Convert the ft5336 to the input subsystem, fix all the config in the
repository and add the Kscan compatibility driver to the current dts
driver instances.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Switch all imxrt boards to use the systick timer by default, and only
enable the GPT timer when using low power modes. This is desirable
because the systick has a higher resolution, but the GPT can run
while the core clock is gated, making it useful for low power modes.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Document support for flexspi as flash controller on mimxrt1064_evk, and
move status=okay for internal flash to soc level dtsi
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce zephyr,keyboard-scan chosen node property to point to the
node that implements the default KSCAN device. This is similar to
the zephyr,display property.
We switch over the samples to utilize the new property instead of
kscan0 alias.
Signed-off-by: Kumar Gala <galak@kernel.org>
Replace sensor_label property in devicetree with just a sensor phandle
property. This is more generic and allows driver to use DEVICE_DT_GET
instead of device_get_binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
enable swo output for iMX RT 10xx series. SWO pinmux settings are
currently only present for the RT1060 and RT1064
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
We should avoid use of the label property in devicetrees. The
'zephyr,sdmmc-disk' compatible node has a 'label' property set
but there isn't any code utilizing this so removing the property
from any devicetrees that have it set (as well as example in docs).
Signed-off-by: Kumar Gala <galak@kernel.org>
flash controller on RT boards should be the flash device, rather than
the flexspi, as the flash device's driver implements flash APIs.
Fixes#45505
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
User switch on mimxrt series boards requires a pull up resistor
to ensure the GPIO state does not float
Fixes#45129
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable new USDHC driver for all RT10xx boards, since those will have
the SDHC driver selected by Kconfig
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add the PWM period cell to PWM driven LEDs. A value of 20 msec has been
chosen as it is the most common value used in other boards.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add backlight gpios property to mcux display driver, so that the driver
can correctly initialize the backlight gpio control.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP MIMXRT10xx/11xx EVK boards are equipped with NXP TJA1057 CAN
transceivers with a maximum bitrate of 5Mbit/s.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Enables low power clocks for mimxrt1064. This allows the soc to
transition into very low power states during idle, as most PLLs can be
disabled. Power states need to be enabled and selected at the board
level.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This enables the GPT timer for use as a hardware clock on the
MIMXRT1064. The timer will be disabled when builds use the GPT timer as
a counter, and the build will fall back to using the Cortex M systick as
a timer. This was tested using the kernel tickless test, to verify the
driver functions as expected.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for LPSPI DMA mode on RT1064, RT1060, RT1050, RT1024,
RT1020, RT1015, and RT1010 evaluation boards. Update tests to match.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename the Zephyr chosen property for specifying the default CAN bus
controller from "zephyr,can-primary" to "zephyr,canbus".
The "zephyr,can-primary" property name was selected in antipation of
adding support for redundant CAN networks, which we have yet to
add. Meanwhile, the "primary" term causes confusion for non-redundant
CAN bus configurations (and the "can" term doesn't match the name of the
Zephyr CAN bus subsystem).
The CAN in Automation (CiA) 302-6, which deals with CANopen network
redundancy, uses the terms "default interface" and "redundant
interface". If/when we add support for redundant CAN networks, the
"zephyr,canbus" chosen property can be supplemented with a
"zephyr,canbus-redundant" chosen property.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
SPI support is available on LPSPI1 and LPSPI3. Both of these require
board modifications to expose headers. LPSPI1 is used for testing, and
requires that the board have solder jumpers R278, R279, R280, and R281
bridged.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The mimxrt10xx evaluation boards that support the NXP USDHC IP
communicate unreliably with SD cards at 1.8V using the USDHC driver.
This commit temporarily disables 1.8V communication for all rt10xx
boards that currently support the USDHC driver.
Fixes#32289
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enables the dma driver on the mimxrt1064_evk board. The board
documentation is not updated because it already mentions dma driver
support.
