Reducing the heap requirement for the hci_ipc sample from
8KiB to 4KiB. It has been tested in various configurations to
work with 2300, but 4KiB was used to provide some leeway for
future updates.
The heap requirement is not documented, and it is unclear why
values lower than 2300 (not exact number) won't boot, and should
be investigated further.
Memory has become a very scarce resource for especially the ISO
builds for the nRF5340, which is why this is getting reduced.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The SSP driver has odd dependency to outside definition of
CONFIG_INTEL_NM. This is in practise tied to SSP hardware
version and always enabled for SSP block version 1.0.
Use the new SSP_IP_VER define to replace the CONFIG_INTEL_MN
preprocssor checks. Also modify the board test case to
remove the obsolete config setting.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Use Kconfig to configure watchdog instead of using expensive filters.
Also disable CONFIG_TEST_HW_STACK_PROTECTION for this test so we do not
have to create special cases.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enabling CONFIG_FPU and CONFIG_FPU_SHARING requires the
definition of `arch_float_disable` and `arch_float_enable`.
Signed-off-by: Matthias Alleman <matthias.alleman@basalte.be>
This fixes memory corruption of delayable work when
tests executes unsupported function.
When test (e.g. only_rx_in_chunks) is executed it starts
delayed work for master functionality (with 10 ms delay).
Later when slave function is tried and reports that
function is unsupported, test is terminated (task ends)
but work is still scheduled.
When next test starts it clears work that is already
scheduled:
static void before(void *not_used)
{
ARG_UNUSED(not_used);
memset(&tdata, 0, sizeof(tdata));
this leads to memory corruption and system work queue
tries to remove work but it never does since head/next
pointers are zeroed at that time.
This just adds after function that cancels work
regardless if it was scheduled or not.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
The blobs are now part of nrf_wifi module, and remove the manual check
and add verifying the blobs and their integrity using helper function.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
The shim files should be part of the Zephyr module directory within
Zephyr, as they are coupled with the module implementation which os OS
agnostic.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Following the naming convention add an underscore and update path in the
maintainers file too.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Do not enable the video sw generator if a real camera is present. This
helps to save some spaces and to avoid unrelated code going
into the built image.
Signed-off-by: Trung Hieu Le <trunghieu.le@nxp.com>
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Most likely there is no point of synchronizing RTC if net core is
not enabled. Same for the bootloader.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Replacing "area: Networking" with "area: PTP" to prevent from
including myself in issues and PRs that are related to every
piece of Networking code. Insted I'll be included only in PTP
related issued/PRs.
Signed-off-by: Adam Wojasinski <awojasinski@baylibre.com>
Enable BLE feature for Nucleo-WB09KE and Nucleo-WB05KZ.
Dedicate 32KB and 8KB at the end of flash memory to storage partition on
Nucleo-WB09KE and Nucleo-WB05KZ respectively.
Add ble tag to the both devices yaml file.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Put the default value for BT_AUTO_PHY_UPDATE and BT_AUTO_DATA_LEN_UPDATE
to "n" at SOC level since they cause "controller busy" due to starting
several parallel BLE procedures during connection by
"perform_auto_initiated_procedures" function. At the moment, ST controller
does not support parallelism, i.e. host should not initiate a new procedure
before previous one is completed.
Disable CONFIG_BT_HCI_ACL_FLOW_CONTROL at SOC level.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Add Bluetooth HCI driver for STM32WB0x series.
Modify CMakeLists.txt to compile the driver based on its kconfig parameter.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
This PR adds arduino giga r1 overlay in the dac sample.
Arduino Giga R1 has a 3.5mm audio jack connected to the
dac.
Signed-off-by: Mario Paja <mariopaja@hotmail.com>
allows use of touch_sensor, rtc_counter, and wdt simultaneously by enabling
ESP_INTR_FLAG_SHARED when calling esp_intr_alloc()
Signed-off-by: Marcio Ribeiro <marcio.ribeiro@espressif.com>
The `Kconfig.defconfig` is not good place for put `select PINCTRL`.
Drop `select PINCTL` from `Kconfig.defconfig` and add it at each
driver's Kconfig.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
A warning could be generated when compiling with -Wtype-limits. This
works around the warning which could happen if initial_count is 0 and
count_limit is K_SEM_MAX_LIMIT.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The function does not return the language, but rather stores
the lang in the provided lang param.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
bt_conn_le_create logs a warning if the provided conn is
non-NULL which was the case here. Simply set it to
NULL as it is a local variable.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Optionally write to ad559x register bit which increases DAC output range
from 0V to 2 x Vref.
The functionality has been tested on AD5593r.
The voltage at 4095 has been measured to 5.01 volts.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
