Adds handling of the FLOAT_64BIT option when determining the ISA
flags as well as introduces a new Kconfig option to enable/disable
the hard-float calling convention.
Signed-off-by: Corey Wharton <coreyw7@fb.com>
This change adds full shared floating point support for the RISCV
architecture with minimal impact on threads with floating point
support not enabled.
Signed-off-by: Corey Wharton <coreyw7@fb.com>
This operation is formally defined as rounding down a potential
stack pointer value to meet CPU and ABI requirments.
This was previously defined ad-hoc as STACK_ROUND_DOWN().
A new architecture constant ARCH_STACK_PTR_ALIGN is added.
Z_STACK_PTR_ALIGN() is defined in terms of it. This used to
be inconsistently specified as STACK_ALIGN or STACK_PTR_ALIGN;
in the latter case, STACK_ALIGN meant something else, typically
a required alignment for the base of a stack buffer.
STACK_ROUND_UP() only used in practice by Risc-V, delete
elsewhere.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The core kernel z_setup_new_thread() calls into arch_new_thread(),
which calls back into the core kernel via z_new_thread_init().
Move everything that doesn't have to be in z_new_thread_init() to
z_setup_new_thread() and convert to an inline function.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This commit reworks the ARM AArch32 non-Cortex-M (i.e. Cortex-A and
Cortex-R) exception handling to establish the base exception handling
framework and support detailed exception information reporting.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In the ARM Cortex-M architecture implementation, the concepts of
"exceptions" and "interrupts" are interchangeable; whereas, in the
Cortex-A/-R architecture implementation, they are considered separate
and therefore handled differently (i.e. `z_arm_exc_exit` cannot be used
to exit an "interrupt").
This commit fixes all `z_arm_exc_exit` usages in the interrupt handlers
to use `z_arm_int_exit`.
NOTE: In terms of the ARM AArch32 Cortex-A and Cortex-R architecture
implementations, the "exceptions" refer to the "Undefined
Instruction (UNDEF)" and "Prefetch/Data Abort (PABT/DABT)"
exceptions, while "interrupts" refer to the "Interrupt (IRQ)",
"Fast Interrupt (FIQ)" and "Software Interrupt/Supervisor Call
(SWI/SVC)".
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The exception/fault handling mechanisms for the ARM Cortex-M and the
rest (i.e. Cortex-A and Cortex-R) are significantly different and there
is no benefit in having the two implementations in the same file.
This commit relocates the Cortex-M fault handler to
`cortex_m/fault_s.S` and the Cortex-A/-R generic exception handler to
`cortex_a_r/exc.S` (note that the Cortex-A and Cortex-R architectures
do not provide direct fault vectors; instead, they provide the
exception vectors that can be used to handle faults).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The amount of shared code in exc_exit.S between the ARM Cortex-M and
the rest (i.e. Cortex-A and Cortex-R) is minimal and there is little
benefit in having the two implementations in the same file.
This commit splits the interrupt/exception exit code for the
Cortex-A/-R and Cortex-M into separate files to improve readability as
well as maintainability.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use calee saved register to preserve value accoss sequence.
Procedure calls are mandated to follow ABI spec and preserve
x19 to x29.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Zephyr being an OS is typically expected to run at EL1. Arm core
can reset to EL3 which typically requires a firmware to run at EL3
and drop control to lower EL. In that case EL3 init is done by the
firmware allowing the lower EL software to have necessary control.
If Zephyr is entered at EL3 and it is desired to run at EL1, which
is indicated by 'CONFIG_SWITCH_TO_EL1', then Zephyr is responsible
for doing required EL3 initializations to allow lower EL necessary
control.
The entry sequence is modified to have control flow under single
'switch_el'.
Provisions added by giving weak funcions to do platform specific
init from EL3.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Single mov instruction can not be used to move non-zero
64b immediate value to the 64b register.
Implement macro to generate mov/ movk and movz sequences
depending on immediate value width.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Random readability improvements:
- avoid a stack trace on error by using sys.exit()
- include "error:" in the error() output, for grep
- print conflicting addresses on multiple IRQ registration
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
To remove the need to have DT_NUM_IRQ_PRIO_BITS defined in every
dts_fixup.h we can just handle the few variant cases in irq.h. This
allows us to remove DT_NUM_MPU_REGIONS from all the dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To remove the need to have DT_NUM_MPU_REGIONS defined in every
dts_fixup.h we can just handle the few variant cases in arm_mpu.c
directly. This allows us to remove DT_NUM_MPU_REGIONS from all the
dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current implementation to preserve r0 and r3 registers around the
call to `read_timer_end_of_isr` function has the following problems:
1. STM and LDM mnemonics are used without proper suffixes, in attempt
to implement PUSH and POP (i.e. STMFD and LDMFD). The suffix-less
STM mnemonic is equivalent to STMEA (increment after), which clearly
is not a PUSH operation, and this corrupts the interrupt stack,
leading to crashes on the Cortex-R.
