The z_interrupt_stacks was declared extern in the kernel internal
header file using the same macro which defines the same stack
array but with an added "extern" in front. This macro adds
alignment and section attribute which are actually not the same
as the actual stack array defined in kernel/init.c. The section
name used in the section attribute contains the file name where
the stack array is defined or extern declared. So the same
symbol, in this case z_interrupt_stacks, has different
attributes in two places, and GCC 11 starts to complain about
this. So use the newly introduced macro to extern declare
the stack array without adding/replacing any symbol attributes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
A stack can already be declared extern via K_KERNEL_STACK_EXTERN().
This adds similar macros for stack arrays.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Moves Z_KERNEL_STACK_LEN() higher in the header file so it is
near the other stack size calculation macros. Also, it was
actually declared after it is first used in the header.
So this seems a logical move.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This changes the type casting of the incoming addresses to
the bit ops from uint32_t* to uint8_t*. This avoids compilers
and static analyzers complaining about the incoming out of
bound access if incoming argument is an array smaller than
4 bytes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Added bt_mesh_msg_send() which can be used by the application to
directly send model layer messages without local instantiation of
related models. Also added bt_mesh_msg_cb_set() which allows the
application to recieve mesh model layer messages without local
instantiation of related models.
Added bt_mesh_has_addr() which returns a bool. For unicast addresses,
this returns whether or not bt_mesh_elem_find() was successfull. If the
above mentioned bt_mesh_msg_cb_set() has been used by the application to
set a message callback, this returns true so that the stack attempts to
push every model message up to the application via the callback. If no
callback has been set, group addresses are searched to see if the stack
should pass the message up the stack to an instantiated model.
These changes allow applications that do not or can not instantiate
models to interface with models in a mesh network. This is applicable to
applications which act as a Bluetooth mesh gateway, sniffer, debugger,
network monitoring, non-mesh relay/extender, etc.
In app_keys.c friend.c net.c bt_mesh_elem_find() is used only to
determine the existance of an address. The full return value of
bt_mesh_elem_find() is unecessary and so was replaced by the above
mentioned bt_mesh_has_addr() function in these instances.
Simplified bt_mesh_elem_find() by removing the search through group
address. Since the above mentioned bt_mesh_has_addr() function handles
instances where group addresses must be searched, it was no longer
necessary to preform this search in this function.
Signed-off-by: Bud Wandinger <bud@budkoembedded.ca>
Add support for power management and the shutdown mode for bq274xx fuel
gauge sensor. This now allows boards that have any kind of low power
mode to turn on or off the sensor.
Tested on a Company's custom board with bq27421 sensor on it.
Signed-off-by: Luka Lopotar <luka.lopotar@greyp.com>
For setting the APP_KEY, "mib_req.Param.AppKey" field should be used.
Fix it!
Fixes: #36540
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The flag source_periph seems to be incorrectly set in dma_stm32.
In case the transfer direction is from periph to mem, then the
stream->source_periph is 1 (true) else it is false.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Based on the new bindings for the stm32 dma feature,
the overlay for enabling the dmamux on spi client is modified.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Based on the new bindings for the stm32 dma feature,
the overlay for enabling the dma on uart client is modified.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The stm32l47r soc has a dma of type dma-v2, so the cells have
only 3 elements,. This adpat for the quadspi periph.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
All the macro for dma-cells are now in the
include/drivers/dma/dma_stm32.h header file.
So the include/dt-bindings/dma/stm32_dma.h is no more
useful and removed from #include.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The macro to set the element of the dma-cells for each peripheral
are defined in the dma_stm32 header file
and used in the periph driver (as dma client)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Each stm32 dma can be of V1 or V2 or V2bis type. Each type
has a dma-cell with specific nb of element. The feature and slot
properties are not required depending on the stm32 family.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This will define a new bindings for any stm32 dma feature
Depending on the soc family, the DMA is of V1 or V2 or Vbis type
And give a factored definition for feature
The difference is on the dma-cell structure.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This is the dma V2bis which is particular DMA V2 instance for
stm32F1 and STM32L1 soc series. This DMA does not use the dma slot
Otherwise it is similar to version V2.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add missing eSPI driver interface under peripheral list.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Co-authored-by: Gerard Marull-Paretas <gerard@teslabs.com>
This provides a command line interface to query and modify
bridge instances, similar to Linux's brctl utility.
It can be used to inspect an application's bridge usage,
or manage a bridge of its own in a generic way.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
This is accomplished with 3 fake ethernet interfaces hooked to a
common bridge, simulating incoming packets and controlling each
interface's transmission product.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
This adds the ability to create Ethernet bridges for connecting
separate Ethernet segments together to appear as a single
Ethernet network.
This mimics the Linux functionality of the same name.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Implement a clock control driver for Microchip MEC172x handling
configuring the 32 KHz input sources for the PLL and peripheral-32k
clock domains. MEC172x differs from MEC152x. MEC152x had one 32K source
for both PLL and peripherals. MEC172x allows the two domains to use
independent 32 KHz sources. Device tree updated to provide addresses
of hardware used by the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add project groups for enabling/disabling projects with group-filter.
Example usage:
west init -m https://github.com/zephyrproject-rtos/zephyr.git --mr main
west update --group-filter=-hal -o=--depth=1 -n
Fixes issue #36324.
Signed-off-by: Artem Panfilov <artemp@synopsys.com>
Some of the shell tests need a devicetree "fixed-partition" and
"storage_partition" for the settings partition support. Not all
boards support this, so filter the tests on the devicetree having
this.
Fixes#37115
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Logo was accidentally deleted as part of some docs cleanup. Add it back
with a new name making it more explicit that it belongs to the readme.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
cc13x2_cc26x2 had its own power policy that was implementing the same
logic available in the default residency policy. Also, this policy was
unnecessarily setting up a timeout to wakeup the system. This is not
necessary, the power subsystem takes care of this.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The exit latency for the standby state is available in
policy/policy_residency_cc13x2_cc26x2.c. Just copying it to the state
definition in dts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Option to have continous scanning simultaneously while
advertising and multiple peripheral role is active.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Babblesim test of Bluetooth Low Energy Central role
functionality by scanning for other devices and establishing
connection to upto 62 peripherals with a strong enough
signal.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Application demonstrating Bluetooth Low Energy Central role
functionality by scanning for other devices and establishing
connection to upto 62 peripherals with a strong enough
signal.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added sample to demonstrate use of multiple identity and be
able to be connected to multiple times from same central
device.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This action will run on each PR and will post a comment if footprint of
some reference applications has changed, initially as a FYI but later it
will be enforced when footprint for example is gone beyond a certain
threshold.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Very simple script to diff between two ram or rom reports generated by
size_report. When you call call the ram_report or rom_report targets you
end up with a json file in the build directory that can be used as input
for this script.
The output shows which symbols insreased and which decreased in size and
also tracked added/remove symbols as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Prevent CONFIG_CBPRINTF_STATIC_PACKAGE_CHECK_ALIGNMENT when LOG_PRINTK.
Prevent use of assert in cbprintf header when printk is redirected
to logging. Enabling it would lead to circular header includes and
compilation failure.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Assert header is including printk header and cbprintf header
may be included by printk.h when printk is redirected to logging v2.
That creates circular includes which must be prevented by
preventing using assertion and including assert header file.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
