Several GPIO device drivers support only one of the two possible
access_op modes and return an errno error code for the mode they do
not support. Use the same errno code across all drivers.
Change-Id: Ic01ce9dee7fb2405d254c60cebee22053c803270
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Several GPIO drivers detect an out of range pin number and return an
errno error code. Use the same errno code across all drivers.
Change-Id: I0e2949432d6845d12c37064c78f9c228b8e8e45a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Several gpio drivers consider GPIO_INT with GPIO_DIR_OUT to be illegal
and return an errno code. Use the same errno code across all drivers.
Change-Id: I1594df0cfdf96194685c83c34dff36261896f2de
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This flag is no longer necessary and TICKLESS_IDLE will be
enabled by default if SYS_POWER_MANAGEMENT is enabled.
Jira: ZEP-1325
Change-Id: Ic6cd4b8dc0a17c6a413cabf6509b215a4558318d
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Update the builtin QMSI code to 1.4 (RC2).
The below shim drivers were updated for API or interface changes:
- aio
- counter
- i2c_ss
- rtc
- wdt.
Also, arch soc specific power management code were updated.
Jira: ZEP-1572
Change-Id: Ibc8fae032a39ffb2c2c997f697835bc0208fd308
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
If subcription was found within the subscription list,
we have check if remains identical subscription
from the next node.
Otherwise none unsubscription is realized.
Change-Id: I38132d7c80575801885b8057902f3d4666b08aea
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The driver was using net_buf_unref(). This technically works
ok but debugging the network buffer allocations is more
difficult if done like this.
Change-Id: If3453a49337c7a359c8af22cfdf331fccc697af5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit splits 802.15.4 drivers configuration into separate files.
Change-Id: Ie1bed862e8f4248240fef18bc211d0ee8ca1493c
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The DW i2c driver chooses to return -EPERM following a PCI error in
driver configuration. This seems an odd choice. All of the other I2C
drivers return -EIO for general failures detected during driver
configuration.
Switch the DW driver from EPERM to EIO.
Change-Id: Ia4f96386620319736ae4c09212b0a05ea38169b1
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The I2C drivers handle an empty list of I2C messages inconsistenty.
There are two different behaviours, one set of drivers dectects a
requests to transfer zero messages and return -EINVAL while the other
group simple transfer no data and return success.
Adopt the latter behaviour consistently across all drivers. Update
the i2c.h API documentation to reflect this behaviour.
Change-Id: I427fc1b0e18ddc04b7b59c294e0240b3d6ca4073
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Subscribe value is set to zero before calling notify callback,
to distinguish a subscription failure from an unsubscription
on disconnection (when flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE is set).
Change-Id: Ia91220492d82041b2c385bf88a15180387e7a483
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
Some application protocol required non-persistente subscription
across connection even in bonded case.
Flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE specify if subscription
must be remove during disonnection.
Change-Id: I1bc2bbbb4bc86f58905e44a7eb267ca0871f2fdb
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
Implement the missing port read and write behaviour.
Change-Id: I0928379eddf81d806a0ae6b75a1ea2993c3a28ff
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Adjust the implementation of gpio_pin_read() to return 0 or 1 rather
than 0 or 2^pin. This ensures consistent behaviour with other gpio
device drivers, and conforms to the behaviour documented in gpio.h by
the previous patch.
Change-Id: Ia02aa68105a406f355d16a3f9b0550f948658483
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The subscriptions callback may free or reuse the subscription so all
instances that where this could happen need to safely fetch the next
element which is why this changes switch to use sys_list_t as it has
SYS_SLIST_FOR_EACH_NODE_SAFE.
Change-Id: I37d51f27116ea0c057b560924a9416676477597b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reduce the pressure on the common RX buffer pool by reusing HCI
command buffers also for the Command Status or Command Complete
response to them. This also implies removing the existing Kconfig
variable for the command buffer sizes since the size is also dependent
on maximum Command Complete event sizes. Instead, reuse the RX buffer
size also for HCI Command buffers.
Change-Id: I006b287d64a0c9ca40de741aa9a424a49a927385
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A subsequent patch will start reusing HCI command buffers for
receiving the response, so the distinction of received vs sent data
headroom would just make the code unnecessarily complex. Instead, just
merge these two variable into a single one.