2. The current implementation unnecessarily preserves additional r1, r2
and lr registers. There is no need to preserve r1 and r2 because the
values contained in these registers are not used after the function
call; as for the lr register, it is already pushed to the stack when
the interrupt service routine enters.
This commit removes all the unnecessary register preservations and
fixes the incorrect STM and LDM usages.
Note that the PUSH and POP aliases are used in place of the STMFD and
LDMFD mnemonics because they are used throughout the rest of the code.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Currently, the Cortex-M SysTick-based timing info implementation is
incorrectly specified for all 32-bit ARM architectures.
This commit fixes that by restricting the SysTick-based implementation
to the ARM Cortex-M architectures only; in addition, it removes the
ARM64 timing info implementation as it is identical to the default
generic implementation and was previously added only as a workaround
for the aforementioned problem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The selection of the Cortex M systick driver to be used as a system
clock driver is controlled by CONFIG_CORTEX_M_SYSTICK.
To replace it by another driver CONFIG_CORTEX_M_SYSTICK must be set
to 'n'. Unfortunately this also controls the interrupt vector for
the systick interrupt. It is now routed to z_arm_exc_spurious.
Remove the dependecy on CONFIG_CORTEX_M_SYSTICK and route to
z_clock_isr as it was before #24012.
Fixes#24347
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
The ARM architecture root directory contains `aarch32.cmake` and
`aarch64.cmake` files whose contents are better suited to go into other
more purpose-specific files.
This commit removes the aforementioned files and moves their contents
to other files following the convention used by other architectures.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the GCC `-march` flag for the ARM Cortex-R5 targets.
Note that `armv7-r+idiv` must be specified instead of `armv7-r`,
because the GCC internally resolves `-mcpu=cortex-r5` to it.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This is a minor clean-up for the ARM architecture configurations.
Note that the `CPU_CORTEX_A` symbol is moved from the AArch64 to the
ARM root Kconfig because it can be selected from both AArch32 and
AArch64.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This bug is brought in commit 3f88ddd54999.
The cleanup of IRQ_ACT.U bit before thread switch is not done.
The bug comes out at the case where interrupt comes in user mode,
then a thread switch happens, and the target thread is to run in kernel
mode. Because the U bit is not sync up correctly, the stack operation
is wrong.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Those are used only in tests, so remove them from kernel Kconfig and set
them in the tests that use them directly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In arch_irq_connect_dynamic the 'level' variable is only used on
platforms that define CONFIG_RISCV_HAS_PLIC. For the other platforms
we'll get a warning about an unused variable. Remove the need for
'level' and just call irq_get_level() where its needed to address the
issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix documentation in kernel_arch_data.h and kernel_arch_func.h
headers for ARM, to indicate that these are common headers for
all ARM architecture variants.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
z_isr_install is not suited to handle multi-level interrupt formats.
This update allows z_isr_install to accept irq numbers in zephyr format
and place them in the isr table appropriately.
Fixes issue #22145
Signed-off-by: Jaron Kelleher <jkelleher@fb.com>
This moves enabling XTENSA_HAL to the SoC definitions.
As Xtensa SoCs are highly configurable, it is possible
that the generic Xtensa HAL provided in the tree is
not suitable. So only enable XTENSA_HAL only if
the generic version can be used.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
In the Cortex-M exception table we rename z_arm_reserved()
function to z_arm_exc_spurious(), as it is invoked when
existing (that is, non-reserved) but un-installed exceptions
are triggered, accidentaly, by software, or hardware. This
currently applies to SysTick and SecureFault exceptions.
