Instead of including from nrfx_glue.h a specific Zephyr Bluetooth
controller header file that defines PPI and GPIOTE resources to be
reserved for exclusive use by the controller, include a file with
only a fixed name and expect the chosen Bluetooth controller to
provide the location of this file in include paths. This way, when
a different Bluetooth controller implementation is used downstream,
a different file can be easily pointed to.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit fixes invoking of z_log_msg2_runtime_vcreate with wrong
param. This function requires to be called with dynamic or static
source based on CONFIG_LOG_RUNTIME_FILTERING.
Signed-off-by: Przemyslaw Bida <przemyslaw.bida@nordicsemi.no>
Use the devicetree properties to determine if the dedicated temperature or
voltage reference channels should be configured for the ADC.
Fixes#43750.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Introduce ADC properties which indicated if the ADC instances have
dedicated channels for the internal temperature sensor or voltage
reference.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The message type parameter was changed to the more explicit enum.
Existing code with unconfirmed message type has to be updated.
Signed-off-by: Martin Jäger <martin@libre.solar>
The enum did not contain an entry for unconfirmed messages. Instead, it
was only mentioned in the comment that 0 is the default for
unconfirmed messages.
This commit adds LORAWAN_MSG_UNCONFIRMED to the enum and changes the
parameter in the lorawan_send function to enum lorawan_message_type.
Signed-off-by: Martin Jäger <martin@libre.solar>
When queue mode is enabled, state machine will enter state
ENGINE_REGISTRATION_DONE_RX_OFF. This state needs to be
taken into account during registration update to send
correct event.
Signed-off-by: Marin Jurjević <marin.jurjevic@hotmail.com>
Some non-essential peripherals peripherals including various sensors
were enabled by default in the defconfig file when they shouldn't be
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
This reduces power consumption by disabling the internal pull up
resistor on the SAO line of the lis2dh sensor
Signed-off-by: Jamie McCrae <jamie.mccrae@lairdconnect.com>
The stm32's I2C peripheral has a maximum transmission size. Larger trans-
action, that I2C itself allows, can be achieved be using the peripheral's
reload-mode.
In order to do that, st's low-lever drivers need to be informed according-
ly. The previous iteration of the code mishandled the next_msg_flags para-
meter, causing the issue to manifest itself.
This refactors the inner loop of i2c_stm32_transfer() into its own func-
tion. This passes the message parameter by value in order to be able to
mutate its state while keeping the original datum from the user intact
during the entire procedure.
Fixes#43235
Signed-off-by: Frank Terbeck <ft@bewatermyfriend.org>
Claim the net_context mutext associated with a socket before claiming
the socket mutex. The receive callback claims the net_context mutex
internally, which will now always succeed immediately.
The TX path claims the net_context mutex before the socket mutex, and if
we don't use the same order, we can end up in a deadlock.
Fixes#43470.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Following #42026, the body_start pointer now points to the
start of the body fragment in the recv_buffer as long as there
is body in it, either entirely or partially.
Rename the body_start to body_frag_start to better reflect
what it represents.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The littlefs_mount() function sets the mount point for block devices,
so fname[12] shall be generated after calling it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Up till now, the littlefs sample program was only supporting the flash
medium. However, it would be also welcome to be able to test reading and
writing data from littlefs stored on block devices - like SD card.
In this case we do use the block API, to read and write data to it.
To achieve this goal - the CONFIG_APP_LITTLEFS_STORAGE_BLK_SDMMC define
has been introduced.
One can change the disk mount point by defining board specific
CONFIG_SDMMC_VOLUME_NAME.
The test for nucleo board equipped with SD card shall be built with:
west build -p always -b nucleo_h743zi ./zephyr/samples/subsys/fs/littlefs \
-DCONF_FILE=prj_blk.conf
Moreover, the README.rst has been extended to describe running this
test on block devices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The littlefs_flash_erase() function shall be called from flash specific
littlefs_mount function. This allows removal of the stub function
when block device support is added.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This KConfig define (by default defined) is necessary to extend the
littlefs test functionality to support other test scenarios - for
example running it on device with block device (i.e. SD card) backend.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit extends the littlefs test to use binary pattern file.
This file has the 0x55 and 0xAA patterns (to avoid fast wear leveling)
written alternately with special "marks" bytes on each eight position.
Those values are incremented each time the board boots. One can adjust
the size of this file with the TEST_FILE_SIZE define.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The code responsible for incrementing the in-file value has been moved
to the separate function for better readability and reusage.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The code for presenting content of the directory, has been moved to the
separate function to be easily reusable.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Replace calls to printk with LOG_PRINTK to use the logging Zephyr
infrastructure. After this change it would be possible to set the
logging mode (to e.g. reduce the verbosity of output and final size
of the binary).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Definitions of several nRF DK boards are missing flash and ram sizes.
This commit adds those missing entries.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
It may happen that after the flash chip was previously put into
the Deep Power Down mode, the system was reset but the flash chip
was not. Consequently, the flash chip can be in the DPD mode when
the QSPI driver is initialized. Some flash chips will just exit
the DPD mode on the first CS pulse, but some need to receive the
dedicated command to do it and they will not respond to any other
commands including those that the driver need to perform to complete
its initialization ("Read status register" and "Read JEDEC ID").
This commit adds sending of the "Release from Deep Power Down"
command right after initialization of the QSPI interface to avoid
the problem described above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Previous commit 579ca90e25 to
build wifi drivers as a library changed the include path for
the WINC1500 driver, which results in the include path being
local to the library. However, the Atmel HAL requires
wifi_winc1500_nm_bsp_internal.h to in the search path. So
change the include path to be global.
Fixes#43456
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The gsm modem should be able to be started or stopped freely,
independent from the networking state.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The `starting` flag causes the sample to work only if
GSM_PPP_AUTOSTART is enabled, its initial value should be
dependent on GSM_PPP_AUTOSTART.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
This fixes data path configuration that was done for both directions
even if CIS was unidirectional. To ensure the data path shall be
configured, the QoS SDU is checked.
Fixes: #43190
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Get rid of all those global variables and scheduler locking.
Use the reguler IRQ exit path to let tests properly validate preemption.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
This test was working by accident onarm64 and riscv64. Those
architectures have large register files, even more so considering
their 64-bit nature.
This test works by calling k_object_alloc(K_OBJ_THREAD) until thread
index exhaustion. However here it exhausted heap memory before running
out of thread indexes. There was a test to make sure that wasn't the
case by attempting a k_malloc(256). But here that succeeded just
because 256 is far smaller than a struct k_thread on the above
architectures.
Fix this by:
- attempting an additional allocation with the actual object size
instead of an arbitrary 256 bites
- increasing the heap size as 8192 was clearly insufficient for the
above platforms.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Git describe should work in eg. shallow clones when there are no tags.
Has been fixed in cmake previously, but not in twister.
Signed-off-by: Andreas Pettersson <andreaspettersson95@gmail.com>
When running twister with --only-failed option, based on last xml
result, the new skipped count should be the last skipped count
plus current skipped count.
Signed-off-by: Chen Peng1 <peng1.chen@intel.com>
Execute log_setup even when test is skipped. This is especially
vital when test infrastructure is using logging (e.g. LOG_PRINT
is enabled).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
