Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The ouput speed of the gpio pins passed via the 'conf' argument was
ignored, causing the speed to always be in its reset state (lowest
possible speed for most pins). This was causing problems for pins that
actually need a speed faster than the default, like the ethernet
controller pins.
Combined with the correct pinmux configuration this fixes problems
of the olimex_stm32_e407 board not being able to send ethernet data.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
With introduction of commit "pinmux: stm32: directly return error if
stm32_get_pin_config fails", pin configuration fails when
pins are not configured in pins[] array.
This was the case for configuration UART1 assigned on PB6/PB7.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The bitfield determining the I/O direction already defines the pin
as either input or output, cannot be none or both at the same time
This issue was reported by Coverity
Coverity-CID: 151970
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xC tag in the SoC reference indicates the flash size, use it in the
configuration to permit selection of correct flash size for dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for STM32L475xG SoC as a preliminary for
Discovery IOT board support.
stm32l476.dtsi file is now including stm32l475.dtsi
since STM32L476 SoC is a STM32L475 SoC with LCD support
Change-Id: I7567255e4172231cbf4899474617ecae0cd68d64
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. There are few places we dont convert over to the new
types because of compatiability with ext/HALs or for ease of transition
at this point. Fixup a few of the PRI formatters so we build with newlib.
Jira: ZEP-2051
Change-Id: I7d2d3697cad04f20aaa8f6e77228f502cd9c8286
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since all the L4 SoCs are using DTS we can remove the various Kconfig
bits that we now get from DTS.
Change-Id: Icdec49b478ff285dc3347b09412964a721f75bbf
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move back to getting the number of IRQs from Kconfig. We do this
because the number of IRQs should really just be determined by scanning
the device tree and figuring out the highest IRQ value used.
Change-Id: I8e0dbec1d9d036d4e899b237c4dc7d833c422e18
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Cube HAL implements timeout based on 1ms tick.
This commit allows Cube HAL to get Zephyr system clock.
Change-Id: I9a59edcf6fa8e0ebfd5040348db537dadd9fcdfa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native L4 Clock control driver.
Change-Id: Ic0408d5f5ec66651d46d13dfaf447da2666367cd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32l4x soc.
Clean up will have to be done afterwards.
Change-Id: I979a4169148c5fe5a0693d182d2d17f9ffaf1c77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds all the necessary changes to enable use of DTS for
generating required build information.
Change-Id: Ia476fbb14c7d9d6b9db3340c73f599556a880da3
Signed-off-by: Andy Gross <andy.gross@linaro.org>
A number of SoCs clear out the Mem/Bus/Usage and Hard Fault exceptions
during init. Lets refactor that into a common function so we don't have
to keep duplicating it over and over.
Change-Id: Ida908a9092db37447abcf3c9872f36937982f729
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It is called before early SoC initialization, so remove the duplicated
code from other boards and just set it by default when using XIP.
This can later be used when adding bootloader support, as an
additional option could be created to move the VTOR offset to a
different address.
Change-Id: Ia1f5d9a066de61858ee287215cefdd58596b6b1c
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Following pinmux update for PWM support,
update soc to support this new configuration.
Change-Id: I1126e347ab1ab6b2d830993e548de8f32fa2f8f9
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add one pin configuration for I2C1 of the STM32L4 series.
Change-Id: Id05d916f2a1126ca439aebcddd8dc9c91015f6fe
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the pin configuration of the USARTs.
Change-Id: Idf7a18b6eab95c61870ad4850c9eafb1fdcab03d
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the clock driver for the STM32L4 series.
Change-Id: Icdf79061f163d8d00187b382d1564422fb875c5b
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the initial SoC support for the STM32L4XX family. The code was
tested on STM32L476RG, but should work on any STM32L4XX currently
available.
This implementation was inspired by the stm32f1x implementation.
Change-Id: Id6670bce0c423617284e8467a9c461531f948e0f
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
