There is possibility that endrx interrupt will be triggered in the
middle of timer interrupt responsible for UARTE timeout, this
patch handles this case.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Update calls to nrfx HAL functions to reflect API changes introduced in
nrfx 2.0.0. All these functions are now called with the first parameter
pointing to the structure of registers of the relevant peripheral.
Also a few functions got renamed:
- nrf_gpiote_int_is_enabled to nrf_gpiote_int_enable_check
- nrf_gpiote_event_is_set to nrf_gpiote_event_check
- nrf_rng_event_get to nrf_rng_event_check
- nrf_rng_int_get to nrf_rng_int_enable_check
- nrf_rtc_event_pending to nrf_rtc_event_check
- nrf_rtc_int_is_enabled to nrf_rtc_int_enable_check
- nrf_timer_cc_read to nrf_timer_cc_get
- nrf_timer_cc_write to nrf_timer_cc_set
Default configuration values were removed from nrfx_config files,
so the drivers pwm_nrfx and spi_nrfx_spis no longer can use those.
Function nrfx_pwm_init() now takes one more parameter - context pointer
that is passed to the event handler, not used in the pwm_nrfx driver.
HALs for UART and UARTE now allow configuration of the parity type
and the number of stop bits, for SoCs that provide the corresponding
registers.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In some applications where power management is used, it is not expected
that the GPIO pins of the UARTE is reconfigured upon power state change.
Added a Kconfig option to disable the UARTE driver management of GPIOs.
It defaults to y in order to not affect current behavior unless the user
configures it specifically.
Signed-off-by: Dennis Wildmark <dennis.wildmark@assaabloy.com>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
nrf52840 and nrf9160 have possible configuration of two stop bits
for UART and UARTE, this commit adds handling of it to driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Configure pins before enabling and after disabling UARTE through
power management functions.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Ensure that two routines won't interfere with eachother.
In current situation there is possibility that ENDRX will be called
during rx_timeout routine or vice-versa which will result in wrong
offset and length passed to user.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Due to longer than expected user callback handling, rx byte counting
got out of sync with real values. It leads to incorrect values
reported to user. This fix adds sync point at the end of buffer.
When using hardware rx counting this issue should not occur.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If reception was longer than rx timeout, UART_RX_RDY event
would provide data with delay, and synchronise at buffer end.
This change makes sure that all data is given to user when timeout
occurs.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Without first triggering TASKS_STOP{RX,TX}, I observed that the UARTE
was never disabled when using device_set_power_state which resulted in
the HFCLK never being shut down and several hundred microamps in
unnecessary current consumption when idle. This seems to fix the issue.
Also added special treatment of uarte if CONFIG_UART_ASYNC_API is
selected. Note that the #ifdef isn't enough, since it's possible that
the option is set, but only one of the UARTs uses it.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
Bad order of interrupt calls made it unable to transmitt data
using interrupt driven API.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Calling fifo_fill function from uart_nrfx_uarte in the same
interrupt more than once, would break previous transmission.
Following fix adds checking if previous data was sent, and
if not, returns 0.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
Zephyr UART drivers offer very low-level functionality. Oftentimes,
it would be useful to provide higher-level wrappers around UART
device which would offer additional functionality. However, UART
driver irq callback routine receives just a pointer to (low-level)
UART device, and it's not possible to get to a wrapper structure
(without introducing expensive external mapping structures). This
is an indirect reason why the current UARt wrappers - uart_pipe,
console - are instantiated statically just for one underlying UART
device and cannot be reused for multiple devices.
Solve this by allowing to pass an arbitrary user data to irq
callback, set by new uart_irq_callback_user_data_set() function.
Existing uart_irq_callback_set() keeps setting a callback which
will receive pointer to the device.
While public API maintains compatibility, drivers themselves need
to be updated to support arbitrary user data storage/passing (as
legacy uart_irq_callback_set() functionality is now implemented in
terms of it).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
1. dts.fixup files updated with peripheral address and IRQ NUMBER.
2. Peripheral address is taken from DT.
3. IRQ number is taken from DT.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
1. Added support for two instances of UARTE.
2. Kconfig.nrfx is capable to configure UART and UARTE driver.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
