When CONFIG_PM=y, the IRQ function also needs to be stored, something
the "generic" uart_device_config cannot support. This uses the config
irq_config_func field to store the function in all situations, thus
removing unnecessary logic and finally dropping uart_device_config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of using "generic" uart_device_config fields, store the right
pointer to avoid unnecessary casts. This change makes code simpler and
more idiomatic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Follows #41918.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
This is a follow-up to commit 11bbdb030d.
When RX is automatically disabled because all provided RX buffers have
been filled up, the rx_enabled flag needs to be cleared, otherwise it
will be impossible to enable RX again.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
added UART interrupts driver for Raspberry Pi Pico board
moved baudrate from config to data structure
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
if peripheral clock is not configured, uart init API function returns 0,
so we need to check the return value of this function
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
A common pattern here was to take the work item as the subfield of a
containing object. But the contained field is not a k_work, it's a
k_work_delayable.
Things were working only because the work field was first, so the
pointers had the same value. Do things right and fix things to
produce correct code if/when that field ever moves within delayable.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
UARTE does not support RO TX buffers. Added cache buffer to the
driver which is used when provided buffer is not from RAM.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Gives more explanation on uart_stm32_err_check function.
On stm32 F4X, F1X, and F2X, when clearing the usart Error Flag
(PE, ORE, FE, NE), the LL Clear function applies a software sequence
which reads the usart SR then the usart DR.
Consequently the RXNE flag is affected (cleared) by the
uart_stm32_err_check function call.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch adds fixes to the api so that it behaves as expected.
1 - The irq_tx_ready now only returns true if the tx interrupt is
enabled.
2 - The irq_tx_complete now functions as expected and returns true
only once all characters have been transmitted
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
HAL call function used to retrieve the configured baudrate
returns the real calculated value, which might not be exactly as
the configured. For baudrate of 115200, HAL api
returns 115201, which then causes uart_basic_api test
to fail. Instead of returning the calculated baudrate value,
returns the configured one.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This corrects the following:
1. The priority of type cast is lower than member access. So don't need
the redundant parentheses.
2. The macro should be added to the parentheses.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
The current driver doesn't handle the LBD flag, this leads
uart_stm32_err_check to return always true if a Line Break
is detected.
This PR adds Line Break Detection and the related flag clearing,
F0 series it's excluded from the changes.
Fixes zephyrproject-rtos#41339
Signed-off-by: Andrea Campanella <andrea.campanella@helvar.com>
Current gpio and uart initialization level is set to
PRE_KERNEL_2, which won't let uart_console subsystem
to init its hook properly as it has same level.
Prioritize uart and gpio so that the console hooks
are properly initialized.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Update the Kconfig configuration items used to determine if the current
target is based on the Zynq-7000 SoC family as part of the re-organi-
zation of the Zynq-7000 SoC configuration data.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@Weidmueller.com>
After #41918, DEV_CFG removal triggered discard qualifer warning
during build. As uart_hal functions don't required const qualifier
and uart_context_hal_t has modified data, this PR moves hal instace
to data struct instead of config struct.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Some drivers explicitely casted data/config from void * to the
corresponding type. However, this is unnecessary and, in many drivers it
has been misused to drop const qualifier (refer to previous commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace all get_dev_data()/get_dev_config() accessor utilities with
dev->data and dev->config.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Stop using redundant DEV_DATA/DEV_CFG macros and use dev->data and
dev->config instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This fixes both TX ready and completed uart
calls to meet valid condition.
Closes#41526Closes#41624
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
For functions returning nothing, there is no need to document
with @return, as Doxgen complains about "documented empty
return type of ...".
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
An additional devicetree poperty `single-wire` is added
to uart and usart bindings of stm32. The driver checks this value
during initialization and enables the single wire mode when set.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
Use pm_state_cpu_get_all to obtain CPU states instead of using extra ROM
duplicating existing information already holded by the PM subsystem.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
ESP32 uart_poll_in should return 0 on success and not
the total amount of data read.
This also adds a check in fifo_fill call to
avoid negative values, otherwise it would send garbage
to uart
Closes#41352
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
The PINCTRL_DT_(INST_)DEFINE macros already defined the trailing ;,
making its usage inconsistent with other macros such as
DEVICE_DT_DEFINE.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Driver was not behaving according to API description and
was not returning -EBUSY when uart_rx_enable() was called
on already enabled receiver.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Fix pin disconnection when COFNIG_PINCTRL=n, so that less power is used
in suspended state. This seems to be a copy-paste kind of bug, since
when both resuming and suspending the same configuration was applied.
Fixes: 5567d7ae07 ("drivers: serial: nrfx_uart: add support for
pinctrl")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Modifying configuration to enable with gd32vf103
- Add usart definition to devicetree.
- Define USART_STAT as alias of USART_STAT0 if not defined it.
- Enable USART if SOC_SERIES_RISCV_GIGADEVICE_GD32VF103.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
In this commit, the driver sets the PM constraint to prevent the system
from entering the suspend state for a CONFIG_UART_CONSOLE_INPUT_EXPIRED
period when data come in. The constraint releases after the
CONFIG_UART_CONSOLE_INPUT_EXPIRED time expires, .
With this change, the PM policy doesn't have to check the timestamp
by calling npcx_power_console_is_in_use() explictly. So the related
npcx_power_console_is_in_use*() functions can be removed.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Some tests like:
tests/kernel/sched/metairq/kernel.scheduler.metairq
tests/kernel/profiling/profiling_api/kernel.common.profiling
tests/kernel/sched/schedule_api/kernel.scheduler
tests/kernel/sched/schedule_api/kernel.scheduler.multiq
tests/kernel/profiling/profiling_api/kernel.common.profiling
tests/kernel/workq/work_queue/kernel.workqueue
don't support that the current thread change when writing a message with
printk (which uses poll_out). So, we remove the call to k_yield which is
useful only for optimizing cpu usage by forcing a thread change if the
usart send stack is full.
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
GD32 HAL use two USART status register name, USART_STAT and USART_STAT0.
This add a redefine to make USART_STAT as defaut name.
Signed-off-by: HaiLong Yang <cameledyang@pm.me>
A dead lock could happen if 2 threads with differents priorities use
poll_out. In fact, the lock data->tx_lock could be lock by a thread with
lower priority and then a thread with higher priority can't take the
lock. There was a race condition here:
/* Wait for TXE flag to be raised */
while (1) {
if (atomic_cas(&data->tx_lock, 0, 1)) {
/* !!!!!!!! RACE CONDITION !!!!!!!!!!!!!!
if (LL_USART_IsActiveFlag_TXE(UartInstance)) {
break;
}
atomic_set(&data->tx_lock, 0);
}
}
To fix race condition, the interrupts are locked in poll_out.
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
This commit adds Xen consoleio serial driver. It is needed to receive
kernel messages from Zephyr in case it runs as Xen privileged domain
(Dom0). There is no console ring buffer for such domain, so regular
uart_hvc_xen driver can not be used (privileged domain input/output
are possible only through consoleio interface).
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
This commit adds support of interrupt-driven API for UART-like Xen PV
console driver. It is implemented via Xen event channels. It allows to
send and receive data by chunks (not single symbols) and without
polling.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
Rename the PM_STATE_DT_ITEMS_LIST macro to PM_STATE_LIST_FROM_DT_CPU to
make its purpose more clear. Similar naming scheme is found e.g. in the
GPIO API.
Associated internal macros and docstrings have been adjusted, too.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
