Those options are not being used anywhere, so remove them and avoid some
confusion.
Change-Id: Ia3767dbd2432851dfae4b1e996f02ed1b2450505
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bluetooth controller implementation requires the low power
oscillator for radio time space scheduling and as sleep
clock; the high frequency oscillator as the active clock.
For Nordic Semiconductor's nRF5 Series SoC's select the
NRF Clock peripheral when BLUETOOTH_CONTROLLER is selected
in Kconfig build.
Jira: ZEP-897
Change-id: I6f99e90b3485e757be61e91c749e485dd0cfdaba
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
The driver performs one shot PHY setup. There is no support for PHY
disconnect, reconnect or configuration change. The PHY setup,
implement via KSDK contains polled code that can block the
initialization thread for a few seconds.
There is no statistics collection for either normal operation or error
behaviour.
Origin: Original
Change-Id: Ia0f2e89a61348ed949976070353e823c178fcb24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Move SRAM_BASE_ADDRESS and FLASH_BASE_ADDRESS to Kconfig.soc since
it will most likely be the same values for all STM32 socs.
Change-Id: I682dc441e34155a19a4f90757707008ef299e9d4
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Quoting the product specification this device contains an "ARM
Cortex-M4 processor with floating-point unit" or, as this would
more normally be expressed an ARM Cortex-M4F.
Update Kconfig accordingly.
Change-Id: I5bd6f17724d0d4aa9aaab9961f12d4e8502c38a5
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Provide a random driver wrapped around the KSDK RNGA driver.
Origin: Original
Change-Id: I43feeb37d8d5173c7b95af8e80434fb7dc77a83e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Watchdog timer is enabled after the board reset. It is not used by Zephyr OS,
and having it enabled causes system resets during CPU-intensive operations.
Change-Id: If5583dbd2d2fb2206274467c523d6b5d147f1fbe
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Define symbolic constants for watchdog timer registers.
Provides the necessary interface to configure or disable
the watchdog timer.
Change-Id: I80002a843361569fdd78b725fc3f68e65195d02e
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
There is a total of 39 IRQs defined at nrf52/soc_irq.h.
Change-Id: Id478fb15a07cfdecaa6cc136730d20017b8752c5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Add a shim layer around the ksdk I2C driver to adapt it to the Zephyr
I2C interface. Currently only supports master mode.
Jira: ZEP-717
Change-Id: I704b8c38e22e456bb9fa4325682b2a354a27a7ba
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Since nrf.h abstracts the differences between the nRF51 and nRF52
architectures and chooses the right headers to include, it is
safer to use that instead of directly including the soc-specific
headers.
Jira: ZEP-702
Change-Id: I0e1758ede48f3422a41d226b0eab008e4ba2c77c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The ksdk provides a clock driver, fsl_clock.c, for the K64F and an
example usage of that driver, clock_config.c, for the Freedom board.
See ext/hal/ksdk/devices/MK64F12/
Leverage parts of clock_config.c to configure the clocks (specifically,
the sequence in BOARD_BootClockRUN()), but use the new Kconfig options
to set up the configuration structure. This will allow support for new
boards that may have a different external oscillator frequency or type.
Jira: ZEP-715
Change-Id: I3f0c75e6236f57600cd8b7f06f4482b13026fc10
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Many Kinetis SoCs contain an Oscillator (OSC) module and a Multipurpose
Clock Generator (MCG) module to configure clocks. Adding options to
configure these modules for PLL operation with different external
oscillator frequencies, which can vary across boards. More options may
be added later to support other clocking modes such as FLL.
Jira: ZEP-715
Change-Id: Ia121cc5b464d7e681883507bd756d331a8abd6ef
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The K64F SoC initialization previously used macros and structs
custom-defined in Zephyr in order to access peripheral registers.
Refactored it to use CMSIS-style register accesses from the ksdk
instead.
