Fix for conversion of temperature values in adxl367_temp_convert
and missing break statement.
Signed-off-by: Vladislav Pejic <vladislav.pejic@orioninc.com>
Fix for SPI communication when RTIO is used in SPI driver. When in
adxl367_bus_access, const struct spi_buf buf[3] is used,
spi_rtio_copy function won't set correct buffers and length
for buf[2] and that will cause exception when that buffer is
processed.
Signed-off-by: Vladislav Pejic <vladislav.pejic@orioninc.com>
Due to the possibility of simultaneous accesess to LRCCONF registers,
additional management is required.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
DMA transfers do not execute when the USBD peripheral is in Low Power
mode. Make sure that there is no DMA active transfer when entering Low
Power mode and that new DMA transfers are not started when in Low Power
mode because the transfer won't ever finish.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Low Power mode can only be entered when there are no active DMA
transfers. Move the Suspend and Resume processing to thread to allow
waiting for the DMA available semaphore in USB Suspend handler.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
This commit adds the pfic interrupt controller driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the usart driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the systick driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the clock driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the pinctrl driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
TX part of interrupt driven API was not calling PM device runtime
API. Additionally, when txstopped occurred after poll out it was
not handled correctly.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add a timeout to the `bme280_wait_until_ready` loop to ensure that we
never get stuck in this loop even if the bus enters an error condition.
Signed-off-by: Jordan Yates <jordan@embeint.com>
The lp5569 has multiple pwm outputs, and thus implementing the
write_channels api to set multiple values in a single call makes sense.
Implement the write_channels function with a basic range check on the
channel range.
Since the lp5569 supports auto-increment, all of the channels can be
written in one i2c transfer, starting from the pwm register of the
start_channel.
Signed-off-by: Emil Dahl Juhl <emdj@bang-olufsen.dk>
The lp5569 controller supports auto-increment for its registers. This is by
default enabled in the chip, but the driver actively disabled it.
Since auto-increment is useful for writing multiple consecutive registers,
enable the feature. The driver, however, doesn't perform such consecutive
writes and thus the existing behavior is not altered.
Signed-off-by: Emil Dahl Juhl <emdj@bang-olufsen.dk>
The SSP driver has odd dependency to outside definition of
CONFIG_INTEL_NM. This is in practise tied to SSP hardware
version and always enabled for SSP block version 1.0.
Use the new SSP_IP_VER define to replace the CONFIG_INTEL_MN
preprocssor checks. Also modify the board test case to
remove the obsolete config setting.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
The blobs are now part of nrf_wifi module, and remove the manual check
and add verifying the blobs and their integrity using helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The shim files should be part of the Zephyr module directory within
Zephyr, as they are coupled with the module implementation which os OS
agnostic.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Following the naming convention add an underscore and update path in the
maintainers file too.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Do not enable the video sw generator if a real camera is present. This
helps to save some spaces and to avoid unrelated code going
into the built image.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add Bluetooth HCI driver for STM32WB0x series.
Modify CMakeLists.txt to compile the driver based on its kconfig parameter.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
allows use of touch_sensor, rtc_counter, and wdt simultaneously by enabling
ESP_INTR_FLAG_SHARED when calling esp_intr_alloc()
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
The `Kconfig.defconfig` is not good place for put `select PINCTRL`.
Drop `select PINCTL` from `Kconfig.defconfig` and add it at each
driver's Kconfig.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Optionally write to ad559x register bit which increases DAC output range
from 0V to 2 x Vref.
The functionality has been tested on AD5593r.
The voltage at 4095 has been measured to 5.01 volts.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
The `default y`, which is coupled with
`depends on DT_HAS_WOLFSON_WM8904_ENABLED` to link the settings with
DeviceTree, which was missing, so I added it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
- Add SPI driver support for RA
- RA2A1 not support slave select keeping level so disable it
in Kconfig
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
