This allows the current speed of the connection (100Mbps/10Mbps) and
if it is operating in half or full duplex to be queried
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
The enc424j600 chipet has 1-byte commands to enable or disable
interrupts which an be used rather than the currently used 4-byte
commands to speed the process up by a factor of 4x
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
After system reset (SETETHRST) interrupt enable register (EIE)
has the default value 0x8010 and global interrupt enable flag (INTIE)
is set. This is not desired and the INTIE flag should be set only at
the end of the initialization.
Disable INTIE flag and set desired interrupts sources in
a single write command just right after system reset.
Resolves: #35091
Reported-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The controller has several interrupt sources which are signaled
via a single INT pin. Only the interrupt sources that are explicitly
switched on during controller initialization may generate an interrupt
signal. Currently there are only PHY Link Status Change Interrupt
and RX Packet Pending Interrupt enabled. So there is no other reason why
an interrupt can be triggered.
Terminate interrupt handling thread on unknown interrupt
only when debugging, as there are concerns that stopping
thread in the field is going too far.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Initialize device pointer in driver's context.
It was not done quite right in commit a1708cf2f2
("drivers: ethernet: Fix device instance const qualifier loss"),
and then completely removed in commit 113d9274ea
("drivers: ethernet: remove stray expression")'
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
An unnecessary expression that doesn't compile was inadvertently
introduced in the device constification PR. Remove it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Passing driver's data to k_thread is sufficient for mcux.
On enc424j600, however, the device pointer is needed and thus is wrapped
into its data. But there seems to be a possible optimisation: all local
spi related function in fact only needs the device's data (context) and
so changing all spi related function to take the context would remove
the need to wrap the device pointer into its data.
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a working code, but it's harder to read. And for some reason
makes some semantic patches of coccinelle running forever.
So refactoring it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Set the network interface up / down according to link status.
This means that we call Ethernet carrier on/off function in
proper places.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