Change-Id: I80975c62de07ec95cf830e99cd5b0abb9623acd0
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds Kconfig options CPU_HAS_FPU, FLOAT and FP_SHARING for the arm
architecture.
NOTE: All SOCs in the MK64F12 family have an FPU so that makes it a
convenient location to enable the hidden CPU_HAS_FPU option.
Change-Id: I71771d24f20f52079314bb8db9bf8a0aa827ab41
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
at91sam3 supposed to go to Sleep mode and stop the CPU clock
(HCLK). It leads to JTAG problems. In order to be able to use
JTAG, we need to keep CPU clock on. This is achieved by
switching to Wait mode and keeping external main clock.
Since Wait mode switches off automatically Fast RC Oscillator,
but keeps external clock untouched.
Change-Id: Ife37a7691c3cbdf434e560725a71d419adafe054
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Add hidden configuration HAS_KSDK for SoCs to select if they have
support in the ksdk.
Change-Id: Ia4cd11901bc26d21a3bdfad6236d66656bb292cb
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
There was a reference to SOC_FAMILY_NRF5 which was not use by anyone
else and it seemes like it was a typo, where the right reference was
to symbol SOC_NRF5. However, the right fix is to move both sites to
use SOC_FAMILY_NRF5 *and* fix the SOC_SERIES to be only nrf52,
otherwise it causes path duplication and the build fails.
This was also causing documentation warnings that are thus killed.
Change-Id: I92e74a6158f02df43e6e857df8f1e67bcfdd9551
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
The KSDK device header files require a preprocessor macro that defines
the part number string (e.g., MK64FN1M0VMD12). Create a hidden Kconfig
option to hold the part number string, and hidden Kconfig options that
the board Kconfig will use to select the specific part number.
Change-Id: I612e785026261e425b47b5b7fae0c65b4f94b30b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Include nrf.h instead of directly using the specific header
required. This will be useful in the future when additional
Nordic ICs are supported.
JIRA: ZEP-377
Change-Id: I7a7257b0aaa5fa0a0d202322c366efbdd1d84458
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Translate CONFIG_SOC_SERIES_NRF52X to NRF52, which is the macro
expected by the Nordic MDK headers.
JIRA: ZEP-377
Change-Id: Ic846e4cddf8146ae9d96bc98d4b12311552dc4f6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Generate kernel image in Intel Hex format when building for the nRF52.
Remove the additional step from the board doc file.
Change-Id: I619496f64037c2a0ac459ae05e549e01458e0f71
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Moved setting of specific Cortex-M compiler flags in each SoC directory
unify setting them in the arch/arm/soc Makefile.
Add flags for Cortex M0, M0+, M1, M3, M4, and M7. However only
CONFIG_CPU_CORTEX_M3 and CONFIG_CPU_CORTEX_M4 are supported at this time
As part of this change converted Kbuild files for some SoCs into
Makefiles as the Makefiles would be empty otherwise.
Change-Id: Ie4e0178b141ca761ec482a610ae50e94fe58070f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a soc-cflags, soc-cxxflags, and soc-aflags as a means for
SoC specific compiler flags to be set without manipulating Kbuild
options directly.
Change-Id: I2c8f5019fb237429e59717ef96bd4251a61dc1a5
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the same Kconfig infrastructure and options for all SPI drivers.
Jira: ZEP-294
Change-Id: I7097bf3d2e1040fcec166761a9342bff707de4dd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Avoids confusion with .gitignore rules, which were inadequate to
cover all the places where these files are found. At least in
VIM, these files are now syntax highlighted correctly.
Change-Id: I23810b0ed34129320cc2760e19ed1a610afe039e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The UART console init should be done after UART init. So it can be
folded into general UART init, thus one fewer SYS_INIT().
Change-Id: Ifb18c5308dfef790325e6bff5bc7b5976fcd421e
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The clkInit() is always called so this can be inlined.
