Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
setting/resetting endpoints is required when switching to alternate
interfaces. This is a common operation for usb audio class.
When audio device is enumerated host invokes set_interface request
to alternate with 0 endpoints associated. That operation lead to
disable never enabled endpoints. With previous solution error message
will appear.
This commit limits error messages to be present only if endpoint
was configured/enabled before and there was a problem when trying
to configure/enable it for the first time.
* Kinetis driver was updated with return error value when ep was
already configured/enabled.
* nxp driver updated with return error value when ep was already
enabled
* sam0 driver updated with return codes instead of magic numbers.
This is fix patch to #21741
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Newer SoCs like SAME54 provide dedicated registers to store
the USB trim configuration.
Use those registers if they are defined in ASF to access the
calibration data.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
On newer sam0 SoCs peripherals are enabled through the MCLK
instead of the PM register.
Use the MCLK register if it's availiable.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Newer SoCs like SAME54 have multiple IRQs for the USB peripheral.
Automatically enable all IRQs configured in the DTS.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This implements three API functions that are required for
tests/subsys/usb/device to build:
- usb_dc_ep_disable()
- usb_dc_ep_halt()
- usb_dc_ep_flush()
While halt and disable are trivial, flush is just a stub for now.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Make sure the parameters for the API functions are valid, return error
otherwise.
This is expected by the tests/subsys/usb/device test case.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
There are issues using lowercase min and max macros when compiling a C++
application with a third-party toolchain such as GNU ARM Embedded when
using some STL headers i.e. <chrono>.
This is because there are actual C++ functions called min and max
defined in some of the STL headers and these macros interfere with them.
By changing the macros to UPPERCASE, which is consistent with almost all
other pre-processor macros this naming conflict is avoided.
All files that use these macros have been updated.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add USB_DBG, USB_WRN, USB_ERR, USB_INF macros
in usb_device header file and remove them
from usb device drivers.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add function to check capabilities of an endpoint.
Only basic properties are checked, especially on STM32
capabilities of different USB controller configurations
have to be considered in the future.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
