The NPCX clock driver was already using devicetree, just need to make a
small tweak to use DEVICE_DT_INST_DEFINE and update NPCX_CLK_CTRL_NAME
to match the label for the "nuvoton,npcx-pcc" clock controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a simple pinctrl node for the IOF registers under the GPIO
controller node to be used by the pinmux driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert esp driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop CONFIG_WIFI_ESP_NAME
option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Convert ublox-sara-r4 driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop
CONFIG_MODEM_UBLOX_SARA_R4_NAME option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This include make possible to use the arm_arch_timer on
platform such as Cortex-A9 or Cortex-R7 which has support for
ARM Global Timer.
The global timer is a 64 bit incrementing counter, memory-mapped
in the private memory region.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
In some cases we cannot know the BDF up-front, so provide a way to
look it up based on the vendor and device ID.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These have been redefined in various places - better to have them in a
single place that different users can use.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Update sample espi driver test to exercise some SAF functionality
based on the limited hardware available. Note the SAF test will
erase a section of the flash. SAF tests are enabled for the EVB only.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add ESPI SAF features to the Microchip eSPI driver as
a separate file. ESPI SAF depends upon the core eSPI
driver adding the ability to attach the system SPI
flash to the EC eSPI endpoint instead of the host
eSPI controller.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This adds X86 keyword to the kconfigs to indicate these are
for x86. The old options are still there marked as
deprecated.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The app_kernel benchmarking app has the config file for benchmarking
with floating point enabled, but it was never used. So add it
to the testcase.yaml.
Note that this also limits to run on one CPU on a SMP system as
the resulting numbers would be more consistent among runs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When exiting Stop mode, if system clock is MSI, MSI oscillator is
selected as wakeup from stop clock; otherwise HSI16 oscillator is
selected.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Provide the LoRaWAN stack with an optional callback to be
called whenever the battery level needs to be read.
In the case of callback not being provided, the LoRaWAN
stack will report 255 (battery level unavailable) as per
the LoRaWAN spec.
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
nxp_k2x.dtsi: Corrects Multipurpose Clock Generator binding
to utilize nxp,kinetis-mcg. Assign MCG to FlexTimer devices.
Enable FlexTimer clocks via System Integration Module clock
gate control registers.
Kconfig.defconfig.mk22f12: Enable default use of
CLOCK_CONTROL_MCUX_MCG when CLOCK_CONTROL is selected.
Signed-off-by: Ryan Holleran <rhollerar@gmail.com>
Include coverage support for device testing. It works by switching
capture_coverage to True (as it would meet coverage data start
pattern). Then we continue tot read coverage data until we get
coverage data end pattern. Otherwise, after receiving test result
pattern, we close serial console and do not get time to find start
coverage data pattern.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Introduce a dts board overlay on the nucleo_l053r8 board as this
board was used for testing addition of resolution setting on the
mcp9808 sensor driver.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
During the driver init, the function will set the sensor resolution
based on the driver's dts variable "resolution"
The driver's device tree has been updated to include the value
"resolution".
The default is set to the highest resolution of 0.0625C.
Moved mcp9808_reg_write from mcp9808_trigger.c to mcp9808.c
This allows resue of the same function in both the trigger and
resolution functions.
Function name changed to xxx_16bit to distinquish it from the 8
bit write function that will added.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
With addition of icount support ARC QEMU is now stable,
so we can finally enable it as default test platform.
This reverts commit 7d10b68baa.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Even though ARC QEMU has received advanced multiplication
instructions support recently the ARC QEMU in the latest
Zephyr SDK still misses them, so tinycrypt may execute
too long and reach timeout in case of execution on
slow host.
Disable tinycrypt for ARC QEMU platforms till we update
ARC QEMU in Zephyr SDK.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
In this CL, npcx_miwu_interrupt_configure is no longer responsible for
turning the interrupt off. Although the default state of WK_EN is
disabled, the users still have the chance to configure them when WK_EN
is enabled via npcx_miwu_irq_enable(). Hence, this CL also ensures that
WK_EN is disabled before configuring them.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL uses a simpler configuration approach that turns GPIO's
interrupts off instead of calling npcx_miwu_interrupt_configure
with NPCX_MIWU_MODE_DISABLED.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL moves def_lvol_io_list device-tree node from npcx7m6fb_evb.dts
to npcx7m6fb.dtsi. The benefit of it is that we needn't add
def_lvol_io_list node for each board dts file if there are no 1.8V
io-pads on the platform. If so, add them in the specific board dts file
directly.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit adds the nRF IEEE 802.15.4 Service Layer Fault Handler
to the 802154_rpmsg sample.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
This commit introduces runtime query of the HW Capabilities of
the nRF IEEE 802.15.4 Radio Driver.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
This commit brings in several latest bugfixes for the hal_nordic repo.
It also removes a Kconfig entry that these changes yield deprecated.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