This saves 32 bytes of ROM space compared to non-inlined version.
Change-Id: I2cb6d02c0996acad16029be243f6059183938089
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The clock_init() is always called so this can be inlined.
This saves 32 bytes of ROM space compared to non-inlined version.
Change-Id: I1b95142da4c22f4b7fc7f7f6210503d90cf65cc9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This also enables GPIO on ATMEL SAM3 when GPIO is set.
Change-Id: I4125af4910d57bed98b0ee4967fb696e3f345e67
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The files soc_config.c and soc_gpio.c use errno code so they should
include errno.h.
Change-Id: I94237aa294701cc71ed17ea42eca9d8073d4ae47
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
It was not possible to add directories under an SoC family
because of the direct call to Makefile in the SoC series from the
architecture level.
While we have SoC still using the old structure, add a conditional
to still support old structure and allow Makefiles directly under
an SoC family directory.
This is useful for adding drivers and BSP files common to one family.
Change-Id: I85dc8341523b41949de91d78675153ce0baa5aac
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
With most boards there's no simple way to get access to the HCI
traffic. Simultaneously these boards only have one external UART for
the console. This patch introduces a protocol which combines both
normal logs and HCI logs over a single binary protocol sent over the
console UART.
The protocol is modeled based on the btsnoop/monitor protocols used by
BlueZ, and the first tool that's able to decode this is btmon from
BlueZ ("btmon --tty <tty>").
For platforms with two or more external UARTs it is still possible to
use CONFIG_UART_CONSOLE as long as the UART devices used are
different, however on platforms with a single external UART
UART_CONSOLE should be disabled if BLUETOOTH_DEBUG_MONITOR is enabled
(in this case printk/printf get encoded to the monitor protocol).
Origin: Original
Change-Id: I9d3997c7a06fe48e7decb212b2ac9bd8b8f9b74c
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use SoC family/series and reoganise the structure to follow new
hierarchy.
Change-Id: I8637f1487a8287a6614ce6636cd018cf342fec95
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add Kinetis SoC family and rename fsl_frdm_k64f to mk64f12.
This will allow adding new SoCs of the same family and the reuse of code
among SoCs of the family and series.
Change-Id: Iea1a663aef7ce0487f147bdd36f668bebe80deb5
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use SOC_SERIES_* for naming SoCs with similar features and architectures
with the goal of code reuse. The Series in the config variable should avoid
name collisions and clearly denote the relationships within an SoC family.
Change-Id: I7a98542f96b5d5dc3acc23782c4d45f98cceb599
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use CONFIG_SOC_FAMILY for the top level SoC family. A family
will have different SoCs or different SoC series with multiple
SoCs.
Adding the Family string to the config variable to avoid confusion
between actual SoCs and families and to prevent name collisions.
Change-Id: Ic99a2c1df7850dee3a45641027af82464dd6fadb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove those kconfig options that are SoC specific, and
should not be configurable via kconfig.
Change-Id: Ifd65097a65f80539cac073f95aadc2d8e42efb9f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There is no need to re-define CONFIG_UART_CONSOLE_ON_DEV_NAME to be
"UART_0" all over the place as its default is "UART_0" already.
So remove those duplicate defaults.
Change-Id: Ia86e26b8f90540fdbd7dcb3358d6dac352648b21
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The base address, IRQ line, chip select numbers, and clock
gating constants are static per SoC, so there is no need to
make them configurable in Kconfig.
Change-Id: I9f87ca29c28c38c42d4e4f1a3a41fa231f63ef03
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The base address and IRQ line are static per SoC, so there is no need
to make them configurable in Kconfig.
Change-Id: Ib78401ff136c29642356f5bda9d6cd3e5c98bece
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The UART port base address, IRQ line and clock frequency are static
per SoC, so there is no need to make them configurable in Kconfig.
Change-Id: Ia252958d205e0100d1b92e2a12d4c22411bc94b9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
