Update docs for boards ubx_evkninab3_nrf52840 and ubx_evkninab4_nrf52833
to use DEVICE_DT_GET as we phase out "label" usage and thus the
device_get_binding() reference wouldn't work.
Signed-off-by: Kumar Gala <galak@kernel.org>
When doing a split build and test with coverage enabled, (i.e.
`twister --coverage --build-only` followed by `twister --coverage
--test-only`), Twister attempts to run coverage reports immediately
after building, which fails because tests haven't actually run yet
and causes several error messages to print in to the log.
This change causes twister to skip the call to `run_coverage()` if
`--build-only` is set and print an info message. This suppresses the
error messages from the coverage report tool complaining about missing
coverage files, but still instruments the built code for coverage data
collection. When twister is invoked again, but with `--test-only`
instead, the coverage files will be emitted and the reports
successfully generated.
#### Testing
I ran...
```
$ zephyr/scripts/twister -T zephyr/tests/lib/cmsis_dsp/basicmath/
--coverage -p native_posix --build-only
$ zephyr/scripts/twister -T zephyr/tests/lib/cmsis_dsp/basicmath/
--coverage -p native_posix --test-only
```
... followed by a combined build and test ...
```
$ zephyr/scripts/twister -T zephyr/tests/lib/cmsis_dsp/basicmath/
--coverage -p native_posix
```
... as a control and diffed the HTML coverage reports, which were
identical other than a timestamp.
Signed-off-by: Tristan Honscheid <honscheid@google.com>
Add system clock control device (sysclk), so that the drivers can turn
on/off its clock through the clock control API.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
AST10x0 series SOCs provide the clock controller through the syscon
hardware block. The current driver supports the clock gating capability
for the hardware IPs embedded in the SOC. Each clock source has a
clock ID that can simply map to a bit in syscon registers CLK_STOP_CTRL0
(group 0) or CLK_STOP_CTRL1 (group 1). There are some clock sources
that don't have associated clock gating control, which are always on,
are grouped to into group 2.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Add binding for Aspeed AST10x0 clock driver. The clocks can be turned
on or off through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
For intel adsp platforms we have a common multiprocessing.c file and
then another multiprocessing.c for ace and multiprocessing_cavs.c for
cavs. Rename the cavs specific implementation to follow the convention.
There is not need to "cavs" suffix since the file is already inside its
specific directory.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Inside the common directory there were files that are CAVS specific and
are not used by ACE_V1X. Lets create a subdir called cavs inside the
common to put files that are common for only cavs plaftorms.
Note that there are still remaining code that in the common folder that
are using cavs namespace like "cavs_ipc_*" that may need some additional
work.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This is a follow-up to commit 63d6cfd654.
Revert unwanted PWM_NRFX_CH_POLARITY_MASK to PWM_NRFX_CH_COMPARE_MASK
replacement that was accidentally done in the above commit.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The stm32f303x8 SoC is not equipped with spi2 and spi3 peripherals.
Exclude them from the SoC-level devicetree.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
Fix redundant node rx reservation when receiving Periodic
Advertising Sync chain PDUs. Only the reception of first
pdu in chain, AUX_SYNC_IND PDU, needs extra node rx
reservation to be allocated for generation of incomplete
data status in case of incomplete reception of chain PDUs.
Co-authored-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This add a removes the SPI config
for the stm32H735 and stm32H7b3 disco boards
when testing the octoSPI.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit enables the octo SPI peripheral to the flash-nor
on the target board stm32h7b3i_dk from STMicroelectronics.
The octospi1 is connected to the NOR- octo-flash through
the OSPI IO Manager.
Note that JESD16 requires 9 dwords for the sdfp table.
The NOR octoflash is MX25LM51245 or compatible.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the octospi nodes to the stm32h7A3 and
and h7B0/h7B3 devices.
Note that RM0455 gives a size of 1kB.
The definition of the octospi clock source for both intances
is given by the DTS node. The selected value for
the alternate clock control is the PLL1_Q.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit enables the octo SPI peripheral to the flash-nor
on the target board stm32h735g_disco from STMicroelectronics.
The octospi1 is connected to the NOR- octo-flash through
the OSPI IO Manager.
Note that JESD16 requires 9 dwords for the sdfp table.
The NOR octoflash is MX25LM51245 or compatible.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the octospi nodes to the stm32h723/h725
and h730/h733/h735 devices.
Note that RM0468 gives a size of 1kB.
The definition of the octospi clock source for both intances
is given by the DTS node. The selected value for
the alternate clock control is the PLL1_Q.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
With the introduction of the OSPI NOR flash controller
the stm32H7 serie requires the HAL MDMA in anycase.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fix hang on chain PDU allocation by replacing K_FOREVER use
by a timeout. Hang occurs when configured number of
advertising data buffers is low.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add the ssd16xx_read_ram() function that can be used to read the raw
contents of the two display RAM in the controller. This function is
similar to display_read(), but lets the caller specify the RAM to
operate on. The intention is that this can be used to read out the
contents of the old frame buffer after a partial refresh that
automatically swaps the black/red buffers.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Read operations only work on SPI controllers that support half
duplex. To enable read operations, set the device mode to half duplex
by adding the following to the device's DTB node:
duplex = <SPI_HALF_DUPLEX>;
If read requests will fail with -ENOTSUP if the device isn't in half
duplex mode.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The UC8179 supports automatic power management where the DC-DC is
enabled automatically. This is not supported on the UC8176. Explicitly
call PON/DRF/POF from uc81xx_update_display instead. This ensures that
the DC-DC is only enabled while actually updating the display for all
supported chips.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The CDI register in UC8176 and UC8179 have different layouts. Add a
helper function to the quirks structure to handle CDI updates.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The UC8176 and UC8179 chips that exist in tree have subtly different
register layouts. Use separate compatible strings for these chips and
a quirks structure that describe device-specific behavior.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The GD7965 driver is really just a vendor name for the UltraChip
UC8179. Rename the driver to UC81xx since there are other chips in the
family (e.g., the UC8176) with an almost identical register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Some Series were calculating the pll output frequency from an
clock source index instead of the clock source frequency.
This commit resolves this issue for l0, l1.
get_pllout_frequency() is only used for PLLCLK, therefore remove it.
F2, F4, and F7 have several pll dividers and might decide to implement
these as clock sources won't need PLLCLK.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
We already have riscv_clic.h and riscv_plic.h, no need to have the same
declarations in soc_common.h as well.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
If we're disabling certain features and instead providing function stubs,
it doesn't make sense to use macros for those routines that return values
that the user may check unless we want to provide them with vague errors
like:
src/coap-server.c:101:55: error: expected expression before ';' token
101 | ret = net_ipv6_mld_join(iface, &mcast_addr.sin6_addr);
When a function we're mocking up returns a value, use a static inline
stub.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
Now that PWM drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Typically the Kconfig.defconfig* will blindly enable a
sensor and not respect the devicetree state of the PWM.
Additionally we can get problems with prj.conf/defconfig
getting incorrectly overridden.
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that PWM drivers are enabled based on devicetree we can remove
any cases of them getting enabled by *defconfig and proj.conf files.
Signed-off-by: Kumar Gala <galak@kernel.org>
