RT1050 has multiple LPSPI peripherals. The simplest to access is LPSPI1,
which can be connected by bridging solder jumpers on the board. Enable
this SPI peripheral, and set it as default for SPI tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Moves the Ethernet PHY reset routine on mimxrt1xxx_evk boards to execute
in the POST_KERNEL initialization level rather than the PRE_KERNEL_2
level because it relies on a kernel service, k_busy_wait(). Leverages
the existing CONFIG_PHY_INIT_PRIORITY to allow users to configure when
within the POST_KERNEL level this routine occurs, which by default is
set correctly to the following order:
Init Function Init Level Priority
--------------------------------------------------------------------------------------
sys_clock_driver_init PRE_KERNEL_2 CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
mcux_igpio_##n##_init POST_KERNEL CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
mimxrt1064_evk_phy_reset POST_KERNEL CONFIG_PHY_INIT_PRIORITY=70
eth_init POST_KERNEL CONFIG_ETH_INIT_PRIORITY=80
net_init POST_KERNEL CONFIG_NET_INIT_PRIO=90
This fixes an issue that was introduced in commit
f0b3146ff5, which caused the system timer
to be initialized after the Ethernet PHY reset. As a result, the
k_busy_wait() never returned and the kernel never finished booting. The
serial driver never initialized and there was no output on the console,
not even a boot banner.
Tested on the mimxrt1064_evk board with samples/net/dhcpv4_client.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
A change was put in to conditionalize pinmuxes based on
Ethernet configuration but for the IMXRT1050/60/64-EVK
boards the USER_LED and ENET_RST share the same GPIO.
Samples like blinky would not work on these boards.
The change is to not conditionalize the shared pin.
fixes: #27473
Signed-off-by: David Leach <david.leach@nxp.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Conditionalizes display pinmuxes on CONFIG_DISPLAY for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes ethernet pinmuxes on CONFIG_NET_L2_ETHERNET for all nxp
boards (kinetis, lpc, and imx families) to avoid possible conflicts
between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes i2c pinmuxes on CONFIG_I2C for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes spi pinmuxes on CONFIG_SPI for all nxp boards (kinetis,
lpc, and imx families) to avoid possible conflicts between peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Conditionalizes serial pinmuxes on CONFIG_SERIAL for all nxp boards
(kinetis, lpc, and imx families) to avoid possible conflicts between
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implementation of pinmux of usdhc depends on board design.
Usdhc driver could change pinmux according to SD mode, SoC
should provide API for this. Board pinmux should register
its pinmux function to SoC.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes board PHY initialization.
ENET_RST and ENET_INT pins are also used as USER_LED/JTAG_TDI and
INT1_COMBO/JTAG_TDO. Initialization needs to set these pins to power and
interrupt for the PHY Transciver. PHY reset works without busy waiting.
Moved pin initialization back to PRE_KERNEL_1 to fix UART bug and busy
wait not required.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Enables instance 3 of the lpuart driver, adds dts fixups, and configures
pinmuxes to use bluetooth hci on the mimxrt1050_evk board. Updates board
documentation accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables an instance of the lpspi peripheral, configures the pinmuxes,
and updates the board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the NXP MIMXRT1050-EVK board, an entry-level
development board for the new mimxrt1052 Cortex-M7 SoC.
Adds pinmuxing, dts, documentation, and jlink debug support for the new
board. Note that pinmuxing uses the mcux pinmux driver directly rather
than the Zephyr pinmux interface. The mimxrt1052 SoC has complicated
pinmuxing that may require changing the Zephyr pinmux interface to
support, so for now let's use the mcux driver directly.
We are also not yet configuring the external flash, therefore a debugger
is required to load code to the internal sram. The on-board OpenSDA
circuit with jlink firmware is sufficient, and the 'make debug' build
target is supported.
Samples tested include: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