Tested with:
- tests/drivers/dma/chan_blen_transfer
- tests/drivers/dma/chan_link_transfer
- tests/drivers/dma/loop_transfer
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the watchdog driver on the mimxrt1064_evk board. The board
documentation is not updated because it already mentions watchdog driver
support.
Tested with tests/drivers/watchdog/wdt_basic_api
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
USB devicetree nodes in Zephyr have different names,
mostly derived from the designations in data sheets.
Add zephyr_udc0 (USB device controller) nodelabel to
specific USB node to allow generic USB sample to be build.
Follow up on commit b4242a8 ("boards: add USB node aliases")
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Configures lpuart3 pinmuxes. This instance is attached to the Arduino
serial header pins and can be used for Bluetooth serial HCI with a
frdm_kw41z or other BLE controller shield.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
USB devicetree nodes in Zephyr have different names,
mostly derived from the designations in data sheets.
We also have an USB audio sample which has a kind of
experimental approach to configure audio devices, that
are not real hardware, via devicetree.
Sample itself is generic and can be run on any board with
USB device controller and isochronous endpoints support.
Add usbd0 alias to specific USB node to allow generic
USB audio sample to be build on nRF and i.MX RT boards.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Adds flash partitions and chosen nodes to the mimxrt1064_evk device tree
to support mcuboot on the internal QSPI flash. This flash is rated for
100K minimum program-erase cycles per sector, therefore this partition
configuration supports approximately 100K / (1984/64) = 3225 upgrades.
Also enables FlexSPI flash driver XIP mode support on this board to
support mcuboot.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the FlexSPI NOR flash driver, configures the FlexSPI pins, and
updates the board documentation accordingly on the mimxrt1064_evk.
Note that this SoC has two FlexSPI instances: one instance has an
in-package QSPI flash used for XIP; the other instance has a board-level
QSPI flash used for storage, not XIP. This patch enables the flash
driver on the non-XIP flash only.
Tested with:
- samples/subsys/fs/littlefs
- samples/drivers/flash_shell
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
boards: arm: Rename flexspi_qspi to flexspi_nor for mimxrt1064_evk
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the NXP FlexSPI device tree bindings to configure controller and
device properties needed for an upcoming FlexSPI flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sets the device tree chosen node for instruction tightly coupled memory
(ITCM) on all i.MX RT boards. Leverages the common Cortex-M linker
section instead of the SoC-specific one.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors nxp i.mx, kinetis, and lpc board-level device trees to use
DT_SIZE_K and DT_SIZE_M macros to define external memory sizes. This is
self documenting and easier to read.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sets the device tree chosen node for data tightly coupled memory (DTCM)
on i.mx rt boards that aren't already using DTCM as the chosen SRAM.
Leverages the common cortex-m linker section instead of the soc-specific
one.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Removes the DATA_LOCATION Kconfig symbol from the i.mx rt soc series and
refactors corresponding boards to use a device tree chosen node instead.
The external SDRAM is chosen on all boards that can support it;
otherwise the internal DTCM is chosen.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds imx rt support.
Allows n-number of can interfaces based on device-tree.
Adds a "common" irq name.
Added CAN bus pins and dts for 1060 and 1064 EVK.
Signed-off-by: Rick Talbott <rtalbott@fastmail.com>
Enables sdhc on the mimxrt1064_evk board. Configures pinmuxes and device
tree, and updates board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes dependency for I2C so that it's enabled if kscan is enabled.
This is to allow the kscan_ft5336 sample to run.
Note: LVGL has KSCAN as a dependency.
Applies to the mimxrt10{50,60,64}_evk boards.
Signed-off-by: Mark Olsson <mark@markolsson.se>
In conversion of nodelabels to match SoC docs, we missed a case in the
board dts files. However these delete-node commands are not needed as
we normally handle this via the 'status' property being disabled which
enet2 is by default in the SoC dtsi files. So we can safely just remove
the stale /delete-node/ eth1 lines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