Since fault.S is shared between Cortex-M and other AARCH32
architectures, we keep z_arm_reserved as a defined symbol
there. This commit does some additional, minor, "no-op"
cleanup in #ifdef's for Cortex-M and Cortex-R.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
If the Cortex-M core does not implement the Security Extension,
we should not be adding z_arm_reserved in the corresponding
vector table entry. That is because the entry is reserved by
the ARM architecture.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
If the Cortex-M core does not implement the SysTick peripheral,
we should not be adding z_arm_reserved in the corresponding
vector table entry. If we do have SysTick implemented but we
are not using it as the system timer, we shall install the
reserved interrupt at the vector table entry.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Write 0x0 instead of z_arm_reserved to vector exception
entries that are always reserved for future use by the
ARM architecture. These vector table entries cannot be
fetched to be executed by the Cortex-M exception entry,
so having z_arm_reserved gives a false impression, since
it is a function that may be invoked in the code. This
modification is safe since these vector entries are also
not supposed to be read / written by the code.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The mabi and march options of the compiler and linker commands
were previously hardcoded and depended only on the 64BIT config
option. This update allows these flags to be set by the config
options currently available, plus an additional option to
specify the compressed ISA.
Signed-off-by: Jaron Kelleher <jkelleher@fb.com>
When SMP is enabled, the irq_lock/unlock will get and
release a global spin lock, but the codes changed in this
commit only need to lock the local cpu. No affect on
uniprocessor, but optimizations for SMP case.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add interrupt lock in low level API to gurantee the
correctness of operations.
* make some functions as in-line functions
* clean up and optimize the code comments
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Now that all posix boards have a dts we can move the selection of
HAS_DTS to the arch level like it is for all the other architectures.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current context preservation implementation saves the spsr and
lr_irq registers, which contain the cpsr and pc register values of the
interrupted context, in the thread callee-saved block and this prevents
nesting of interrupts because these values are required to be part of
the exception stack frame to preserve the nested interrupt context.
This commit reworks the AArch32 non-Cortex-M context preservation
implementation to save the spsr and lr_irq registers in the exception
stack frame to allow preservation of the nested interrupt context as
well as the interrupted thread context.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The timer counter for ticks on MEC1501 SoC is based on the RTOS
timer which runs at 32kHz. This is too slow for timing benchmarks
as most cases can be finished within one or two ticks. Since
the SoC has higher frequency timers running at 48MHz, add
the necessary bits to use these for timing benchmarks.
Fix#23414
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
In the current implementation both SPSR and ELR registers are saved with
the callee-saved registers and restored by the context-switch routine.
To support nested IRQs we have to save those on the stack when entering
and exiting from an ISR.
Since the values are now carried on the stack we can now add those to
the ESF and the initial stack and take care to restore them for new
threads using the new thread wrapper routine.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The current `z_isr_install` implementation asserts that the IRQ to
which the ISR will be installed must be disabled.
This commit disables that assertion for the ARM GIC because the SGI-
type IRQs can never be disabled as per the specifications and this
causes the assertion to fail for them.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Out-of-tree code can still be using the old file locations. Introduce
header shims to include the headers from the new correct location and
print a warning message.
These shims should be removed after two releases.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit renames the `cortex_r` directory under the AArch32 to
`cortex_a_r`, in preparation for the AArch32 Cortex-A support.
The rationale for this renaming is that the Cortex-A and Cortex-R share
the same base design and the difference between them, other than the
MPU vs. MMU, is minimal.
Since most of the architecture port code and configurations will be
shared between the Cortex-A and Cortex-R architectures, it is
advantageous to have them together in the same directory.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit re-organises AArch32 configurations for consistency.
1. Move Cortex-M-specific includes to `cortex_m/Kconfig`.
2. Relocate the "TrustZone" configurations to `cortex_m/tz/Kconfig`
since these are really the TrustZone-M configurations and do not
apply to the TrustZone-A.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Under multi-processing, only the first CPU#0 needs to go through
setting up the kernel structs and clearing out BSS (among others).
There is no need for other CPUs to do those tasks. Since each
Xtensa core starts using the same boot vector, CPUs other than #0
need to skip all the startup tasks by not calling to z_cstart().
So provide another entry point for those CPUs. Note that Xtensa
arch is highly configurable. So the implementation of the entry
point is up to each individual SoC config.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Under SMP, the main BSS section only needs to be zero-ed on CPU #0.
Other CPUs should not zero out BSS, or else it may cause CPU #0 to
crash on invalid data.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Rewrite the comments for the swap routine removing the references to the
old aarch32 code and rename z_arm64_pendsv() ->
z_arm64_context_switch().
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Rework the assembly code for the ISR wrapper and SVC to share the
entry/exit code that is currently scattered amoung several files /
places. No functional changes.
Rename also macro.h -> macro.inc to fool the CI.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