Change-Id: I31d846331939f1a2270df7ed0c75112825e16493
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we are low on RX buffers and receive an LE Advertising Report or a
BR/EDR Inquiry response we should just discard this. If we don't
discard the event we increase the risk of deadlock where the RX
interrupt is enabled but bt_recv() is doing a synchronous HCI command
sending, i.e. waiting for a cmd_status/cmd_complete (which will never
come since the RX interrupt is disabled).
Change-Id: I6266625c9790d68bcf8e8718c8c36f127946c4c6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add sensor sample ready check before fetching the sample.
Otherwise, invalid value will be returned.
Jira: ZEP-1532 ZEP-1358
Change-Id: I570151c8ae93fbb744dac857521f596fd63806a6
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
riscv defines the machine-mode timer registers that are implemented
by the all riscv SOCs that follow the riscv privileged architecture
specification.
The timer registers implemented in riscv-qemu follow this specification.
To account for future riscv SOCs, reimplement the riscv_qemu_driver by
the riscv_machine_driver.
Change-Id: I645b03c91b4e07d0f2609908decc27ba9b8240d4
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This is a zero-copy networking implementation of Ethernet driver.
Limitations:
- one shot PHY setup, no support for PHY disconnect/reconnect
- no support for devices with DCache enabled due to missing
non-cacheable RAM regions in Zephyr.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: Ib944f91193efbd12c1142b0bcf1f635388bf1b87
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
I found that I was not getting the i2C interrupt.
When CONFIG_I2C_0_IRQ_DIRECT=y, it is acceptable to just
pass the constant to irq_enable.
See ZEP-1651.
Change-Id: I10955e6d6fe5fdd2dda916c92c8bc8a2e871f41a
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Replace _ScbExcPrioSet with calls to NVIC_SetPriority as it handles both
interrupt and exception priorities. We don't need to shift around the
priority values for NVIC_SetPriority.
Jira: ZEP-1568
Change-Id: Iccd68733c3f7faa82b7ccb17200eef328090b6da
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The newer version of mcux changes its flash api slightly, so update the
Zephyr shim accordingly.
Change-Id: I0c974fc3e82b9f40372c636f0b805ed143be2198
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
spi_transceive can return successfuly even if the data provided by the
slave is invalid, so check if the content is correct and retry until a
valid data is available.
Change-Id: Ia951de391e0b24c5b41eeabfb5c10b056d32b62e
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Drop the BLUETOOTH_SPI_RX_BUFFER_SIZE and BLUETOOTH_SPI_TX_BUFFER_SIZE
config options by fixing the max SPI buffer length to 255, as used by
the X-NUCLEO-IDB04A1 BSP. This simplifies the rx/tx buffer handling, and
avoids a potential spi rx stack overflow depending on the config values
set by the user.
Change-Id: Ifa7fd086016abda4bdcf9638f28b38d001a288c5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This new option is used to encapsulate the logic specific to devices
implementing the BlueNRG Bluetooth stack (e.g. X-NUCLEO-IDB05A1).
The current BlueNRG specific logic covers the HCI Reset handling and
the manual control of the SPI Chip Select line (normally not needed since
spi_transceive is also responsible for controlling the SPI CS line).
Change-Id: I5db4addf873eee0af2d957e2181c50aac53ab656
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Change BREDR_NAME to DEVICE_NAME so it can also be used as the LE
device name.
Change-Id: I9ef55d9dff098372d47d9d5754ad7a7163a65bc0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Code was assuming that all the HCI messages were events, causing invalid
data length when receiving HCL ACL packets.
Change-Id: I8c1a07f46b6b62a04e242cf29ee1119f59d4bda6
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
SENSOR_CHAN_*_ANY will be deprecated, so use the new SENSOR_CHAN_*_XYZ
enum values.
Change-Id: I91cf25864613a934feab65588969d10c52fd4fe6
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Thus users won't have to first enable network stack and then telnet.
Change-Id: I30cb2b9debee3feaf804f9a70f9d3f90758f5f17
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is the skeleton for such support. Let's see if this will be needed
and thus extended in the future.
For now, it's disabled by default, not advised to be enabled.
It supports AYT, AO and DO/SUPR_GA. This is very limited and only there
to show how it could be handled.
Change-Id: I736bfa23145e9b727af08db682ab001f494f8c8d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
