Add the pinctrl state name (default) for the UART/USART/LPUART
peripherals. Changes performed using the following Python script run
from the repository root:
```
from pathlib import Path
import re
for fpath in Path(".").glob("boards/arm/**/*.dts"):
lines = open(fpath).readlines()
is_stm32 = False
for line in lines:
if "stm32" in line:
is_stm32 = True
break
if not is_stm32:
continue
with open(fpath, "w") as f:
for line in lines:
f.write(line)
m = re.match(r"(\s+)pinctrl-0.*us?art.*", line)
if m:
f.write(m.group(1) + "pinctrl-names = \"default\";\n")
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
USB devicetree nodes in Zephyr have different names,
mostly derived from the designations in data sheets.
Add zephyr_udc0 (USB device controller) nodelabel to
specific USB node to allow generic USB sample to be build.
Follow up on commit b4242a8 ("boards: add USB node aliases")
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Mass conversion of STM32 boards to dts based clock configuration has
left some minor whitespace issues. Fix these and some other whitespaces
in the affected files.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Enabling DAC support for STM32 nucleo_f429zi in device tree.
Documentation has been updated.
Signed-off-by: Sidhdharth Yadav <sidhdharth.yadav@hcl.com>
Update PWM pinctrl signal names of all non-F1 STM32 boards.
`pwm` variant is not available anymore on non-F1 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move STM32 based board USB pin configuration to device tree.
Exceptions:
* olimex_stm32_h407: Node not enabled and not documented.
Signal added in disabled node.
* L0/G4 based boards as signals are not available yet.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move SPI pin configuration to device tree for all STM32 based
boards.
This should not bring any change in pin configuration.
Though, some adjuments have been made on following boards for
coherency:
* b_l4s5i_iot01a1: Removed "very-high-speed" on SPI3 MOSI pin.
Tested with no impact.
* black_f407zg_pro: SPI1 pins configured but not SPI1 node.
Removed pin config as not documented neither.
* sensortile_box: SPI2 pins configured but not SPI2 node.
Removed pin config as not documented neither.
* nucleo_g431rb/nucleo_g474re/nucleo_l476rg/nucleo_l4r5zi:
SPI2 and SPI3 pins were configured but missing.
Added since they were documented.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new DT facilities to configure ADC pinmux on all boards with
STM32 MCUs currently supporting the ADC.
Signed-off-by: Martin Jäger <martin@libre.solar>
Update boards that use to declare ethernet support to enable
matching ethernet node.
Similarly to other devices, use dts API to control ethernet pin
settings.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add arduino_header support to nucleo f429zi board.
Create a dedicated connector file to hold arduino connector
information for nucleo_f429zi board.
Add missing arduino_spi feature to yaml file.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add partition table to support MCUBoot. A paragraph of
usage comments was also added in the board documentation.
Signed-off-by: Jun Li <jun.r.li@intel.com>
Now that stm32 watchdog should be configured by device tree,
update dts file of boards declaring watchdog support.
Additionally update doc and yaml files.
Add support on some boards that were used to validate the driver
update:
- disco_l475_iot1
- nucleo_f207zg
- nucleo_f429zi
- nucleo_f746zg
- nucleo_f073rz
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable USB on nucleo_f249zi.
Update clock to allow precise USB clock.
Tested on samples/subsys/usb/cdc_acm
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for button nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable and configure I2C1.
This configuration enables ready to use compatibility
with expansion shields based on Arduino type connectors
Additionally, fix comment on clock speed in board _defconfig
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
