Add binding fro stm32wl-rcc.yaml that derivates from stm32wb-rcc.
Additionally update stm32wb-pll-clock.yaml to be used as well
for stm32wl series and add missing div-m property.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add clocks node and clocks to stm32l5 series.
PLL binding is reused from stm32l4 series.
Matching binding is updated to document that.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add clocks nodes for F0/F3/G0/G4 series.
For F0 and G0 series, update compatible for rcc node
to specify use of dedicated "st,stm32f0-rcc" compatible.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add bindings for F0/F3/G0/G4 clocks.
Introduce new rcc binding "st,stm32f0-rcc" binding
that describes RCC hardware blocks that don't have
"apb2-prescaler".
This binding also applies to G0.
Binding "st,stm32f0-pll-clock" is used for both F0
and F3 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add PLL bindings for STM32F1 devices.
- Main PLL binding for STM32F1 non connectivity lines
- Main and PLL2 binding for Connectivity lines (F105/F107)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove default pll settings to ensure pll users are correctly
configuring all prescalers on purpose and avoid surprises.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds flash clock settings in device tree for stm32h7
series such that the stm32h7 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The current serial driver uses hard code configuration. Rework driver
to use pinctrl and enable full configuration from device tree.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add a function that uses the JESD216 SFDP BFP DW16 Enter 4-Byte
Addressing parameter to put the device into 4-byte addressing mode if
one of the entry modes that's supported by the driver is available on
the device.
Perform the transition if SFDP data is provided (either by devicetree
or at runtime), or if a special devicetree property provides the entry
mode descriptor.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Provided nodes reflect the clock tree of each series.
Clock nodes are disabled by default but populated with default
start up configuration. Main reason is the we don't want to
impact boards using Kconfig based clock configuration for now.
Exception to these rules:
- syslck: Default enabled, clock frequency and clock source not
provided
- pll: clock source not provided
This is made on purpose so that errors are triggered if parameters
essential to the board configuration are not provided.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This CL adds a override mechanism for pwm module's input clock source
assignment. If the 'clock-bus' property exists, the NPCX_DT_PROP_ENUM_OR
macro function will return an enum upper token value. Otherwise, it
expands to default value in 'clocks' property.
For example, if the users want to select LFCLK as pwm0's input clock,
ths node can be overridden by adding 'clock-bus' property with an enum
string, "NPCX_CLOCK_BUS_LFCLK".
&pwm0 {
status = "okay";
clock-bus = "NPCX_CLOCK_BUS_LFCLK";
};
Signed-off-by: Keith Short <keithshort@google.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
i2s1 is not present in all stm32f4 series. So moving the i2s1 node
from the top level stm32f4 dtsi file to the stm32fxx specific dtsi
files. Also in stm32f429zi, the sequence starts from i2s2, this commit
helps in having the right channel number.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
STM32G0 is supported by the st,stm32-dma-v2 driver.
This commit adds dma1 and dmamux dts bindings
for stm32g03x, stm32g05x and stm32g07x.
For stm32g0bx additionally dma2 is added.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Exit latency is the maximum time required by a CPU to transition from
a specific idle state to active state. This information is going to be
used to properly configure the wake up event in order to the system be
able to execute the next scheduled task.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This patch adds flash clock settings in device tree for stm32wb
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32l4
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32l1
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32g4
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32g0
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This change enables A, C, D, E, G, H, I, J, K, and L groups,
and fix gpio interrupt function.
This change also pull (and rename) dt-bindings/irq.h to
dt-bindings/interrupt-controller/ite-intc.h, because it is
chip-specific.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Change-Id: Ifee039981c2cc4cf5980e663702a9921e629fc1e
NPCX PWM supports output buffet select to push-pull or open-drain. Add
output buffer select option 'drive-open-drain' in devicetree for NPCX
PWM. If set, the PWM output will be configured as open-drain. If not
set, defaults to push-pull.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
The binding-template.yaml file has grown organically into something
that's out of control.
It makes too many 'see above' and 'see below' references to be read
comfortably, and we can't cross reference from YAML.
There are also many example DTS and YAML fragments scattered about in
comments, which cannot be syntax highlighted properly.
Fix that by overhauling the documentation into bindings.rst in the DT
guide. This will let us link to individual sections when answering
questions, allows us to cross-reference and use '.. code-block::',
etc.
A couple of things need to go to other pages.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
1. add a seperate 2 cores SMP board configuration to run in Jailhouse
inmate Cell, root Cell Linux will use Core0 and Core1, Zephyr will
run on Core2 and Core3.
2. Refine the code of dts, move SoC common dts nodes into dtsi fiel in
dts/arm64/nxp/ directory.
3. Add myself to be code owner of directory dts/arm64/nxp/.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
