STM32Cube updates:
stm32cube: update stm32wb and its lib to version V1.12.1
stm32cube: update stm32mp1 to version V1.5.0
stm32cube: update stm32u5 to version V1.0.2
update stm32cube/common_ll
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce Pin Function Controller for Renesas R-Car family.
This first implementation support to set a given pin as gpio
or peripheral (GPSR), to set a peripheral function to a
pin (IPSR), to set pull-up, pull-down (PUEN, PUD).
In addition this driver allows to set driving capabilies(DRVCTRL).
Pins are identified thanks to the per SoC binding for
pin definition which also contains pin alternate function
parameters.
Some pins can also have driving capabilities, some have bias
capabilities.
In order to find the correct bias and drive registers pfc_r8a77951.c
describes the different registers.
Each SoCs or package will need to define getters
for these registers: pfc_rcar_get_bias_regs() and
pfc_rcar_get_drive_regs().
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Pin controller address is the same for all member of the
GEN3 SoC Series, but pinmux configuration is SoC specific.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Renesas R-Car series contains a PFC (Pin Function Controller).
This module consists of registers for selecting the function of
the multiplexed pins and controls the pull-up resistor on each pin.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Host receive thread has small default stack size.
Attempt to convert data from binany to string requires
large array. Allocation of such array on stack could
cause stack overflow.
To limit the scope of the array and avoid stack overflow
the array is changed to be static local variable in a function.
Also the array has been prepared to accept max advertising
data sieze of 1650 bytes.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Up till now the littlefs only has been supporting the flash medium in
Zephyr.
This change provides code to also use littlefs stored on the block
devices - like SD card (accessed via SPI).
When FS_LITTLEFS_BLK_DEV Kconfig option is defined, the support for
using littlefs on block devices is enabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The struct flash_area *area pointer has been renamed to void *backend
pointer.
This change is enabling further rework of the littlefs subsystem to work
with other backend devices (like block ones - i.e. SD card).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
LaTeX code generated by Sphinx causes problems when using extlinks in
references. Mitigate the problem by just using the extlink role
directly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
bt_mesh_subnet_find calls a callback for every subnet, and returns the
subnet that got a non-zero return code from the callback. As pointed out
in #41693, the callback should return a boolean, not an int.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
1. Rename DT_COMPAT_ST_BBRAM_IT8XXX2 to COMAPT_ITE_IT8XXX2_BBRAM
2. The default configuration "$( )" should be a parentheses instead
of curly brackets. The BBRAM for it8xxx2 can be driven after
correcting.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
BBRAM content should be cleared when boot from cutoff. Compare magic
number to decide whether to clear entire BBRAM.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Refactors all of the on-chip flash drivers to use a shared driver class
initialization priority configuration, CONFIG_FLASH_INIT_PRIORITY, to
allow configuring flash drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers.
Driver-specific options for SPI-based flash drivers are left intact
because they need to be initialized at a different priority than on-chip
flash drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
This commit updates the ieee802154 driver to match the current feature
set of the nRF 802.15.4 radio driver for nRF53 SoCs.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
The board_internal_sensors_init function was called erlier than the GPIO
driver was initialized. This commit fixes the issue.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Clear ADRDY before enabling ADC to ensure the subsequent
wait for ADRDY does not stop prematurely in case ADRDY
was already set.
The "ADC on-off control" sections of the following reference manuals
were consulted. That gives at least one instance per series affected
by this change, even if not every affected MCU is covered.
- RM0438 (STM32L552xx and STM32L562xx)
- RM0351 (STM32L47xxx, STM32L48xxx, STM32L49xxx and STM32L4Axxx)
- RM0434 (STM32WB55xx and STM32WB35xx)
- RM0454 (STM32G0x0)
- RM0440 (STM32G4 Series)
- RM0399 (STM32H745/755 and STM32H747/757)
- RM0433 (STM32H742, STM32H743/753 and STM32H750)
- RM0453 (STM32WL5x)
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Use a wrapper for LL_ADC_Enable that also waits for ADRDY if required
by the SoC to make sure it's properly enabled everywhere this is done.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Filter out boards without st,stm32-can compatibles enabled in their
devicetree in the stm32-specific CAN driver test.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the unused base binding for CAN bus devices (as in devices
present on a CAN bus). This binding should have been removed in
2269408572
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The board features a STM32F405RGT6 MCU.
The code is based on boards/arm/olimex_stm32_p405 and
boards/arm/olimex_stm32_h103.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
The spi node of the led_ws2812 now includes the frame format
as defined by the dts bindings spi-device.yaml
SPI_FRAME_FORMAT_TI is selected with overlay for target boards.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
the stm32 spi drivers now takes the DTS frame_format property
from the include/ drivers/spi.h
It will be possible to select the Motorola (default)
or TI from the DTS entry of the device,
when soc supports it, else a run time error is raised.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The Q variant is the same as non-Q, except the Q has SMPS built-in.
This symbol addition is to have the correct
SOC definition ("STM32H7A3XXQ")
Signed-off-by: Manojkumar Subramaniam <manoj@electrolance.com>
Add kscan0 to support tests/driver/kscan/kscan_api.
When running the tests code on it8xxx2_evb, it shows fatal
error: IRQ is enabled. We find that once polling_task() is
created and executed, the KSI interrupt will be enabled and
before we call irq_connect_dynamic(), so we switch both
function sequence.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Adds fix so that a node running with extended adveriser is able to
enable GATT proxy correctly. This fixes a corner case issue where a
device with no other ongoing message sending is unable to advertise
the GATT proxy through
bt_mesh_gatt_proxy_set(BT_MESH_FEATURE_ENABLED) .
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
- Fix some syntax errors, e.g. :c:kconfig:`...`
- Remove references to missing symbols (replaced with literals)
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a dummy driver for the `vnd,adc` compatible to allow compilation of
drivers utilising an ADC when running "build_all" tests.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
On some platforms, HPET is not wired to trigger IRQ 2.
This would make HPET non-functional if the legacy
interrupt routing bit is set in the global config
register. This adds a DTS flag so the driver won't
set the bit to enable legacy interrupt.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
