Updated the driver to start with a value to compare the counter
with otherwise the counter will not start until the user sets
the top value manually, an issue that will occur inside the counter
test.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Added a single instance lptmr node on the
mcxn947 soc dts. Updated counter lptmr to
have max value property.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
- Optimize slot sizes for MCUBoot swap move algorithm
for mimxrt595/685_evk boards.
- Use DT_SIZE_K/M macros for slot sizes.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
ull_adv_sync_pdu_set_clear does pretty much everything, causing
it to be very complex and awkward to use. In addition, it only handles
a single PDU, meaning callers have to handle the chain.
It has been replaced with simpler, more complete functions for handling
the relevant operations
Fixed issues include:
- Fragmentation of adv data over HCI is now decoupled from PDU
fragmentation, fixing HCI/DDI/BI-13-C, LL/DDI/ADV/BV-26-C and
LL/DDI/ADV/BV-55-C
- Adding BigInfo now preserves the PDU chain
- Enabling periodic advertising with ADI on would sometimes fail
due to insufficient space in a single PDU to add ADI
Signed-off-by: Troels Nilsson <trnn@demant.com>
When dumping logs from the `--inline-logs` option, remove any coverage
information that may be contained in those logs. Coverage dumps are
unrelated to any test failures and make it harder to find the failing
test information. In extreme cases the relevant information is lost due
to terminal scrollback limits.
If the raw dump information is required, it is still present in the
original `handler.log` file.
Signed-off-by: Jordan Yates <jordan@embeint.com>
These macros tend to be defined by too many headers.
Let's guard these definition with ifdefs to avoid
redefining them to practically the same.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
that utilizes the fact that the ldpc recovery matrix is triangular and only
stores the half with non-zero values.
This implementation is hopefully going to make forward error correction
usable on lower memory devices.
Signed-off-by: Lucas Romero <luqasn@gmail.com>
to no longer be a long-lived status variable because we already map it into
is_active and this reduces the number of states the transport can be in.
It also helps us prepare for being able to plug in more decoders by
removing implementation specific bits from the general transport interface.
Signed-off-by: Lucas Romero <luqasn@gmail.com>
Erase and reset must run only once during flashing.
This prevents a situation, where the next flashed image erases the
previous one.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Add support for GPIO controlled disconnect pullups. This is used in F1
based devices, copied from the legacy driver.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
For slow processors it is possible that setting 1 ms alarm and
then canceling it could lead to alarm expiring before it is canceled
and that was not expected in the test. Increasing timeout to 1.5ms.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This driver can be used for both mcux and
s32k series SoCs which have flexio IP.
PWM channel is automatically allocated by
flexio driver based on the available timers.
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Enable the mac node along with the necessary pinmuxing to enable the
ethernet and usb hs peripheral. I additionally defined the
`ethernet_phy_en` node the uses a fixed regulator to release
the PHY reset.
Additionally an usb_cdc_acm node was defined to enable serial over usb for
the console.
Signed-off-by: Rahul Arasikere <arasikere.rahul@gmail.com>
Enabled the QuadSPI node and necessary pin muxing to enable interfacing
with the external flash chip on the Portenta H7 board. The jedec data was
validated with the samples/drivers/jesd216 project to extract the
JEDEC data.
Additionally added `flash` to the list of ignored tags as the flash driver
should not be built on the M4 CPU domain.
Signed-off-by: Rahul Arasikere <arasikere.rahul@gmail.com>
Enabled the flash memory controller node along with the necessary pin
muxing. This allows us to interface with the additional 8MB of external
SDRAM available on the Portenta H7 board.
This has been tested minimally with the tests/drivers/memc/ram test.
Signed-off-by: Rahul Arasikere <arasikere.rahul@gmail.com>
Previous clock frequencies were taken directly from the arduino example
and were limited to 96 MHz and 48 Mhz for the CM7 and CM4 respectively.
Updated the clock tree to take advantage of the faster clock speeds.
Introduced two board revisions as revision 1 of the portenta board does
not have the external LSE oscillator populated (default) and version 4.1
onwards does have the external oscillator populated. The user can choose
to build support for the required clock configuration using the revision
scheme built in to west. Updated the docs to reflect the same.
Signed-off-by: Rahul Arasikere <arasikere.rahul@gmail.com>
Distinguish between test case dependencies where a board has a test
feature "usbd" and where no dependency is required other than the
devicetree overlay file, as here to build the UDC skeleton driver.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
We have recently added a new platform where the USB controller is only
supported in the new USB device support. This forces us to introduce a
new supported feature tag to distinguish the dependency. Use "usbd",
which is also the prefix of the new device support.
There are many boards that already have new driver support, but we will
replace the "usb_device" feature when the old device support is
deprecated.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Expands driver to cover nRF54L15 features like AIN as GPIO configuration,
new reference voltage, different set of supported gain options.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Fix KSZ8081 binding properties:
- reset-gpios and interrupt-gpios are generally standard
properties and therefore should not be using a special name
- mc, is not the correct vendor prefix for microchip
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Fix simple bus reg / ranges warning from GPIO
nodes by giving the parent nodes addresses
and describing a ranges other than empty.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Clarify eSPI reset bus event convention, which follows eSPI
physical reset pin.
Clarify eSPI OOB packet length expectations for eSPI driver
clients and eSPI drivers implementation
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Updates the `platform: ADI` area to match max32 drivers, dts, and soc
files that were recently introduced.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
