Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The various STM32 reference manuals sometimes define the USB endpoints
as IN or OUT only and sometimes as bidirectional, even in the same
manual. This is likely because the OTG implementation has one set of
registers for the IN endpoints and one other set for OUT endpoints.
However at the end a given endpoint address can both transmit and
receive data.
This causes some confusion how to declare the endpoints in the device
tree, and depending on the SoC, they are either the same number of IN
and OUT endpoints declared, or they are declared as bidirectional. At
the end it doesn't really matter given how the driver uses those values:
#define NUM_IN_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_IN_ENDPOINTS)
#define NUM_OUT_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_OUT_ENDPOINTS)
#define NUM_BIDIR_EP NUM_OUT_EP
This patch therefore cleanup the driver, the DTS, and the DTS fixups to
only define the number of bidirectional endpoints.
In addition to the cleanup, that fixes a regression introduced by commit
52eacf16a2 ("driver: usb: add check for endpoint capabilities"), which
introduced a wrong check for SoC only defining the number of
bidirectional endpoints.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add fixup info for PWM nodes on STM32F0/F1/F3/F4/L4 and remove the
conflicting Kconfig symbols to fully switch STM32 PWM to device tree.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
This commit moves the bit timing (PROP, BS1, BS2 segments and SWJ)
from Kconfig to the device-tree and fixes issue #7933
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
STM32Lx LPUART peripherals do not fit well into existing U(S)ART
port numbering scheme, so there will be two separate namespaces
in Kconfig: one for U(S)ARTs and one for LPUARTs.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Indexed defines were systematically generated even when there
was only one element to generate.
So we ended up generated a lot of _0 defines.
Then we needed to generate aliases to these _0 indexed defines,
in order to get useful defines.
For instance:
#define GPIO_LEDS_0_GPIO_FLAGS_0 4
#define GPIO_LEDS_0_GPIO_PIN_0 5
#define GPIO_LEDS_0_GPIO_FLAGS GPIO_LEDS_0_GPIO_FLAGS_0
#define GPIO_LEDS_0_GPIO_PIN GPIO_LEDS_0_GPIO_PIN_0
This commit allows to generate _0 indexed define only if a
property has more than one elements to define.
Aliases generation to _0 indexed defines are also removed.
Note: IRQ are left untouched since this is frequent to handle
multiple IRQs in a driver
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add SPI fixup defines on STM32 SoC family level for all SPIs that
are supported on one or more SOCs of that SoC family.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
