When compiling existing libraries that are difficult to change, these
headers simplify the library's integration. This specifically was the
agreed upon fix for trying to compile Android's CHRE as a subsystem.
Making changes to the Android repo to use the C style includes would be
very difficult and would likely take a very long time.
Signed-off-by: Yuval Peress <peress@chromium.org>
Fix some leftovers from the pm_device_state changes.
Fixes build problem introduced in
cc2f0e9c08.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This change ensures the CPU won't get an interrupt number which is
being generated.
it8xxx2 has a limitation for interrupt vector register.
CPU may read incorrect interrupt number in ISR.
The following is an example that got incorrect interrupt number:
1. Register IVECT = 0x10. (no interrupt pending/IVECT_OFFSET_WITH_IRQ)
2. Chip INT6 interrupt occurs (IVECT = 0x16) and jump to ISR.
3. Read interrupt vector register to determine interrupt number.
4. Higher priority interrupt occurs (for example: INT158, IVECT = 0xAE)
while the CPU is reading the interrupt vector register for EC INT6,
CPU may end up with an incorrect interrupt number between 0x16 and 0xAE.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Save ra to caller saved register is wrong because it might get
overwritten after another function is called, so we fix this.
Remove clear mip register operation. (it8xxx2 supports machine-mode
only, and MEIP bit of mip is read-only).
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
__LL_RCC_CALC_HCLK1_FREQ is only available for WL and WB series,
for other series __LL_RCC_CALC_HCLK_FREQ should be used.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The nRF QSPI has a configurable delay from the rising
clock signal to the actual sample point measured in
clock cycles. This commit exposes that delay as a DTS
parameter without modifying existing behavior.
Signed-off-by: Abram Early <abram.early@gmail.com>
The definition of qspi_flash_get_parameters, that implements
the mandatory get_parameters API call for the driver, was incorrectly
placed within block conditionally compiled when
CONFIG_FLASH_PAGE_LAYOUT is defined.
The commit fixes the issue that was causing compilation error
when the config has not been set.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This reverts commit a6a7a0d888.
Both application and network core define the same pins for uart0.
The pins should not be used simultaneously by both cores.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
add devicetree node for usart4 and usart5. usart4 and 5
shares the same interrupt line (14), hence both can't be enabled
at the same time.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
The Bluetooth proxy feature includes proxy client and proxy server.
In addition to the proxy pdu message used above, pb-gatt also uses
the same proxy pdu message.
Currently zephyr bluetooth mesh couples them in one file.
A file at the separation is called gatt_services.c,
which is used to contain Mesh Provisioning Service and
Mesh Proxy Service.
Another file in the separation is called proxy_msg.c,
which is used to process Proxy pdu messages.
Also according to Trond's suggestion:
Rename CONFIG_BT_MESH_PROXY to CONFIG_BT_MESH_GATT.
Create an additional promptless entry CONFIG_BT_MESH_GATT_SERVER
that selects CONFIG_BT_MESH_GATT and is selected by
CONFIG_BT_MESH_GATT_PROXY or CONFIG_BT_MESH_PB_GATT.
Create additional CONFIG_BT_MESH_PROXY used to represent
proxy feature (also include proxy client).
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
The Bluetooth proxy feature includes proxy client
and proxy server. In addition to the proxy pdu
message used above, pb-gatt also uses the same
proxy pdu message.
Currently zephyr bluetooth mesh couples them in one file.
A file at the separation is called gatt_services.c,
which is used to contain Mesh Provisioning Service and
Mesh Proxy Service.
Another file in the separation is called proxy_msg.c,
which is used to process Proxy pdu messages.
Also according to Trond's suggestion:
Rename CONFIG_BT_MESH_PROXY to CONFIG_BT_MESH_GATT.
Create an additional promptless entry CONFIG_BT_MESH_GATT_SERVER
that selects CONFIG_BT_MESH_GATT and is selected by
CONFIG_BT_MESH_GATT_PROXY or CONFIG_BT_MESH_PB_GATT.
