Qualification test CSIS/SR/SP/BV-03-C [Lock Timeout]
Specification: Coordinated Set Identification Service Revision v1.0.1
Section 5.3.1.1.
When the server and the client are not bonded and they disconnect when
the value of the Set Member Lock characteristic is set to Locked, the
server shall set the value of the Set Member Lock characteristic to
Unlocked immediately after the disconnection.
Signed-off-by: Henrik Eriksen <heri@demant.com>
Qualification test MICS/SR/SPE/BI-01-C [Invalid Mute Value]
Specification: Microphone Control Service Revision v1.0 Section 3.1.1
If the client writes a value of Disabled or RFU to the Mute
characteristic, the server shall return an ATT Error Response with the
ATT error code Value Not Allowed (0x13) as defined in Assigned Numbers.
Signed-off-by: Henrik Eriksen <heri@demant.com>
The timing_max parameters defined in the stm32 bxcan driver don't match the
register description in the reference manuals.
- sjw does have only 2 bits representing 1 to 4 tq.
- phase_seg1 and phase_seg2 max is one tq higher.
I have checked the following reference manuals and all match:
- RM0090: STM32F405, F415, F407, F417, F427, F437 AND F429
- RM0008: STM32F101, F102, F103, F105, F107 advanced arm-based mcus
- RM0351, RM0394: all STM32L4
- RM0091: all STM32F0 with CAN support
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The API was never implemented.
The channel type can also be obtained using bt_iso_chan_get_info().
If we would have to implement this API, it would share a lot of the
implementation with bt_iso_chan_get_info().
Removing the API makes the ISO APIs more similar to the ACL APIs
where we don't have a special API to fetch the role.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
RD-client tests should wait longer for expected events.
Also the stubbed service worker should be stopped properly
after tests.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Bootstrap executable cause socket to be closed, so
it requires some delay for Ack to be send out as well.
Similarly, add small delay for Update trigger, so the
possible Ack goes out before the actual update message.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
When BOOTSTRAP FINNISH message was received, it caused
engine to immediately switch to BOOTSTRAP_TRANS_DONE state
which then closed the connection.
Ack packet was still on the send-queue so it never got send before close().
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Some state changes were do by directly writing into
client.engine_state variable, followed by call next_event_at(0);
This causes hard-to-find side effects.
Refactor all state transitions to use set_sm_state() to have better
control for it.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Following #60410, the NXP S32 external interrupt controller device
initializes after the core interrupt controller. Bump the NXP S32 intc
init level to initialize after the core intc and before the GPIO
device driver.
Fixes#61218
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Test fixed group address acceptance condition, which has been clarified
in Mesh Protocol 1.1: A node shall deliver a message to the model
subscribed to a fixed group address even if the corresponding feature
is disabled.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Reduce the main clock frequency from 150MHz to 144MHz which allows meeting
the full range of CAN bitrates.
Fixes: #60811
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
adds dts support for general purpose timer to accomodate timer driver
bringup on aglex and agilex5
Signed-off-by: Balsundar Ponnusamy <balsundar.ponnusamy@intel.com>
We use ZTEST_DMEM and ZTEST_BMEM for running tests with memory shared
between userspace and kernelspace. This ought to be documented.
Document ZTEST_DMEM and ZTEST_BMEM.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
The command did no longer set the user specified data if the user
specified more than 1 AD field.
We were using the return value of ad_init() to set the number
of AD fields. This did not take into account the number of
existing data fields. By chance this usually returned 1.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
In case a TCP connection should be established with a specific source
IP address (e.g., by calling bind() prior to connect() on the socket),
we have to actually place the address in the outgoing packet.
Signed-off-by: Tobias Frauenschläger <t.frauenschlaeger@me.com>
To prevent failure stopping a ticker node after starting it within the
same ticker_job execution (queued operations), defer the stopping until
after start. This will sequence the operations correctly and prevent
failures.
Signed-off-by: Morten Priess <mtpr@oticon.com>
For config CONFIG_BT_CTLR_CONN_ISO_RELIABILITY_POLICY, set
CIG_Sync_Delay fixed as high as possible, and calculate FT by iteration.
This favors utilizing as much as possible of the Max_Transport_latency,
and spreads out payloads over multiple CIS events (if necessary).
Add exit with cleanup as ll_cig_parameters_commit may fail after
creating new CIG/CIS instances.
Fixes issue #59605.
Fixes EBQ test HCI/CIS/BI-12-C.
Signed-off-by: Morten Priess <mtpr@oticon.com>
When CONFIG_KERNEL_DIRECT_MAP enabled, the region to be mapped
or unmapped can be outside of the virtual memory space, wholly
within it, or overlap partially. Additional processing is
needed to make sure we only manipulate the bits within
the bitmap, in other words, only the pages represented by
the bitmap.
Fixes#59549
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Check the packet lenght in flash_write operation beforeSigned-off-by
copying it to an internal buffer.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Implement the sys_poweroff hook for all ESP32 SoCs based on the previous
SOFT_OFF implementation.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Since bb590b5b6e, which enforces a more consistent ordering of
initialisation for devices, the ECIA initialisation was happening after
GPIO initialisation. This caused interrupts to stop working on GPIO
input.
This patch fixes that by increasing the default GPIO initialisation
priority, so that it happens after ECIA.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Since bb590b5b6e, which enforces a more consistent ordering of
initialisation for devices, the SOC initialisation was happening after
GPIO initialisation. This caused interrupts to stop working on GPIO
input.
This patch fixes that by increasing the default GPIO initialisation
priority, so that it happens after SOC.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
In case CAN-FD mode is not enabled the mcux flexcan driver supports
CAN_MODE_3_SAMPLES.
This has been removed inadvertently while adding can-fd support.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Convert the ISO-TP SF length check in send_sf() from __ASSERT() to a
runtime check.
Fixes: #61501
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This follows the same convention that has already been adopted by Intel
Alder Lake and Raptor Lake boards.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of link to a list of Alder Lake N products use a link to a
design document: Intel Processor and Intel Core i3 N-Series datasheet.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
