the size of the external octoFlash connected to the
mcu of the stm32h573i disco kit from STMicroelectonics
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Reduce code-complexity of stm32_clock_control_init() function, which is
used and exists for both M4/M7 cores.
Replace dublicated code by proper preprocessor guarding.
This change shall reduce code-errors and copy-paste errors since same
functional code is present only once now.
Identify even more common code
Signed-off-by: Alexander Kozhinov <ak.alexander.kozhinov@gmail.com>
Set suspended as initial power state, only when the
CONFIG_PM_DEVICE_RUNTIME config is enabled.
The initial state was incorrect, when CONFIG_PM_DEVICE=y and
CONFIG_PM_DEVICE_RUNTIME=n. In that case, the power state was SUSPENDED,
but the device was actually enabled.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Updated API version enables multi-instance GPIOTE driver.
Additionally obsolete symbol that was used to specify
API version in the past was removed.
Affected drivers have been adjusted and appropriate changes
in affected files have been made.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
After adding new GPIOTE instances, there is a need
to enable the instance for individual boards.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Added GPIOTE0, GPIOTE1 instances for legacy devices,
GPIOTE20, GPIOTE30 for Moonlight and GPIOTE130,
GPIOTE131 instances for Haltium.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Change the GPIOTE driver to HAL to prevent instantiation
issues with a multi-instance GPIOTE driver.
Signed-off-by: Jakub Zymelka <jakub.zymelka@nordicsemi.no>
Like the stm32H5, stm32u5 usb device has an independent
power supply, but control bit is PWR_SVMCR_USV.
The control bit for the stm32H5 is PWR_USBSCR_USB33SV (no change)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This driver supports few different hardware configurations, add a
document page showing some of them next to some schematics snippets
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Replace the GCC-syntax attributes used for LL_EXTENSION_SYMBOL
with the toolchain-independent versions provided in toolchain.h
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The elf64_sym structure was defined as having the members order
as the elf32_sym structure, which is incorrect.
Use the correct layout as defined by the ELF specification
(see https://refspecs.linuxfoundation.org/elf/gabi4+/ch4.symtab.html)
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Add reference to section in RTC peripheral documentation which
covers the emulated RTC.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
The incorrect semaphore was used for the ipc1 instance to synchronise
the data receiving.
This commit fixes it.
Signed-off-by: Marcin Jelinski <marcin.jelinski@nordicsemi.no>
Added `OT_PLATFORM_POWER_CALIBRATION` and set to always off
as in Zephyr power calibration is handled by Radio Driver.
Signed-off-by: Maciej Baczmanski <maciej.baczmanski@nordicsemi.no>
- board.cmake is augmented for LinkServer (now the default runner
for this board)
- the board's doc file is updated as well
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
- board.cmake is augmented for LinkServer (now the default runner
for this board)
- the board's doc file is updated as well
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
In sys_clock_set_timeout(), input "ticks" is used to compute next
timeout point, Ambiq's STimer API used to sets next timeout has input
parameter as ui32Delta, which inside the API is using
"this value to add to the STimer counter and load into the comparator
register" according to its spec, thus the this delta clock is
almost equivalent to input "ticks"'s concept, and is not related to
last_count, it should be computed directly from input "ticks".
This correction fixes the test case failure at
zephyr\tests\kernel\tickless\tickless_concept.
Signed-off-by: Bryan Zhu <bzhu@ambiq.com>
This Kconfig is seemingly unused with exception to a single board,
whose maintainers have been unresponsive for a long time. It is
not useful to any other board and can be set in dts, therefore
deprecate it and schedule removal after the Zephyr 3.7 release
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Using SDL_DISPLAY_ZOOM_PCT would cause mouse pointer/touch input
to not click at the correct position.
Signed-off-by: Jakob Krantz <mail@jakobkrantz.se>
Fixed several headings in the contribute section that were not following
the documentation guidelines for headings.
Signed-off-by: Grzegorz Ferenc <Grzegorz.Ferenc@nordicsemi.no>
Currently SOF has disabled CONFIG_PM_DEVICE_RUNTIME_EXCLUSIVE option and
use pm_suspend_devices() to suspend and resume IPC device during D3
power flow. The pm_suspend_devices() function skips suspending devices
that are busy. In very rare cases, the IPC device is busy during the
power state transition, which results in the device not being restored
during reboot. This happens when FW sends a message to the HOST and
waits for ACK, and the HOST simultaneously sends a SET_DX message to the
DSP. This suspend/resume logic in IPC driver does not work well when the
system enters the D3 state because it is not a suspend state, but rather
a power-off. IPC does not require suspending, only reinitialization when
exiting D3. We cannot avoid this one missing ACK and it cannot block the
DSP from turning off.
When FW receives a SET_DX message it checks whether it can enter the D3
state and then returns an error (via IPC) or calls the pm_state_force
function. Success response is sent directly from power_down assembly and
not via ipc driver. This is because after receiving the response, the
HOST will turn off the DSP.
In order for the transition to D3 to take place, only the primary core
can be active, all pipes must be stopped (and therefore all modules in
FW). The only active thread at this time is the Idle thread. Driver on
the host will not send another ipc because is still waiting for
response. FW can try to send only two notification:
- FW exception: from this place there is no return to continue the power
transition,
- log buffer status: skipped, they remain in the queue without being
sent.
I'm moving pm_device_busy_clear(dev) from IRQ handler to
intel_adsp_ipc_send_message function so the pending ACK does not block
power transition.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
The help text uses the capital case as its an acronym, but passing
capital case fails. Also extend that to others as well.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
For better readability, below rules will help:
* Each command should be separated by a newline
* Each command should end with a full stop (intermediate statements
shouldn't have full stops)
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
