Add pinctrl dtsi file for lpcxpresso55s69 board, as well as pinctrl
groups for lpcxpresso55s69 peripherals.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pinmux settings for a second LPUART peripheral for all boards where
one is present on the SOC and pins are exposed to use the uart.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Most LEDs had 0 or 4 nanoseconds set as a period, a value that doesn't
make sense for a PWM signal driving an LED. A period of 20ms (50Hz) is a
frequently used value as it is above the flicker fusion threshold. All
STM32 based boards have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This limits non-mcuboot builds to have a maximum size of 892KB to
prevent code being placed over the top of the bootloader's flash area.
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
Rather than specify input clock for each peripheral individually, instead
specify the relevant clocks in DTS.
This will enable easier support for non-default coreclk on fe310 in a
follow-up CL.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
The autoconf.h header is not required because the definitions present in
the file are exposed using the compiler `-imacros` flag.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The board specific driver for `pinetime_devkit0` has a requirement for
`CONFIG_GPIO` that was not documented. With this fix the minimal sample
build successful.
Signed-off-by: Casper Meijn <casper@meijn.net>
Instead of selecting appropriate HAS_HW_NRF_* options for particular
nRF SoCs (and simulated nRF52 target), set their values basing on
information from devicetree.
Correct also semantics of those options so that they are set only when
a corresponding DT node is enabled. This allows using them directly in
Kconfig dependencies of Zephyr drivers for nRF peripherals. Update
appropriately these dependencies.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Prevent "unique_unit_address_if_enabled" warnings from being reported
for nRF52 Series SoCs, where certain nodes need to be enabled with
the same base addresses. These can be (depending on a given SoC):
- power@40000000 & clock@40000000
- power@40000000 & clock@40000000 & bprot@40000000
- acl@4001e000 & flash-controller@4001e000
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Prevent "unique_unit_address_if_enabled" warnings from being reported
for nRF51 Series SoCs, where certain nodes need to be enabled with
the same base addresses. These are:
- power@40000000 & clock@40000000 & mpu@40000000
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable the messaging unit for NXP i.MX8M Plus EVK boards. This is a
necessary requirement to be able to run rpmsg examples later.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Since the HCI entropy device is a software construct that is able to
provide entropy bytes by retrieving them from a Bluetooth Controller,
generalize it by moving it to the Nordic common DTS code. Additionally
move the chosen nodes from the nRF5340 DK board files to the SoC ones.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add build time optional PINCTRL support to the Microchip XEC TACH
driver shared by MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Update Microchip XEC TACH driver to support MEC172x.
Standardize device tree properties between chips.
Standardize device structure usage.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Update board device tree with LTDC node
Update board documentation - display support and RGB pinout
Update board defconfig - if display is used, then external
SDRAM must be enabled in order to fit the frame buffer in
memory
Signed-off-by: Tomislav Milkovic <tomislav.milkovic95@gmail.com>
Replace custom init code with the regulator infrastructure to enable the
Vin1 monitoring circuit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
There's no in-tree driver for the A71CH secure element, which is the
code that should be responsible to control the chip reset line.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace custom init code with the regulator infrastructure to enable the
3V3 power rail.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Boards must only enable minimal peripherals according to the porting
guidelines. USB, I2C or ADC are not in the minimal list.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Improve documentation
- Add a photo of the board
- Add hardware information from the board manual
- Fix options for build (set OPENOCD_DEFAULT_PATH to make it
valid for also windows environment)
- Improve the build instructions to make it easier to understand
Signed-off-by: Yuichiro SAGISAKA <yu.sagisaka@fujitsu.com>
When the application requests `CONFIG_FLASH`, then automatically
enable the flash driver using `CONFIG_SPI_NOR`.
Signed-off-by: Casper Meijn <casper@meijn.net>
Add backlight gpios property to mcux display driver, so that the driver
can correctly initialize the backlight gpio control.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In order for pinctrl support to be complete, RT series GPIO driver must
support pinmuxing within the driver level. RT series pinmux settings do
not correspond directly to gpio port/pin numbers, so use DTS mappings to
pinctrl nodes to select and apply pinmux settings in the gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
A follow-up to #44181, this time fixing the pyocd target parameters to
match the actual hardware on the board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The jlink executable expects a fully qualified IC name, and not just the
family. Apply to all Nordic boards.
Fixes#37294
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This update Atmel sam and sam0 ethernet gmac and mdio drivers to use
pinctrl driver and API. It updates all boards with new pinctrl groups
format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 dac driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 usb dc driver. It updates
all boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 tcc pwm driver. It updates
all boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 i2c driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 spi driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam qdec sensor driver to use pinctrl driver and API.
It update board and sample with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