Create additional CONFIG_BT_MESH_PROXY used to represent
proxy feature (also include proxy client).
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
The Bluetooth proxy feature includes proxy client
and proxy server. In addition to the proxy pdu
message used above, pb-gatt also uses the same
proxy pdu message.
Currently zephyr bluetooth mesh couples them in one file.
A file at the separation is called gatt_services.c,
which is used to contain Mesh Provisioning Service
and Mesh Proxy Service.
Another file in the separation is called proxy_msg.c,
which is used to process Proxy pdu messages.
Also according to Trond's suggestion:
Rename `CONFIG_BT_MESH_PROXY` to `CONFIG_BT_MESH_GATT`.
Create an additional promptless entry
`CONFIG_BT_MESH_GATT_SERVER` that selects
`CONFIG_BT_MESH_GATT` and is selected by
`CONFIG_BT_MESH_GATT_PROXY` or `CONFIG_BT_MESH_PB_GATT`.
Create additional `CONFIG_BT_MESH_PROXY` used to represent
proxy feature (also include proxy client).
see #36343
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
This commit fixes the button activity notification not working issue.
The right attribute(4) is used for the button service.
This has been tested on nucleo_wb55rg and disco_l475_iot1 platforms.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit selects LL_RCC_RNG_CLKSOURCE_CLK48 as a clock source
to rng peripheral. LL_RCC_RNG_CLKSOURCE_CLK48 is CLK48 divided by 3.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
6lowpan module can swap the original buffer with a newly allocated one
during decompression in case the decompressed header would not fit into
the original buffer. Therefore, storing the LL address offset and
restoring the pointer after decompression as it is done today is not
correct, as the new packet with decompressed IPv6 header will not
contain the LL header.
As the 6lowpan module doesn't deallocate the original buffer and
doesn't overwrite the LL header, its fine to use the original
pointers as they are.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Include the TI HDC2010, HDC2021, HDC2022 and HDC2080 temperature and
humidity sensors in the build_all test, to test the TI_HDC20XX driver.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add basic support for TI HDC20XX series (e.g. HDC2010, HDC2021, HDC2022,
HDC2080). It is able to get temperature and humidity in the default
14-bit resolution. Triggers, resolution selection, interrupt line, auto
measurement mode are currently not supported.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Activate optimizations for stm32h735g_disco which in the end
optimize the calls to ferror and fileno away.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The type used by device PM state was not changed to the recently
introduced enum type. The state is also initialized to a value distinct
from the first expected value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add Kconfig option for indicating that a given SoC contains the NXP
Kinetis Reset Control Module (RCM).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Thos tests/samples are used to build any PR onl all available boards to
verify basic sanity. Having the kernel tag means they can get excluded
for random non-kernel changes causing regressions. so remove kernel tag
to keep them in all CI runs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
uart0 is used as default console output in Zephyr. Change prevents
assertion fail in default configuration of hci_rpmsg sample. The
failing assertion is related to enabling logger without backend.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
If the test is run in a board that has a network interface
enabled, then the tests might select and use wrong network interface
that is needed for the test. So this commit makes sure that
we always use the simulated network interface for the
Ethernet management tests.
Fixes#36419
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
All variables for address, width and value are unsigned, so use strtoul
instead of strtol. This fixes an issue when 0xffffffff is about to be
assigned to specific address, which was truncated to 0x7fffffff so far.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Nuvoton provides different series MCU. The NPCX series has a specific
id, which can identify the real chip part number. This CL adds soc id
for the NPCX series.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Instructions to build enviroment setup
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
In west manifest to support esp32c3 when using
west install / update
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
For esp32c3 related ROM located functions instead
of esp32c3_rom.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
The _PrepC() function is the standard risc-v way
of zephyr entry point, so let it call the z_cstart instead
of calling this function directly.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
replaces the plain memcpy to zero the bss with
the standard zephyr function that does this task.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
And removes the odd esp32c3 competible from it
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Plus added implementation for esp32c3 SoC.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
