This commit enables the CONFIG_NPCX_HEADER option for the Google Quincy
board. This is necessary to properly support the NPCX firmware header
requirements on this platform, ensuring correct boot and firmware
updates.
Signed-off-by: Firas Sammoura <fsammoura@google.com>
Be more explicit about the need for a Virtual Machine running Linux if
running in Windows.
Also WSL2 has been out for ~5 years. Let's reduce the amount of info
on how to run it in WSL1, as probably almost nobody is using it
anymore.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Enable node drbg0 in the google_quincy device tree. This node is
required to enable the entropy upstream test.
Signed-off-by: Firas Sammoura <fsammoura@google.com>
The MIMXRT1170-EVK/EVKB has an Arduino compatible header, add device
tree nodes for the corresponding pins.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
There was a missing irq-gpios property that cause
building failure on lvgl and display samples.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
MPS4, similar to MPS3 Corstone-310, splits code between DTCM and SRAM
and thus requires similar handling.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Add MPS4 pinctrl support by referring to
`mps4/common/partition/platform_base_address.h`
from TF-M's main branch.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Add initial support for the MPS4 Corstone-320 platform, including board
and SoC definitions. This platform features a Cortex-M85 CPU with an
Ethos-U85 NPU and runs in simulation using the FVP_Corstone_SSE-320
Fixed Virtual Platform.
Signed-off-by: Sudan Landge <sudan.landge@arm.com>
Adds skeleton dtsi for u5f9 for u5g9 to inherit from
Moves the peripheral nodes into dtsi's that actually has the peripheral
and includes them for SoC's higher in the series where applicable.
signed-off-by: Harris Tomy <harristomy@gmail.com>
Some of these are allegedly ESLOV connectors and have an extra
identification pin, but there's adapters on the market to use them with
qwiic modules, let's label them so they can be used with other
zephyr_i2c shields.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
These boards have a JST SH I2C connector, add the zephyr_i2c label so
they can be used with shields made for those modules.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
These are equivalent and there's adapters on the market, having a single
label allows using it shields with any other board with connectorized
i2c busses.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Change the two current instances of stemma_qt_i2c to zephyr_i2c, using
an unified label allows using this in shields.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Rename the board name to `scobc-a1`, and update the board's full name
to `SC-OBC Module A1`. And update the output of the `Hello World`
sample to match the latest Zephyr version.
Then, The supported feature section was replaced with a hw-directive
block.
Signed-off-by: Takuya Sasaki <takuya.sasaki@spacecubics.com>
In the EM (Engineering Model), the board was referred to as
"Space Cubics Module 1". Starting with the FM (Flight Model) release,
we are officially renaming it to:
`SC-OBC Module A1`
Accordingly, the board name is updated from `scobc_module1` to
`scobc_a1`.
Signed-off-by: Takuya Sasaki <takuya.sasaki@spacecubics.com>
The arduino Uno R4 has only ioport1 enabled in the dts. The arduino
header however uses ioport0,1,3 [minima variant] and ioport 0,1,3,4
[wifi variant]. This causes a build failure for some of the pins.
This change makes sure than an application can use any arduino pins.
Signed-off-by: Loic Domaigne <tech@domaigne.com>
Add `virtio-mmio` nodes that are retrieved from qemu internal
devicetree dump, to dts.
Also, enable the virtio-rng device on the command line.
Note: Ideally, it would be possible to dynamically generate the
command line by looking at the devicetree state,
but this PR is a fixed implementation to simplify it.
This will be addressed separately.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
When running naive sim builds using clang, respect user passed
SYSROOT_DIR values. Additionally, allow overriding the archive tool
when calling Make for the native simulator.
Add the sysroot (if available) to the native_simulator target and
TOOLCHAIN_C_FLAGS and TOOLCHAIN_LD_FLAGS. Additionally pass CMAKE_AR
to NSI_AR.
Signed-off-by: Yuval Peress <peress@google.com>
This shield includes a drv8426 stepper driver and a mcp4726 dac for
current control. Note that the micro-step pins are controlled by
physical switches and are thus not available in Zephyr.
Signed-off-by: Jan Behrens <jan.behrens@navimatix.de>
This shield includes a ti drv8424 stepper driver that is controlled
via gpio. Some of these pins are only available via the tca9538a gpio
expander on the shield.
Signed-off-by: Jan Behrens <jan.behrens@navimatix.de>
