The mutex was removed in tcp_recv() where it doesn't seem
to be needed anymore as tcp_conn_search() got
tcp_mutex. In the other areas the tcp_mutex was
narrowed down to protect only the list.
Signed-off-by: Daniel Nejezchleb <dnejezchleb@hwg.cz>
During stress test with WiFi connect, disconnect, ping and throughput
traffic, ARP table updating failed issue may occur.
In arp_prepare(), if packet allocate failed, should add the arp
entry back to arp_free_entries, to avoid this entry is leak forever.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
The comments for `index` and `num_colors` in `struct led_info` were
mistakenly swapped. This commit corrects them to accurately reflect their
actual purpose.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Fix up the BUILD_ASSERT so that it does not trigger if the resolution
cpi is not specified in the devicetree and left to the default value.
Also use the correct spelling for "cpi".
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Both VEVIF and BELLBOARD test cases are unidirectional from the core
executing the test (cpuapp). For VEVIF, cpuapp pings, and for BELLBOARD,
cpuapp pongs.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The bonding info is not loaded after the Bluetooth
initialization again.
Call settings_load after the Bluetooth initialized.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
For command zperf udp download 5001 192.168.10.1,
zperf will bind both ipv4 and ipv6 sockets on ipv4 address.
But bind ipv6 socket will fail, thus command return fail.
Fix it by check ip address when zperf download.
For ipv4 address only bind ipv4 socket.
For ipv6 address only bind ipv6 socket.
For unspecific address bind both ipv4 and ipv6 sockets.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
Due to number of IRQs the ROM offset, that contains MCUboot,
needs to be moved to address that is aligned with 2048 byte
long vector table.
This comes from Cortex-M requirement where vector table needs
to be placed at offset equal to lowest power of two number
that will fit vector table.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Signed-off-by: Mateusz Michalek <mateusz.michalek@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add checks for vendor specific data path in ULL and HCI driver, to
enable use of vendor data path for BIS reception.
Signed-off-by: Morten Priess <mtpr@oticon.com>
- Calculate broadcaster channel for control subevent
- Calculate sync receiver channel for control subevent
- Fix broadcast CSTF only set in first subevent
- Remove ctrl_chan_use from LLL, as there is no longer a reason for
storing it.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Update the legacy low latency variant of the ticker
implementation to skip to next periodic interval when
ticks to expire is behind the current tick. This makes
the low latency variant of the implementation consistent
with the default ticker implementation.
Also, cleanup conditional compiles in the implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Unlike the remainder of the RT10xx series, the RT1011 SOC requires that
the flash configuration block be placed at an offset of 0x400 bytes,
instead of the start of the flash.
Fixes#70090
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
If I2C recovery mode uses GPIO push-pull to drive(3.3v), it will result
leakage in a pull-up voltage of 1.8V on the power rail, leading to
damage to 1.8V devices, including SoC, sensors.
Therefore, the recovery mode should be changed to GPIO open-drain type
to avoid this.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
My recent change overlooked this configuration, which is not tested in CI
currently.
If someone had enabled it, they would've just gotten an unfixable assert.
The correct test would be checking if the current thread is the system wq,
but I think the compiler can't know that and can't remove the "dead" code.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Add support for devices that use the kinetis
GPIO/PORT scheme but with the slight modification
that the interrupt control bits are in the GPIO
peripheral instead of the PORT peripheral.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The enum define is not implemented with the same name on all SoC's.
Use the register define instead.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. Add support to enable PORT control clocks
2. Add support for LP Flexcomm
3. MCX family has a different Clock API for USDHC.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The Low Power Flexcomm driver manages the interrupt handling
and provides an API to register interrupt callbacks.
Register the NXP LPUART interrupt handler.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. This driver allows to configure the Low Power Flexcomm
interface as a UART, SPI or I2C device.
2. Manages the interrupts and dispatches it to the
appropriate device driver.
3. A Flexcomm interface can be configured to be used as
I2C and UART device. However a SPI device cannot be used
concurrently with I2C or UART. Add checks for this feature.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This binding is for the NXP FlexComm Interface. The
driver will setup an interface for use as a UART, SPI
or I2C device.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
RD RW612 BGA board is built targeting secure mode execution. If
CONFIG_TRUSTED_EXECUTION_SECURE is not set, base address declarations in
CMSIS header files will be incorrect, causing a variety of issues. Fix
this.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add connect match for dialing PPP connection.
Ensure PDP authentication is disabled.
Request manufacturer, firmware version, and IMSI from the modem.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Add new commands to manage the Encrypted Advertising Data feature.
Overview of those new commands:
- `bt encrypted-ad set-keys`: set key materials (session key and
initialisation vector) used for encrypted and decryption of EAD;
- `bt encrypted-ad add-ad`: store a given advertising data structure;
- `bt encrypted-ad add-ead`: encrypt the given advertising data
structres and store the generated AD structure;
- `bt encrypted-ad commit-ad`: set the AD of the selected advertiser
with the stored AD;
- `bt encrypted-ad clear-ad`: remove all stored AD;
- `bt encrypted-ad decrypt-scan`: decrypt data using the previously set
key materials when receiving AD with type `0x31`.
The documentation of the Bluetooth Shell has been updated to include
those new commands.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Spawns n instances of the bt-shell in separate xterm windows.
Assumes in-tree build of the shell, can optionally specify another .exe
image.
Also add snippet for that use-case (`-S xterm-native-shell`).
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
For breaking API changes, let's mention explicity the PR should
be labelled with the "Architecture Review" label, as that is
the one we base the automation on.
As otherwise it is not clear enough for developers that they
should add it, and without it (and the automation surrounding it),
it is too easy for a PR to be merged by mistake.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Support MCI_IO_MUX pinctrl in LPC GPIO driver
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Co-authored-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
