Add the pinctrl state name (default) for the UART/USART/LPUART
peripherals. Changes performed using the following Python script run
from the repository root:
```
from pathlib import Path
import re
for fpath in Path(".").glob("boards/arm/**/*.dts"):
lines = open(fpath).readlines()
is_stm32 = False
for line in lines:
if "stm32" in line:
is_stm32 = True
break
if not is_stm32:
continue
with open(fpath, "w") as f:
for line in lines:
f.write(line)
m = re.match(r"(\s+)pinctrl-0.*us?art.*", line)
if m:
f.write(m.group(1) + "pinctrl-names = \"default\";\n")
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Rename the Zephyr chosen property for specifying the default CAN bus
controller from "zephyr,can-primary" to "zephyr,canbus".
The "zephyr,can-primary" property name was selected in antipation of
adding support for redundant CAN networks, which we have yet to
add. Meanwhile, the "primary" term causes confusion for non-redundant
CAN bus configurations (and the "can" term doesn't match the name of the
Zephyr CAN bus subsystem).
The CAN in Automation (CiA) 302-6, which deals with CANopen network
redundancy, uses the terms "default interface" and "redundant
interface". If/when we add support for redundant CAN networks, the
"zephyr,canbus" chosen property can be supplemented with a
"zephyr,canbus-redundant" chosen property.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update PWM pinctrl signal names of all non-F1 STM32 boards.
`pwm` variant is not available anymore on non-F1 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move SPI pin configuration to device tree for all STM32 based
boards.
This should not bring any change in pin configuration.
Though, some adjuments have been made on following boards for
coherency:
* b_l4s5i_iot01a1: Removed "very-high-speed" on SPI3 MOSI pin.
Tested with no impact.
* black_f407zg_pro: SPI1 pins configured but not SPI1 node.
Removed pin config as not documented neither.
* sensortile_box: SPI2 pins configured but not SPI2 node.
Removed pin config as not documented neither.
* nucleo_g431rb/nucleo_g474re/nucleo_l476rg/nucleo_l4r5zi:
SPI2 and SPI3 pins were configured but missing.
Added since they were documented.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pinctrl-0 property for CAN nodes and remove pinmux.c.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Martin Jäger <martin@libre.solar>
Use the new DT facilities to configure PWM pinmux on NUCLEO-L452RE and
NUCLEO-L452RE-P boards.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Support for the Nucleo L452RE-P has been added. Since it's very similar
to L452RE board, both of them have been added under the same directory.
The main difference is that the P version contains a SMPS but Zephyr is
not taking advantage of it yet.
I've tested the results in a real L452RE-P board.
Signed-off-by: Xabier Crespo Álvarez <x.crespo@scrobotics.es>
