Add STM32_FOO_ENABLED and STM32_FOO_FREQ to STM32 fixed clocks:
HSI, HSE, MSI(S), CSI, LSI, LSE..
Replace STM32_LSE_CLOCK by STM32_LSE_FREQ and when possible
replace by new STM32_LSE_ENABLED when making sense.
Fix STM32_PLL3_FOO_ENABLE to STM32_PLL3_FOO_ENABLED
Additionally, add STM32_PLL_FOO_ENABLED definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
PLL3 setting should also be protected CFG_HW_RCC_SEMID.
Move semaphore unlock after we're done with PLL3.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Tweak some macros definitions so that they can be used in
IS_ENABLED utility macro.
Finality is to rework STM32 clock_control driver to a more
readable format.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove conditions around some definitions since these symbols
and the node itself are mandatory.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since we are moving to pinctrl, removing pinmux.c
from mec172x board folder and removing pinmux from dts
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add macros DT_CLOCKS_HAS_NAME and DT_CLOCKS_HAS_IDX.
These macros allow to check the presence of a specific clock name
or a specific cell at a given index in a clocks property.
Matching _INST_ macro variants are also provided.
Also add DT_NUM_CLOCKS and its _INST_ variant that counts
the number of clocks available for a given node.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of DT_PROP_HAS_NAME,
update DT_DMAS_HAS_NAME definition to reuse
this helper.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a DT_PROP_HAS_NAME which helps verifying if a given string
matches an existing value in a prop-names type property.
Also add matching DT_INST_PROP_HAS_NAME
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix#42800
Both pss->rate_ratio and port_ds->neighbor_rate_ratio are double type
but sync_receipt_time is uint64_t. If pss->rate_ratio is less than 1
or sync_receipt_time * port_ds->neighbor_rate_ratio is less than 1,
sync_receipt_time becomes 0 due to double to uint64_t cast.
Assign port_ds->neighbor_prop_delay to sync_receipt_time first to fix
this issue.
Signed-off-by: Lu Ding <lucasdinglu@gmail.com>
Current implementation checks for pulldown and
pullup. As pinmux configuration is related to PU only,
this PR checks for PU feature instead of PD.
This also fix missing PU check when PD is present.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Fix k_sem_give() from being called from Zero Latency IRQs
when the Controller is configured with BT_CTLR_ZLI=y.
Kernel features shall not be used from Zero Latency IRQs as
these IRQs cannot be locked by the kernel to maintain
context safety of the kernel objects.
Relates to commit 92e017fd70 ("Bluetooth: controller:
split: Support Zero Latency IRQs") and
commit c842eef3ae ("Bluetooth: controller: Add semaphore
to indicate free AD data buffers").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
sw_switch implementation uses two parallel groups of
PPIs connecting radio and timer tasks and events.
The groups are used interchaneably, one is set for
following radio TX/RX event while the other is in use
(enabled).
The group should be disabled by timer compare event that
starts Radio to TX/RX a PDU. The timer is responsible for
maintenance of TIFS/TMAFS. The disabled group collects
all PPIs required to maintain the TIFS/TMASF. After
the time is reached Radio is started and the group is
disabled. It will be enabled again by software radio
swich during next call.
If the group is not disabled then it will work in parallel
to other one. That causes issues in correct maintenance of
instant when radio shoudl be started for next TX/RX event
e.g. radio may be enabled to early.
In case the PHY CODED was enabled and periodic advertising
included chained PDUs, that are transmitted back-to-back,
there was missing group delay disable. The missing case was
sw_switch function called with dir_curr and dir_next set
to SW_SWITCH_TX.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The commit:
- removes usage of strnlen to make taskstat code C99 compliant;
- corrects thread name len, following update description of
CONFIG_OS_MGMT_TASKSTAT_THREAD_NAME_LEN;
- reduces duplicated code.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The commit removes usage of strnlen from echo command to make
code C99 compliant, and allow it to compile with newlib.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The help for the OS_MGMT_TASKSTAT_THREAD_NAME_LEN stated that
the config includes terminating zero, but this is not true:
when thread name is encoded with CBOR it is encoded with actual
string length and is not zero terminated.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
It depends from a content formatter is there need to put constructs
with a path level deeper than object instance. In other words with
resource- or resource-instance-level.
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
No need to start the wq every time the mbox is initialized, it must be
done once for all the instances (it is shared by all the instances).
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Since `CONFIG_BT_MESH_PB_GATT` represent to pb-gatt-srv.
We use `CONFIG_BT_MESH_PB_GATT_COMMON` to represent common.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Currently if an attempt to disable CSMA-CA in by setting an
appropriate flag in another (for example application)
CmakeLists.txt it caused lots of warnings. This fix allows
higher level CMakeLists.txt to disable CSMA-CA without
warnings.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Add the support of a rpmsg tty channel that responds to the generic
Linux rpmsg_tty driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Restructure to separate the management of the rpmsg stack
add the rpmsg client into 2 threads.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
When a Seed error occurs during the random nb generation,
the driver tries to recover and exit without providing a random data
This avoids looping endlessly on the DRDY bit of the RNG status reg
because it remains 0 in case of error.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Rename the data and metadata callbacks to _read(), for consistency
with the corresponding function calls.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
Move the instance as the first parameter of the client function calls
and callbacks, for consistency with the server implementation.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
