Fixes a stray ifdef which causes a build failure if the automatic
UDP start Kconfig is not enabled.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This allows for further (out of tree) customisation of the boot
banner version string when devices boot.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
The RT595 EVK needs the ROM to toggle the reset pin of the external
flash chip during a warm reset, in order to make sure the flash
is in a valid state. Add a write to the one time programmable shadow
registers when CONFIG_REBOOT=y in order to make sure the ROM will toggle
this pin.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for processing the Fault Status Registers and recoverable
data abort for Armv8-R AArch32.
Based on Arm Architecture Reference Manual Supplement Armv8, for the
Armv8-R AArch32 architecture profile (ARM DDI 0568).
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
These files have been moved in:
e6885a4515 lib: crc: move from lib/os to lib/crc
Adjust the path to the new location.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The prototype of `nrf_802154_energy_detected` callout has changed.
This commit adjusts to this change.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Use the symbol iface_ctx in place of ictx. This was
introduced seemingly by mistake in PR #61510
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
A devicetree compatible "zephyr,memory-region" was introduced in commit
18ffcdcf74 to generate linker script
memory regions from devicetree. It was enabled on arm and riscv
architectures only; extend that support to x86.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
This enables the power management for Intel ISH. It supports D0i1,
D0i2, D0i3 power saving modes for ISH.
Signed-off-by: Leifu Zhao <leifu.zhao@intel.com>
Due to source data pointer having no alignment constraint,
extra care needs to be taken when reading source data
as dword
Signed-off-by: Tomislav Milkovic <tomislav.milkovic95@gmail.com>
This adds support for the max1125x (max11254, max11254)
family of spi adc devices.
Signed-off-by: Mustafa Abdullah Kus <mustafa.kus@sparsetechnology.com>
When using the hardware map and testing on device, print out the name of
the dut (from the hardware map) on the script and report it in the json
output as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add myself (decsny) as collabotor to SD subsystem to help
to maintain the eMMC support which I added to Zephyr last year.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
When calling `bt_iso_chan_disconnect()` while the channel is
connecting, the host should simply use HCI Disconnect.
Note: For the peripheral it is not allowed to call HCI Disconnect
on a CIS after it has accepted the CIS request, but before it has
received the CIS established event. The implementation in this
commit does not fix this case. In that case the controller will
return an error code.
Also, this commit does not handle the events following the
HCI Disconnect correctly.
In this particular case, two events are raised by the controller.
See Core_v5.4, Vol 6, Part D, Figure 6.51.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Ensure the driver enables the LTE radio during init unless boot
in airplane mode is specified.
To ensure the settings applied during init are used, the LTE radio
is turned off during config.
Fix issue where PDP and GPRS connection config could have a mismatched APN.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
NET_TEST is the approprite config for networking tests that do not
require a network device. This has the same effect of disabling
NET_SLIP_TAP, but also disables other network devices. This is required
to disable e1000 Ethernet driver on the qemu_cortex_a53 board.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
PCI devices are have some differences to regular nodes:
* node name specifies device/function e.g. "pcie@1,0"
* register address has a different meaning
* zero-sized register is allowed
This improves alignment with Linux DT for PCI devices
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
The default stack size is too small on 64bit.
Some standard shell commands cause stack overflow
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Enable qemu_cortex_a53 networking using the Intel e1000 Ethernet driver.
This board only supports a single UART, so subsystems like logging and
shell would need to be disabled to use SLIP, therefore QEMU Ethernet is
used as the default instead.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Binding like "arm,gic" call these flags "flags" whereas binding like
"intel,ioapic" call them "sense". Allow either to work
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
The interrupt-map was missing the priority field.
This causes a build failure when trying to use it.
The lines are split to fit into the 100 column limit.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
The benchmark duration is in nanoseconds, and it logs the duration to
the console in seconds. The conversion is wrong for scenarios where
the execution lasts less than 100 milliseconds. Fix that by adding
leading zeros while printing duration.
Signed-off-by: Jilay Pandya <jilay.pandya@zeiss.com>
This commit adds a new sample to zbus that shows how to implement a
confirmed channel. Developers commonly asked about similar features on
zbus discord channel and RFC (in the past). Adding this sample, we can
show developers how to solve their needs (confirmed channels) without
zbus changes.
Signed-off-by: Rodrigo Peixoto <rodrigopex@gmail.com>
Bluetooth HCI drivers, Bluetooth services and the Bluetooth shell can be
considered part of the Host. Move the paths to the Host entry so that
the "Bluetooth Host" label is applied to PRs that change files in those
paths.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
