Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add support for an alternate clock. If available,
alternate clock is enabled and used to get the
device clock rate.
Based on: #45053.
Signed-off-by: Artur Lipowski <Artur.Lipowski@hidglobal.com>
Previously, the uart_stm32 driver was extended in #44487 to support
swapping the tx and rx pins of supported STM32 UART peripherals.
However, the original change applied this configuration during the
call to the uart_stm32_configure() function. This has now been added to
the uart_stm32_init() function to ensure this behavior on startup for
ports like the virtual com port.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Cyclone V SoC FPGA supports 128Byte FIFO for UART communication,
this modification adds a feature to use 128byte FIFO serial UART
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Pretend that the serial test driver supports the interrupt and async
API's, as these can be required for various drivers. Also select
`SERIAL_HAS_DRIVER` so that the serial library will be included.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Depending on `!SERIAL_SUPPORT_INTERRUPT` to enable the driver does not
make any sense, as this is a symbol selected by drivers to signify that
they support interrupts. Simply not selecting this symbol is enough to
convey the desired intention.
This fixes Kconfig problems when the driver is compiled together with
a dummy serial driver which does select `SERIAL_SUPPORT_INTERRUPT`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds addresses and names for individual CSR registers to device tree.
This way liteuart driver no longer depends on CSR data width being 8
bits.
Also when register names or their number changes, then overlay generated
by LiteX will be incompatible with one defined here.
This should make finding breaking changes easier.
I also appended `_ADDR` suffix to defines, to distinguish them from
normal values like `UART_EX_TX`.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Use LiteX HAL functions instead of `sys_read*` or `sys_write*`
functions.
They use them inside, but choose which one to use according to
configured CSR data width.
Signed-off-by: Michal Sieron <msieron@internships.antmicro.com>
Old code only create one pl011 device instance though there are two or
more pl011 device defined in devicetree. This patch can fix this issue.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
LPUART driver should use shared ISR for all possible use cases,
including ASYNC API, so that multiple features requiring ISR can be
enabled simultaneously.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
This PR enables the Ansynchronous UART API for using the MCUX drivers.
It is tested on the RT1062EVKB.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
Extend Altera Jtag Uart driver support without Altera HAL driver
by default. uart_altera_jtag_hal.c renamed to uart_altera_jtag.c and
new config, CONFIG_UART_ALTERA_JTAG_HAL is introduced to allow driver
to use Altera HAL driver when needed.
Signed-off-by: Khor Swee Aun <swee.aun.khor@intel.com>
Only compile in async related code when at least one UARTE instance has
enabled async mode. This fixes an "unused function" warning when
`CONFIG_UART_ASYNC_API` is enabled but no UARTE instances has async
enabled. This is possible when the async API is being used for an RTT
UART driver.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Rather than specify input clock for each peripheral individually, instead
specify the relevant clocks in DTS.
This will enable easier support for non-default coreclk on fe310 in a
follow-up CL.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
Add a new boolean devicetree property `tx-rx-swap` to the
st,stm32-usart binding, used to control TX/RX swap during
device initialization.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Instead of selecting appropriate HAS_HW_NRF_* options for particular
nRF SoCs (and simulated nRF52 target), set their values basing on
information from devicetree.
Correct also semantics of those options so that they are set only when
a corresponding DT node is enabled. This allows using them directly in
Kconfig dependencies of Zephyr drivers for nRF peripherals. Update
appropriately these dependencies.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The function in its current form is confusing because unlike other
similarly named functions (dt_nodelabel_has_prop(), dt_node_has_prop())
or devicetree macros (DT_NODE_HAS_COMPAT(), DT_NODE_HAS_PROP()), this
function takes into account the status of the checked node and returns
"y" only when the node is enabled.
This commit redefines dt_nodelabel_has_compat() so that it no longer
checks the node status, and for cases where the previous functionality
is needed, a new function named dt_nodelabel_enabled_with_compat()
is introduced as a replacement.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When NO_OPTIMIZATIONS is set and asynchronous API is used but
HW counting is not enabled then linking fails because of lack of
nrfx_timer code. When optimization is enabled, linker is smart
enough to figure out that nrfx_timer is not used.
Converting decision function from static inline function to macro
which is handled correctly with optimization off.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Fixes a case for the asynchronous UART API where
only single buffer was attached to the UART, after
filling this buffer release event was trigger first
time and after disabling UART the release event was
triggered again for the same buffer.
Signed-off-by: Kamil Gawor <Kamil.Gawor@nordicsemi.no>
This commit makes the transition from the pinmux driver to the pinctrl
driver. It also modifies UART, SPI and I2C drivers used in FE310-based
boards to use the new pinctrl API.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Extend the macro with checks for DT properties related to pin
assignments that are defined but would be ignored, depending on
whether PINCTRL is enabled or not, what presumably indicates
a resulting configuration different from what the user expects.
Add also a possibility to indicate that the pinctrl-1 property
should not be checked because the caller does not support the
sleep state.
Rename the macro so that its name better reflects its function.
Update accordingly all drivers that use it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Values of boolean DT properties need to be checked with DT_PROP(),
not DT_NODE_HAS_PROP(). Fix two such incorrect calls in the nRF UART
driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This macro incorrectly uses DT_NODE_HAS_PROP() to check the truth value
of the "disable-rx" boolean property. In consequence, it always assumes
that RX is disabled and the low power mode needs to be used. Fix this
by replacing the check with DT_PROP().
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The pm_constraint_* APIs were effectively used by the policy manager
only. This patch renames the API to the policy namespace and makes its
naming more explicit:
- pm_constraint_set -> pm_policy_state_lock_get()
- pm_constraint_release -> pm_policy_state_lock_put()
- pm_constraint_get -> pm_policy_state_lock_is_active()
The reason for these changes is that constraints can be of many types:
allow/disallow states, impose latency requirements, etc. The new naming
also makes explicit that the API calls will influence the PM policy
behavior.
All drivers and documentation have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
gpio_pin_interrupt_configure asserts that one of GPIO_INT_ENABLE or
_DISABLE is specified by the caller, and also that GPIO_INT_EDGE is
requested if both states (GPIO_INT_TRIG_BOTH) should interrupt. This
change corrects the misuses in it8xxx2 drivers that cause assertion
failures.
When assertions are disabled the existing code works correctly because
the it8xxx2 GPIO driver assumes that a pin interrupt should be enabled
if _DISABLE is not requested, and the driver only supports edge
triggers but assumes the absence of GPIO_INT_MODE_LEVEL indicates
an edge trigger was requested.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Change-Id: I1aaee190ec4cf063f36e25c0c293a91d280e71bb
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add build assertions that will ensure that every peripheral for
which a driver instance is created has some pins assigned to it.
Neither pinctrl-0 nor *-pin properties can be currently marked as
required in devicetree, so these assertions will help users avoid
invalid configurations where it could be hard to figure out why
the UART is not working.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
System entering sleep state before uart tx is complete can result in
characters being dropped from the transmission. Add pm constraint
setting to the lpuart driver to prevent character drops
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
